LDARC TINY R7 Instruction Manual

LDARC TINY R7 Instruction Manual

Original betaflight spracingf3 firmware. support betaflight flip over function. texas instruments drv8850 brush motor driver, 5a continuous 8a peak-drive current each way. motor protocol must use dshot150

Advertisement

Instruction manual
TINY R7
* Original BetaFlight SPRACINGF3 firmware
* Support BetaFlight FLIP OVER function
* Texas Instruments DRV8850 brush motor
driver, 5A continuous 8A peak-drive current
each way
Motor protocol must use DSHOT150
User manual and video please visit:WWW.LDARC.COM
LDARC
TINY R7 Instruction Manual
2018-03-05
9 Pages-Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TINY R7 and is the answer not in the manual?

Questions and answers

Summary of Contents for LDARC TINY R7

  • Page 1 * Support BetaFlight FLIP OVER function * Texas Instruments DRV8850 brush motor driver, 5A continuous 8A peak-drive current each way Motor protocol must use DSHOT150 User manual and video please visit:WWW.LDARC.COM LDARC TINY R7 Instruction Manual 2018-03-05 9 Pages-Page 1...
  • Page 2: Package List

    Carrying case*1 TINY R7*1 Battery*5 TINY R7*1 Battery*1 Charger*1 1-WAY 4.2V/4.35V 3 Canopies TINY meter 1S*1 40mm Prop*6Pairs TINY meter 1S*1 TINY X8*1 (yellow/red/pink) Charger*1 Prop tool*1 Wire(PH2.0)*2 Prop tool*1 Wire(PH2.0)*2 LDARC TINY R7 Instruction Manual 2018-03-05 9 Pages-Page 2...
  • Page 3 2~4S(7~18V) XT60 or USB power input Power by XT60: 1 2 3 4 5 6 WAY Power by USB: 4 5 6 WAY LED ON : Charging LED OFF: Charge finish Molex 1.25 PH 2.0 LDARC TINY R7 Instruction Manual 2018-03-05 9 Pages-Page 3...
  • Page 4 Low power (less than 10%) <F>:5 channel position switch indicator(green LED ARM,red LED DISARM). <J> : RF indicator. <K>:6 channel position switch indicator(fly mode setting, green,yellow,red LED all ANGLE mode default LDARC TINY R7 Instruction Manual 2018-03-05 9 Pages-Page 4...
  • Page 5: Frequency Table

    Q25G2H (25mW 16CH, input voltage 3.6~5.0V) Frequency button Frequency Table Firmware:SPRACINGF3,motor protocol must use DSHOT150. F3-B2 FC BOOT S.BUS/DSM2(UART2) 3.3V 1S BATTERY LDARC TINY R7 Instruction Manual 2018-03-05 9 Pages-Page 5...
  • Page 6: Failsafe Mode

    LED please automatic, LED will blink twice then solid, for reference STATUS LED define above. definitions of LED please reference STATUS LED define above. LDARC TINY R7 Instruction Manual 2018-03-05 9 Pages-Page 6...
  • Page 7 6.Default setting ARM function use AUX1 channel(Picture 5) 7.PID Setting(Picture 6) 3.2.0-SPRACINGF3-29-10-2017 11:00(stable) Picture1 Picture2 ESC/Motor Features DSHOT150 DSHOT150 Picture3 Identifier Configuration/MSP Serial RX UART1 115200 Picture4 UART2 115200 115200 UART3 Picture5 ANGLE LDARC TINY R7 Instruction Manual 2018-03-05 9 Pages-Page 7...
  • Page 8 TINY X8 radio FLIP OVER prog. mix firmware can support one-click automatic flip over TINY X8 radio firmware download WWW.KINGKONG-RC.COM/TX/X8 Product and Factory Code Name Factory Code TINY R7 PNP PNP.TINY R7 BASIC COMBO Basic combo (S-FHSS+D16/FM800/FS-RX2A/DSM2/NO RX) TINY R7 PNP PNP.TINY R7 ADVANCED COMBO Advanced combo...
  • Page 9: After-Sale Service

    Transmitter functions properly Flying in good condition Camera OK Frame VTX OK Transmitter ID is the same All parts of the installation Insulating sleeves have been installed manual Complete accessories,total packages LDARC TINY R7 Instruction Manual 2018-03-05 9 Pages-Page 9...

Table of Contents