Download
Share
Print this page
Diamondback 1260Sc Owner's Operating Manual
  1. Manuals
  2. Brands
  3. Diamondback Manuals
  4. Fitness Equipment
  5. 1260Sc
  6. Owner's operating manual

Diamondback 1260Sc Owner's Operating Manual

Hide thumbs Also See for 1260Sc:

Advertisement

Quick Links

Download this manual
1260Sc OWNER'S OPERATING MANUAL

Advertisement

loading
Need help?

Need help?

Do you have a question about the 1260Sc and is the answer not in the manual?

Questions and answers

Related Manuals for Diamondback 1260Sc

Summary of Contents for Diamondback 1260Sc

  • Page 1 1260Sc OWNER’S OPERATING MANUAL...
  • Page 2 Main Frame Handle Bar Seat Front stabilizer Rear stabilizer Console tube Console END CAP (A45) (E4 / E5) (K1)Pedal-L Bottle holder End Cap End Cap (K2)Pedal-R (B4) (A44) (H1) (B5) Screw M10 x 55 SCREW M6X10 SCREW M5X12 Washer M10 Tool #13 #14 (M3)
  • Page 3 FIGURE 1 FIGURE 1 - HOW TO ASSEMBLE REAR STABILIZER Attach the rear stabilizer (C) onto main frame by using screw(B4) and washer (B5). USE TOOL: #6 m/m FIGURE 2 FIGURE 2 - HOW TO ASSEMBLE FRONT STABILIZER Attached the front stabilizer (B) onto main frame by using screw(B4) and washer (B5).
  • Page 4 FIGURE 3 FIGURE 3 - HOW TO ASSEMBLE THE HANDLE BAR Step 1: View A shown: Loosen the adjusting knob and pull down the resistance lever. Step 2: View B shown: Pull out the tied wires and locate it along the post. Sliding the handle bar tracking housing onto post and pull the tied wires together.
  • Page 5 FIGURE 4 FIGURE 4 - HOW TO ASSEMBLE CONSOLE Step 1: Attach the console mast (D) at the first hole position and using screw (A44) to tight it. Step 2: Insert the console (L) into console mast(D) and connect the wires together.
  • Page 6 FIGURE 6 FIGURE 6 - HOW TO ASSEMBLE SADDLE Put the saddle (G) onto sliding basement and using tool to tight it. USE TOOL: #13 #14 #15 #17 FIGURE 7 FIGURE 7 - HOW TO ASSEMBLE PEDAL Fix the Right Pedal(screw clockwise) and left Pedal(screw counter-clockwise) to the crank.

  • Page 7: How To Move The Machine

    FIGURE 9 FIGURE 9 - HOW TO MOVE THE MACHINE Hold the handle bar and lift it up until the front transportation wheel touched to the floor, then you can move the machine easily to the place you desire.
  • Page 8 FIGURE 9 FIGURE 9 - HOW TO ADJUST THE HEIGHT OF SADDLE/ HANDLE BAR AND RESISTANCE View A: Loosen the knob firslty and move to the proper position. After that, just tight the knob. It’s the same way for saddle and handle bar position adjustment.
  • Page 10 DESCRIPTION DESCRIPTION MAIN FRAME A46 SLIDE RAILS CHAIN COVER (R) A47 CONSOLE TUBE CHAIN COVER (L) A48 ADJUSTING BOARD FOAM DOUBLE SIDED ADHESIVE A49 DJ JACK CRANK A50 BUSH CRANK CAP A51 HANDLE A52 GENERATOR CONTROL PLATE WASHER A53 SPRING SCREW M4X16 A54 SCREW M5X40 A10 TURING PLATE COVER...
  • Page 11 SCREW WASHER BOTTLE HOUSING REAR BOTTLE HOUSING SCREW ) L ( TRANSPORTATION WHEEL PEDAL ADJUSTED SCREW SCREW SCREW WASHER ADJUSTED CONSOLE SCREW HANDLE SLIDE SCREW...
  • Page 12 How to change battery : 1. Open battery cover and insert 2 AAA or 2 UM-4 batteries. 2. Properly put back battery cover. 3. Under regular condition, warranty of battery is one year. 4. If the LCD shows partial display, please take out batteries, wait for 15 seconds and insert again.
  • Page 13 Functions A.Console functions 1. Scope of application: SPIN BIKE 2. Operating voltage: 3V 3. Main functions: TIME, SPEED, DIST, CAL, RPM, PULSE, LOAD, WATT, PERSONALIZED WORKOUT DATA STORAGE, PERPETUAL CALENDAR, TARGET TIME, TARGET DIST, TARGET CAL, TARGET WATT D. Paired with Battery Mode / Self-generated Electricity Mode / Adopter Mode B.Button functions 1 ENTER/RESET KEY Select TIME / DIST / CAL function...
  • Page 14 Operating Instructions After the power is on, the LCD enters the time setting mode after 1 second. (After this setting, the setting mode will no longer be displayed the next time the power is turned on, unless the batteries are removed or replaced.) A.Time setting mode : YEAR: Range from 2018 to 2099.
  • Page 15 B.TIME Press ENTER KEY and select TIME TARGET mode (The display window in the middle shows ENTER TIME TARGET .) (image6) 1.You can enter value directly instead of pressing UP/DOWN button. 2.Or press UP/DOWN to set the value, ranging from 0:00 to 99:00 (the value increase/ decrease 1:00 with each press)
  • Page 16 D.CALORIES Press ENTER KEY, select CAL TARGET mode (The display window in the middle shows ENTER CALORIES TARGET) (image8) 1.You can enter value directly instead of pressing UP/DOWN button. 2. Or press UP/DOWN to set the value, ranging from 0.0~999.0 (the value increase/decrease with each press) The console’s default mode is counting downward.
  • Page 17 E.TARGET WATT Under STOP mode, press UP or DOWN KEY to enter WATT TARGET mode(image9). You can press UP/DOWN to adjust value. Setting Range is between 100~999W (Default value: 185W)( the value increases/decreases 5W with each press) The console will prompt with an arrow sign whether to increase or decrease or remain the same RPM and LOAD according to the WATT value of the user’s work out.
  • Page 18 Work out data storage function A.After starting up, you need to set the perpetual calendar. B.When the console is paused (image13), press SAVE.DELETE key, the LCD will display SAVE THIS DATA and press ENTER to save the work out data & time & the number of said work out. C.When the console is paused, press RECORDED DATA to pull the work out data.
  • Page 19 A. Press ANT+ to activate the function (the ANT sign will blink 30 seconds after the activation, waiting for the user's heartbeat belt & bracelet to be matched.) B. Pairing with heart rate wristband & heart rate chest belt: The matching should be completed within 30 seconds after the activation of ANT+.
  • Page 20 REMARK A. The bike has to pedal over than 40RPM to power on the console screen. (Example: When pedaling under 40RPM, the console screen is blank.) B.When stop pedaling, the display won’t be shut off until 120 seconds. After 120 sec., the console will enter Sleeping mode which means the display can’t be read.