Advertisement
Quick Links
Thank You for your purchase of a Sanus Systems Vision Mount! The VMPO is designed to securely attach a Flat Panel LCD to a cabinet
or an armoire. It will allow the ability to pull the TV out and swivel. It can also be used with a VM200 for tilting LCDs or a VMPL50
for Plasmas.
Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified
contractor or contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective
parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replace-
ment parts for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Improper instal-
lation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified by Sanus Systems.
Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call
Sanus Systems before returning products to the point of purchase.
Required Tools: Drill, 1/4" Drill Bit, wrench or socket set, phillips screw driver
Check carefully to ensure that no hardware or parts are missing
Note: Hardware shown at actual size *Some items not shown at same scale
(6) Button Head Bolt - a
(4) M8 Nut - d
(4) Furniture Bolt - g
(1) Base - j
(1) Top Assembly - m *
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Assembly Instructions for Model: VMPO
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 4.05.05
(6) 1/4 20 Nut - b
(4) M8 x 16 Bolt - e
(4) Wood Screw - h
(1) Left Glide - k
(1) Handle - n
(6) Washer - c
(4) M8 Lock Washer - f
(1) Allen Key - i
(1) Right Glide - l
(1) Front Cover - o
Advertisement
Related Manuals for Sanus Systems VISION MOUNT VMPO
Summary of Contents for Sanus Systems VISION MOUNT VMPO
- Page 1 Assembly Instructions for Model: VMPO Thank You for your purchase of a Sanus Systems Vision Mount! The VMPO is designed to securely attach a Flat Panel LCD to a cabinet or an armoire. It will allow the ability to pull the TV out and swivel. It can also be used with a VM200 for tilting LCDs or a VMPL50 for Plasmas.
- Page 2 TV Attachment Hardware: (4) M4 x 10 Bolt - p (4) M4 x 30 Bolt - q (4) M6 x 12 Bolt - r (4) M6 x 35 Bolt - s (4) M4 Lock Washer - t (4) M6 Lock Washer - u (4) M4 Spacer - v (4) M6 Spacer - w Step 1: Prepare Holes in Mounting Surface...
- Page 3 Step 2: Attach Glides to Mounting Surface To mount the Glides (k,l), insert a Button Head Bolt (a) through each indicated hole in the wood portion of the Glide, the Shelf you are mounting the VMPO to, a Washer (c), and finally thread a 1/4 20 Nut (b) onto the end. See the Detailed View of Diagram 2 for assistance. Tighten the Nut with a wrench until tight.
- Page 4 Step 4: Attach Top Assembly to Glides Orient the Base (j) so that the 4 small holes face the front and the side with the long grooves faces down. Then orient the Top Assembly (m) so that the vertical tube is closer to the back. Insert a Furniture Bolt (g) through the Top Assembly, the Base, and finally thread it into the Glide (k,l).
- Page 5 Step 6: Adjust the height of the Top Assembly Using the Allen Key (i), loosen the pin that is shown in the Detailed View of Diagram 6. Once the Pin and the Nut are removed, raise or lower the free moving part of the Top Assembly (m) to the desired height and reinsert the Pin and the Nut into the appropriate hole. Tighten with the Allen Key.
- Page 6 Step 7: Attach Flat Panel LCD directly to VMPO To figure out the hardware needed to attach the VMPO directly to the TV, start by determining the diameter of the Bolt (M4 or M6) your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately! Once you have determined the correct diameter, see the appropriate Diagram below.
- Page 7 If using a VM200 for tilt compatibility with flat panel LCD sets follow Step 8. Step 8: Attach the VM200 Wall Plate to Top Assembly Insert a M8 Bolt (e) through the appropriate hole in the VM200 Wall Plate, the Top Assembly (m), the M8 Lock Washer (f), and thread into a M8 Nut (d).
- Page 8 Note: Proceed to follow the instruction manual that came with the VMPL50 Wall Mount to attach the Television to the wall plate. Diagram 9 VMPL50 Wall Plate Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 4.05.05 Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com...