Download
Share
Print this page
Z-Wave PSR04 Manual
  1. Manuals
  2. Brands
  3. Z-Wave Manuals
  4. Switch
  5. PSR04
  6. Manual

Z-Wave PSR04 Manual

Hide thumbs
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
PSR04 Programmable button Switch
Full Color LED 1
Touch Button
Fig. 1 Assembling
This round device is a flexible and multi functions button switch. It is able to
switch the appliances on/off or activate the scenes and macros which are preset
already. The rotation sensor make it possible to adjust the percentage of
dimmer or thermostat. It can also work as a timer. The well designed wall
bracket and magnetic back let the switch can be fixed on the wall, Plus
enabled device and is fully compatible with any Z-Wave
Note:
Please provide a 5 DVC voltage through Micro USB Port
to wake the device up before the first using.
The rotation function and tim er functions w ork only
when the device is fitted upright or stick on the w all or
Red LED
the device will only w ork as an on/off sw itch w hen fitted
horizontal.
LED indicators
1. LED type and locations
There are two sets of LED embedded in the device.
A.
B.
2. Low battery
The device will enter low battery mode when the battery power is under
20%. The red LED flashes three times every one minute.
Full Color LED 2
3. NWI Auto Inclusion
The red LED will flash quickly for 30 seconds when device entering in NWI
mode.
4. Percentage adjustment mode
The full color LED will turn from blue to yellow then from yellow to red
gradully according to the percentage from 0% to 100%.
5. Timer mode
A.
B.
1
Set 1: Two full color LED lights round the device.
Set 2: One red LED under the arrowhead on at the front side.
The red LED will flash once when device entering/exiting the timer
mode..
The full color LED will flash once every 10 seconds and the color will
TM
TM
enabled network.

Advertisement

loading

Related Manuals for Z-Wave PSR04

Summary of Contents for Z-Wave PSR04

  • Page 1 It can also work as a timer. The well designed wall bracket and magnetic back let the switch can be fixed on the wall, Plus enabled device and is fully compatible with any Z-Wave enabled network. Note:...
  • Page 2 The full color LED will flash with pink light every 1 second when countdown from 5. The red LED will flash 6 times with white when time’s up. Z-Wave Network Setting Up There is a touch button on the front side. The button carry out inclusion, exclusion and reset to default.

  • Page 3: Switch On/Off

    B and turn on the lamp by touching the touch button then adjust the percentage you want. Switch On/Off PSR04 is able to work as an On/Off state switch by pressing the touch Fig. 3 Timer Table button when pointing the arrowhead to area B or fitting horizontal.

  • Page 4: Z-Wavetm Notification

    Class, it can receives the updated firmware image sent by controller via the default. When it wake-up it will broadcast the “Wake Up Notification” Z-wave RF media. It is a helpful and convenient way to improve some function if message to the network, and wake-up 10 seconds for receive the setting commands.

  • Page 5: Security Network

    PSR04-2: 908.40MHz; 916.00MHz(USA/Canada) / The device support the security function. When the device included PSR04-3: 922.5MHz/ 923.9MHz/ 926.3MHz (Taiwan/JP) with a security controller, the device will auto switch to the security mode. In the security mode, the follow commands need using Security ** Specifications are subject to change and improvement without notice.

  • Page 6: Fcc Interference Statement

    This marking indicates that this product should not be disposed with This device complies with Part 15 of the FCC Rules. Operation is subject other household wastes throughout the EU. To prevent possible harm to the following two conditions: to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material (1) This device may not cause harmful interference, and resources.