Z-Wave Panic Button User Manual

Z-Wave Panic Button
®
User's Manual
Introduction
The Panic Button is a wireless switch designed to control the Panic or
Scene status of other associated devices through the Z-Wave controller.
After receiving the signals emitted by the Panic Button, the Z-Wave
controller can then give commands or operate according to its own
settings. Its great compatibility with Z-Wave products makes it suitable
for smart home cloud based gateway.
The Panic Button is also a security Z-Wave device and supports the Over
The Air (OTA) feature for the product's firmware upgrade. If you want it
to be a security device that use secure/encrypted message to
communicate in a Z-Wave network, then a security enabled Z-Wave
controller is needed.
Package Contents
Panic Button x 1
User Manual x 1
Command Class
Z-Wave® Panic Button Command Class Supported
COMMAND_CLASS_ZWAVEPLUS_INFO_V2,
COMMAND_CLASS_SUPERVISION_V1,
COMMAND_CLASS_BATTERY_V1,
COMMAND_CLASS_WAKE_UP_V2,
COMMAND_CLASS_TRANSPORT_SERVICE_V2,
COMMAND_CLASS_SECURITY_V1,
COMMAND_CLASS_SECURITY_2_V1,
COMMAND_CLASS_VERSION_V3,
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
COMMAND_CLASS_ASSOCIATION_V2,
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1,
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3,
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2,
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1,
COMMAND_CLASS_POWERLEVEL_V1,
COMMAND_CLASS_NOTIFICATION_V8,
COMMAND_CLASS_CONFIGURATION_V1,
Security
COMMAND_CLASS_ASSOCIATION_V2,
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3,
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1,
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2,
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1,
COMMAND_CLASS_POWERLEVEL_V1,
COMMAND_CLASS_NOTIFICATION_V8,
COMMAND_CLASS_CONFIGURATION_V1,
COMMAND_CLASS_BATTERY_V1,
COMMAND_CLASS_WAKE_UP_V2,
COMMAND_CLASS_VERSION_V3,
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Panic Button Device Information
Basic Device Class: ROUTING_SLAVE
Generic Device Class: SENSOR_NOTIFICATION
Specific Device Class: NOTIFICATION_SENSOR
Detailed description of each command class
【COMMAND_CLASS_ZWAVEPLUS_INFO】
The Z-Wave Plus Info Get Command is used to get additional information of
the Z-Wave Plus device in question.
【COMMAND_CLASS_SUPERVISION】
The Supervision Command Class allows a sending node to request
application-level delivery confirmation from a receiving node. The delivery
confirmation includes relevant application-level status information in the
confirmation message. The Supervision Command Class MAY be used for
solitary commands such as Set and unsolicited Report commands.
The Supervision Command Class MUST NOT be used for session-like
command flows such as Get←→Report command exchanges or firmware
update.
【COMMAND_CLASS_BATTERY_V1】
The Battery Command Class is used to request and report battery levels for
a given device.
【COMMAND_CLASS_WAKE_UP_V2】
The Wake Up Command Class version 2 enables read back of the Wake Up
Interval capabilities in a node.
The Z-Wave Panic Button wakes up by wake up timer or presses the physical
button once, it will send Wakeup Notification Command to the node ID that
requires to be reported and stay awake for 10 seconds, if no
WAKE_UP_NO_MORE_INFORMATION command is received.
【COMMAND_CLASS_TRANSPORT_SERVICE_V2】
The Transport Service Command Class supports the transfer of datagrams
larger than the Z-Wave frame.
【COMMAND_CLASS_SECURITY_V1】
The Security Command Class create the foundation for secure application
communication between nodes in a Z-Wave network. The security layer
provides confidentiality, authentication and replay attack robustness
through AES-128.
【COMMAND_CLASS_SECURITY_2_V1】
The Security 2 Command Class is a framework for allowing nodes to
communicate securely in a Z-Wave network. The Security 2 Command Class
provides backwards compatibility to nodes implementing the Security 0
Command Class. Security 2 Command Class also defines a new
encapsulation format, new Security Classes and a new KEX Scheme 1, which
together offers a number of advantages over the Security 0 Command Class.
Security 2 Command Class is scalable and allows more KEX Schemes,
Security Classes and encapsulation formats to be introduced in the future if
necessary.
【COMMAND_CLASS_VERSION_V3】
The Version Command Class, version 3 allows supporting nodes to advertise
capabilities related to the Version Command Class and optionally provide a
detailed list of information regarding implementation on the Z-Wave chip.
【COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4】
【COMMAND_CLASS_ASSOCIATION_V2】
The Association Command Class is used to manage associations to NodeID
destinations. A NodeID destination may be a simple device or the Root
Device of a Multi Channel device.
【COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3】
The Multi Channel Association Command Class is used to manage
associations to Multi Channel End Point destinations as well as to NodeID
destinations.
【COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1】
The Association Group Information (AGI) Command Class allows a node to
advertise the capabilities of each association group supported by a given
application resource. Controllers and installer tools SHOULD use AGI
information to support controller-assisted button-to-button association and
GUI-based drag-and-drop association in a plug-and-play fashion.
Centralized gateway-based deployments may create a single association
from the lifeline association group to a central management application.
Group Name Description
Lifeline group, association with 5
1 "Lifeline"
nodes.
ON/OFF group, association with 5
2 "Basic set"
nodes.
When the key is press and hold the button more than 1.5 seconds, a
BASIC_SET command will sent On(0xFF) or Off(0x00) to the nodes of
Grouping 2.The Basic Command Class support Version 2.
【COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2】
Manufacturer Specific Command Class, version 2 adds a set of commands to
communicate unique identification, e.g. the serial number, of the product.
Commands not mentioned here remains unchanged as specified for
Manufacturer Specific Command Class, Version 2.
【COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1】
The Device Reset Locally Command Class is used to notify central controllers
that a Z-Wave device is resetting its network specific parameters.
【COMMAND_CLASS_POWERLEVEL_V1】
The Powerlevel Command Class defines RF transmit power controlling
Commands useful when installing or testing a network. The Commands
makes it possible for supporting controllers to set/get the RF transmit power
level of a node and test specific links between nodes with a specific RF
transmit power level.
【COMMAND_CLASS_NOTIFICATION_V8】
The Notification Command Class is used to advertise events or states, such
as movement detection, door open/close or system failure. The Notification
Command Class supersedes the Alarm Command Class.
Notification Type Notification events
0x07 0x00
(Home Security) (Previous event clear)
0x08
(Button detected)
【COMMAND_CLASS_CONFIGURATION_V1】
The Configuration Command Class allows product specific configuration
parameters to be changed. One example could be the default dimming rate
of a light dimmer.
This class is used for setting certain vendor specific configuration variables.
Default
ID Name Size Range Description
value
1~100, 1~100:LED light up 1 ~ 100
LED Light up
Seconds.
1 1 127 127
Time
127:always on
0 : Disable
0,
1~100: Sound 1~100 beeps
Buzzer beep
2 1 1~100, 127 (0.5s on, 0.5s off)
times
127 127: Continue beep till cancel
trigger
Product Overview
LED Indicator
LED Signal
OFF No Power/paired and ready to be
triggered (with battery)
Solid Red Device had been triggered
Red blink three times at Inclusion successful/Exclusion
one blink per second successful/Parameter successfully
set
Red blink two times at Device had been deactivated and
one blink per second back to standby mode
Red blinks at one blink Low battery
per three seconds
Red blinks for 30
seconds at one blink per
two seconds
Solid Red for 5 seconds
Button Function
Function
Inclusion
Exclusion
Reset
Trigger
Deactivate
Specification
Z-Wave
Panic Button
RF Protocol
Power Source
Z-Wave Frequency
Data Rate
Operation Range
LED Indicator
Button
Waterproof Level
Operation
Temperature
Regulatory
Approvals
Dimensions
(L*W*H)
Regulatory Compliance
CE Caution
Electromagnetic compatibility and Radio spectrum Matters (ERM); Short
Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1,000
MHz frequency range with power levels ranging up to 500 mW; Part 2:
Harmonized EN covering essential requirements under article 3.2 of the
R&TTE Directive.
FCC Caution
This device complies with Part 15 of the FCC rules standard. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the authority to operate equipment.
This device and its antenna must not be co-located or operating in
conjunction with any other antenna or transmitter. This equipment complies
with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance
Button 20cm between the radiator & your body. This equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
LED Indicator equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
Status
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
-
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device is in unpaired mode
and waiting to be inclusion
The device is in paired mode when
insert batteries
Operation
Push the button three times in 1.5 seconds.
When inclusion successful, the LED will be
RED blink three times.
Push the button three times in 1.5 seconds.
When exclusion successful, the LED will be
RED blink three times. And the LED will be
red blinking for 30 seconds at one blink per
two seconds. The device is now waiting to
inclusion.
Push the button three times in 1.5 seconds and
hold the third push for 10 seconds till the LED
is red blinking. When reset is successful, the
device is set to factory default and now waiting
to inclusion
Please use this procedure only when the
network primary controller is missing or
otherwise inoperable.
Push and hold the button more than 1.5
seconds.
When the device is triggered, push and hold the
button more than 6 seconds. The buzzer will
mute and the LED will be red blinking two
times.
®
Specification
Z-Wave Plus (S2)
DC 3V, AAA batteries x 2
EU:868.42 MHz
US:916.00 MHz
JP: 922.5 MHz
9.6kbps/40kbps/100kbps
100 feet (About 30M)
RED
X 1
(Inclusion/Exclusion/Trigger/Reset)
IPX4
-10~40℃
CE / FCC/TELEC / Z-Wave® Plus
80 x 80 x 40.5 mm