Download Print this page

Advertisement

Quick Links

02DORM0707-V1
WARNING: Only for domestic use
Not suitable for children under 36 month
To be used under direct supervision of an adult
Overall Dimensions:
Length = 2103mm
Width = 2091mm
Height = 2382mm
Base Dimensions:
Length = 2076mm
Width = 2060mm
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be a ected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are delivered pre-treated with a water based timber treatment
however this only helps to protect during transit of your garden item. To
validate your guarantee and for better protection against weathering it is
ESSENTIAL that you treat the garden building with a wood preserver within 3
months of assembly. This will need to be re-applied annually to ensure longevity
of your building. Care must be taken when constructing the garden building
that it is not touching the ground and is on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed: Ensure that there will be access to all sides for maintenance
work and annual treatment.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be
slightly smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also
recommended that the oor be at least 25mm above the surrounding ground level to avoid ooding.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products independently tested to EN71 level part
1,2,3&8. We cannot accept responsibility for your safety whilst erecting or using this product. Children of any age should not be left to play unsupervised.
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every e ort has been made during the
manufacturing process to eliminate any prospect
of splinters or rough surfaces to the wood
occurring. You are strongly advised to lightly sand
o any splinters or rough surfaces you may nd
before allowing children to use the building.
x2
This building should be erected by
two adult people.
For ease of assembly, it is advisable to
pilot drill all screw holes and ensure
all screw heads are countersunk.
2mm Drill bit
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
For Assistance Please
Contact Customer Care on
01636 880514
Please retain product label and instructions for future reference
1
Floor Qty 1
4
Plain Panel Qty 1
Window Panel
9
10
Veranda Front
Veranda Side
Qty 2
Qty 2
13
14
Large Bunk Floor
Small Bunk Floor
Qty 1
Qty 1
21
20
19
Door
Qty 1
Window Cross
Rail End
Rail
Qty 1
Qty 1
2
Veranda Floor Qty 1
Door Panel Qty 1
5
6
Window Gable Qty 1
7
Plain Gable Qty 1
Qty 2
11
Window Roof Qty 1
Plain Roof Qty 1
15
16
Left Side
Dormer Window
Right Side
Panel Qty 1
Panel Qty 1
Panel Qty 1
24
25
23
22
Ply
Wooden
Corner
Triangle
Bracing
door handle
Qty 6
Qty 1
Qty 1
Qty 1
3
8
Front Panel
Qty 1
12
18
17
Dormer Roof
Sheet Qty 2
26
Hinge
Qty 2

Advertisement

loading
Need help?

Need help?

Do you have a question about the 02DORM0707-V1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Mercia Garden Products 02DORM0707-V1

  • Page 1 1,2,3&8. We cannot accept responsibility for your safety whilst erecting or using this product. Children of any age should not be left to play unsupervised. Wooden Corner Window Cross Rail End Triangle Qty 2 Bracing door handle Rail Qty 6 Qty 1 Qty 1 Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN Qty 1 Qty 1 Qty 1 www.merciagardenproducts.co.uk...
  • Page 2 Fixing Kit Right Hand Rail - 27x44x1704mm Qty 1 Left Hand Rail - 27x44x1890mm Qty 1 Ladder Side Left - 27x95x1418mm Qty 1 Hand Rail support - 27x44x254mm Qty 2 Ladder Side Right - 27x95x1418mm Qty 1 Window Bar - 505 Nail Bag Window Bar - 473 70mm Screw x 33...
  • Page 3 Step 4 Step 2 Fix the Veranda oor to the Fix the remianing window oor using oor joining blocks. panel and the door panel using Fix them together using the same method described in 2x30mm screws per block step 3. screwing through the oor into the blocks.
  • Page 4 Step 6 Step 8 Fix the remaining veranda front, Place the plain gable onto the side and panel joining frame plain panel, ensuring the using the same methods shown cladding and framing on either in step 5. side is flush (see diagram). Fix with 4x50mm screws as shown in diagram.
  • Page 5 Step 10 Step 12 Fix both the window roof and Fix the bunk support ensuring plain roof as illustrated, making Ensure horizontal the top is in line with the sure both roofs fit evenly frame is flush with horizontal frame on the plain back frame.
  • Page 6 Step 14 Step 16 Sit the Large bunk floor ontop of Place rail end into position, the door panel framing and fix ensure overhang is butt against using 5x70mm screws. the bunk floor side. Also fix the bunk to the Fix to the floor and side panel surrounding panels using using 6x50mm screws.
  • Page 7 Step 18 Step 20 To assemble the ladder, slot each The next step is to fit the ladder hand rails. First attach the right hand ladder step into the grooves of 50mm rail to the rear panel using 4 x 50mm screws, pre drill holes first and screw the ladder sides and fix using make sure the screws are fixed into the rear panel framing .
  • Page 8 Step 23 Step 21 Place the ridge bar in between the Fix the framing together with 3x dormer window and window roof 50mm screw as shown in panels. Ensure the at edge is diagram. against the dormer window panel and the angled edge is resting on the window roof.
  • Page 9 Step 27 Step 25 Fix the eaves frames to the side Cut the felt into 6 sheets as shown in the panels ensuring they are butt illustration and lay onto the roof as up to the roof sheets using shown in the diagram ensuring there is a 3x50mm screws each.
  • Page 10 Step 29 Secure the long and short fascias as shown in the illustration using 3x40mm screws for the long fascias and 2x40mm screws for the short fascias. Pre-drill holes to avoid the wood spliting. 140x felt tacks 16x 40mm screws Step 28 Step 30 Secure the long and short...
  • Page 11 Step 31 Place a window cross against the inside of each window. Position the frame centrally to the window and x using 4x20mm screws per frame. Place the wooden door handle on the outside of door and use Remove film from both sides of styrene before fitting a 60mm screw from the inside to secure.