Table of Contents
Advertisement
Description of other Functions, Method for Setting These Functions
Preset Time/ Schedule
• The Pre-set Schedule Time is the Program end time.
• Before making a Schedule, first turn on the Faucet, and then lay down the Drain
Hose and check whether the Universal Joint is tightened to avoid water leakage
accidents.
Operation Steps
1. Close the Washer Lid.
2. Put the laundry in the Drum and close the Washer Lid.
3. Choose the appropriate Program, procedures and water level needed.
4. Press the Preset Time Button to set the Schedule Time.
• Preset Time Time Options Displayed:
5. Add detergent.
• Detergent Addition for a Preset Time: Add detergent, powder detergent and
softener to the corresponding boxes.
6. Press the Start/Pause Button
• All the Indicators except the Preset Time Indicator and the 6 Sense Smart Slider
Indicator will go out in about one minute. (If the Child Lock Function is enabled,
the corresponding Child Lock Indicator will be lit)
• The Preset Time/ Schedule Function is unavailable for the 6 Sense One Key
Smart Select Program.
• If you want to check the Preset/ Scheduled Program, please press any Button
other than the Power Button. The Preset/ Scheduled Program will be displayed for
several seconds.
• To change the Preset/ Scheduled Program, turn off the power and then restart the
Machine and carry out the resetting.
• The Preset Time Program will be disabled if the Power Cord Plug is unplugged or
a power failure occurs.
Smart Memory Function
If you choose the Mix Wash, Cotton Wash, or 6 Sense Smart Program the
Washing Machine will remember your choice after the Program ends. When turning
on the Machine the next time, you can just press the Start/Pause Button to start the
remembered Program.
• Wash Parameters are remembered only for the 6 Sense Smart Program but not
for the Mixed Wash or Cotton Wash Program.
• The Child Lock and ADS will also remember its last settings.
Two-step Clean Function
During the washing process, after the water level of the washing machine reaches
the level that is two levels lower than the pre-set water level, the wash will start
while water continues to flow in.
• When the two lowest levels are set, the wash will start after the pre-set water
levels are reached.
• The Two-step Clean Function is unavailable for the Wool Wash, Textiles Wash,
Quick Wash, Warm Wash, Rinse+Spin and Spin Dry Programs
• If the Super Soak Program is chosen, after the soak ends, the Two-step Clean
Function will be disabled during the wash.
(hours)
t h
t h
t h
t h
Description of other Functions, Method for Setting These Functions
Variable Wave Function
After this function is enabled, the washing or rinsing strength can be changed.
This function can be enabled before a Program starts or while a Program is
running. (this function is unavailable for Wool Wash, Down Wash,
Warm wash, Spin Dry and Tub Clean.)
Water Level (Varied Wash) Function
In order to improve the detergent content in the washing water and save water,
you can set different water levels for a wash and rinse respectively. It is
recommended that the wash proceeds at a lower water level and the rinse at a
higher water level. In this way, a clean wash and a thorough rinse can be ensured.
Setting Method
Press the Power Button to turn on the power. After selecting the appropriate
Program, press the Wash Button to set the washing time, press the Water Level
Button to set the wash water level, press the Rinse Button to set the rinsing times,
press the Water Level Button again to set the rinsing water level, press the Spin-
drying Button to set the spin-drying time, and finally, press the Start/Pause
Button to start. Then the wash and rinse will proceed at different pre-set water
levels.
Tub Light Function
Press the Power Button to turn on the power. The Tub Light will be lit when the
Washer Lid is opened and will go out 2 minutes after the Washer Lid is closed.
The Tub Light will go out automatically 3 minutes after the Washer Lid is not
closed.
• You can press and hold the Quick Wash for 3 seconds to turn on or turn off the
Tub Light.
Super Soak Function
After the Super Soak Function is enabled, a dynamic soak can be added
before a wash (this function is unavailable for Wool Wash, Quick, Warm Wash,
Rinse+Spin, Spin Dry and Tub Clean.) The soaking time is
0 - 40 minutes with an increment of 10 minutes.
Energy-saving Function
This function is enabled by default in the factory settings. Once enabled, the
backlight will automatically go off after 30 seconds of inactivity upon switching on
the machine. All the indicators except the 6th Sense Smart Slider and Child Lock
indicator will go out and be locked. If a program has been chosen, the backlight of
the programs will stay lit for 10 seconds and automatically go off after. When any
button other than the Power Button is pressed and held for 2 seconds, you will
hear a beep, and the Backlight will be turned on and the Buttons will be unlocked.
Press and hold the Wash Button for 4 seconds until you hear a beep, and the
Automatic Button Lock Function will be enabled. When you want to disable the
function, repeat the above steps until you hear a beep, and the function will be
disabled.
Hide quick links:
Advertisement
Table of Contents
