Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AddEnergie CoRe+V2
Summary of Contents for AddEnergie CoRe+V2
- Page 1 CoRe+ Installation Guide...
- Page 2 IMPORTANT Split Phase 120/240 VAC Supply or 3 phase 120/208 VAC (must be protected by a 40 A fuse or circuit breaker) Both lines must have 120V between ground. Voltage supply must be grounded. Require 2 lines and 1 ground connection. Neutral is not used. (Refer to Figure 1 and Figure 2) Maximum output power: 7.2 kW @ 240 VAC or 6.3 KW @ 208 VAC Built-in protection against overvoltage conditions and leakage current to ground Connect the power supply of the EVSE with caliber 6 to 8 copper conductors...
-
Page 3: Table Of Contents
Table of contents Introduction ........4 Statement . -
Page 4: Introduction
Introduction IC Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-3 (A) / NMB-3 (A) FCC Notice (for USA only) This equipment has been tested and found to comply with the limits for a Class A digital device,... -
Page 5: Statement
Split Phase 120/240 VAC Supply or 3 phase 120/208 VAC (must be protected by a 40A breaker or fuse) Maximum output current( power): • CoRe+V2 and CoRe+VBV2: 30A (7.2 kW @ 240V or 6.3 kW @ 208V) • CoRe+PSV2: Dynamically controlled by a site controller between 8A and 30A (between 1.7 kW et 7.2 kW) Built-in protection against overvoltage conditions and leakage current to ground Operating Temperature Range: -40°C to +50°C... -
Page 6: Installation And Safety
Installation and Safety INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR ELECTRIC SHOCK IMPORTANT SAFETY INSTRUCTIONS - PLEASE DO NOT DISCARD THESE INSTRUCTIONS WARNING – When using electric products, basic precautions should always be followed, including the following. This manual contains important instructions for Model CoRe+ that shall be followed during installation, operation and maintenance of the unit. -
Page 7: Dimensions
Dimensions 19 cm 14 cm 9.5 cm (7.5’’) (5.5’’) (3.75’’) Patron de perçage: 33 cm 47 cm (13’’) Drilling pattern: (18.5’’) 154 cm (60.5’’) 130 cm (51.125’’) GROUND 2016 ADDÉNERGIE TECHNOLOGIES INC. ALL RIGHTS RESERVED. Information and Specifications Contained in this Document are Subject to Change, Amendments, and Additions at any Time, Without Notice... -
Page 8: Wall Or Post Mounting
Wall or Post Mounting Power cable entry under the station • Avoid installing the EVSE in bad weather • IMPORTANT, never conditions. remove the protection plate of the keyhole. L1 L2 • Connect two power conductors (L1 and L2) and the ground •... - Page 9 Wall or Post Mounting Power cable entry from the back • Remove the plate to avoid the splatter of particles in the equipment. • IMPORTANT, never • Punch a hole of the appropriate diameter to remove the protection install the cable connector. plate of the keyhole.
- Page 10 Wall or Post Mounting With electrical box • IMPORTANT, never remove the protection plate of the keyhole. • Remove the backplate. • Install the head base in order to align the rectangular opening with the box opening in the wall or the post. •...
-
Page 11: Closing The Housing Of The Station
Closing the Housing of the Station Output • Data cable • Connect the cables to their connectors. • Ground • O-ring • Install the head to the base, making sure that the seals stay in place, then install the four mounting screws. •... -
Page 12: Preliminary Tests And Commissioning
Preliminary Tests and Commissioning Instructions: • Apply power to the charging station, the following should be observed immediately after power is turned on: 1: The status light is on continuously, its color will be green 2: The display shows the greeting message •... -
Page 13: Power Sharing
Power Sharing With the embedded « PowerSharing » capability of the CoRe+PS, up to four charging stations can be connected in parallel to the same branch circuit 1. The charging stations connected in parallel to a same branch circuit must be the CoRe+PS model (the specific model identification can be found on the unit label). - Page 14 (877) 505-2674 ext. 203 AddÉnergie Technologies Inc. Eastern office: 2327, Versant Nord Boulevard, office 120, Québec (QC) G1N 4C2 CANADA Central office: 7420 Airport Road, Mississauga (ON) L4T 4E5 CANADA Contact Us T. 1 877 505-2674 F. 855 505-2674 info@addenergie.ca addenergie.ca...
Need help?
Do you have a question about the CoRe+V2 and is the answer not in the manual?
Questions and answers