Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for BENE T-Meeting
Summary of Contents for BENE T-Meeting
- Page 1 LIFT DESK. T-MEETING SAFETY AND OPERATING INSTRUCTIONS NOTE Please read all instructions carefully before operating the system. Keep instruction manualfor further reference. This document is alternative available on the official Bene - homepage. (www.bene.com)
-
Page 2: Table Of Contents
CONTENTS Contents ..............2 Product overview ............3 Safety instructions ............. 4 Sitting correctly ............8 Declaration of conformity ..........9 Manual control. General information ......10 Manual control. Saving a table top position ....11 Manual control. Adjusting the height display of the table top position ......... -
Page 3: Product Overview
PRODUCT OVERVIEW STANDARD TABLE SIZES: 2000/1100 2200/1100 2400/1200 TABLETOP OPTIONS: rectangular rounded oval boat-shaped rectangular... -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS Please observe the safety instructions! 6. Make sure adjacent objects are placed at Improper operation of the system may a minimum distance of 25 mm to prevent result in personal injury and cause them from being squeezed or sheared! damage to objects! 7. - Page 5 SAFETY INSTRUCTIONS 10. Do not change or modify the control they are supervised by a person mechanism or the operating device. responsible for their safety or received instructions about how to use the appli- 11. Never open the enclosure of the control ance.
- Page 6 SAFETY INSTRUCTIONS 19. Furniture with flexible or height-adjustable 22. The operation of the control mechanism components require special care. Cables and the power supply unit requires a must be sufficiently long to allow height minimum of 5°C and a maximum adjustments without damaging the cables temperature of 40°C.
- Page 7 SAFETY INSTRUCTIONS Warning: In the event of a fault it is After 2 minutes of continuous operation possible that the table top moves a bit the system automatically shuts itself off during every attempt whilst operating and cannot be used for an additional before the safety switch off kicks in.
-
Page 8: Sitting Correctly
SITTING CORRECTLY 200% > 600 mm 140% 20° 100% > 100 mm 90-100° Sitting with a hunched back doubles the burden (200%) on 90-100° the vertebral disks compared to standing up (100%). Occupational health experts have issued standards and recommendations for preventing harmful habits and their negative health impact at the office workplace. -
Page 9: Declaration Of Conformity
DECLARATION OF CONFORMITY... -
Page 10: Manual Control. General Information
MANUAL CONTROL. GENERAL INFORMATION "LIGHT" MANUAL CONTROL Raise table top Lower table top "PRO" MANUAL CONTROL Ergoflex Pedestal Info Reset Container Ergo ex Reset Info Raise table top - 2. Motor group Raise table top Lower table top - 2. Motor group Lower table top Memory position buttons 1-4 Memory button... -
Page 11: Manual Control. Saving A Table Top Position
MANUAL CONTROL. SAVING A TABLE TOP POSITION Container Ergo ex Reset Info Container Ergo ex Reset Info This function saves a defined table top height. 3. Press the desired memory button (1-4) Note: When the motor control is used for the first time, all of the saved positions are equal to the lowest table top height (lowest position) The display will read S 2. -
Page 12: Manual Control. Adjusting The Height Display Of The Table Top Position
MANUAL CONTROL. ADJUSTING THE HEIGHT DISPLAY OF THE TABLE TOP POSITION Container Ergo ex Reset Info This function shows the height on the display without moving The display will begin to blink. the table top. Note: When the motor control is used for the first time, all of the saved positions are equal to the lowest table top height (lowest position) Container... -
Page 13: Manual Control. Manual Reset
MANUAL CONTROL. MANUAL RESET Container Ergo ex Reset Info If the actual table top position no longer agrees with the table "LIGHT" MANUAL CONTROL top position displayed, then it needs to be reset. 2.1 Simultaneously press and hold the “lower table top” and “raise table top”... -
Page 14: Manual Control. Keylock
MANUAL CONTROL. KEYLOCK Container Ergo ex Reset Info The keylock prevents the motor controls from accidental in- UNLOCK puts via the manual control. Press the S button and then press the Container Ergo ex Container Ergo Reset Info Reset Info LOCK “lower table top - 2nd motor group”... -
Page 15: Manual Control. Pedestal-Stop - Shelf-Stop
MANUAL CONTROL. PEDESTAL-STOP – SHELF-STOP Container Ergo ex Reset Info These two features can be used to limit the table’s range "PRO" MANUAL CONTROL Container Ergo ex Reset Info of movement (e.g. if a pedestal is located under the table). Press the S button. -
Page 16: Manual Control. Pedestal-Stop - Shelf-Stop/Changing Display From Cm To Inches
MANUAL CONTROL. PEDESTAL-STOP – SHELF-STOP/CHANGING DISPLAY FROM CM TO INCHES Container Ergo ex Container Ergo ex Reset Info Reset Info Pedestal-stop – Shelf-stop Changing display from cm to inches DEACTIVATE POSITION 1. Simultaneously press the memory position buttons 1 and 2, as well as the “raise table top”... -
Page 17: Manual Control. Reset To Factory Defaults
MANUAL CONTROL. RESET TO FACTORY DEFAULTS Container Ergo ex Reset Info Container Ergo ex Reset Info 1. Simultaneously press the memory position buttons 1 and 3. Press the memory button Container Container Ergo ex Ergo ex 2, as well as the “raise table top” button. Reset Reset Info... -
Page 18: Manual Control. Error Messages On The Manual Controller Display
MANUAL CONTROL. ERROR MESSAGES ON THE MANUAL CONTROLLER DISPLAY Container Ergo ex Reset Info 1. MOTORS NOT WORKING Display DESCRIPTION SOLUTION 1a. Power cable is not plugged in 1. Plug in the motor controller power cable Internal error channel 1 2. - Page 19 MANUAL CONTROL. ERROR MESSAGES ON THE MANUAL CONTROLLER DISPLAY Plug detection on motor M1 connector Plug detection on motor M2 connector 1. Plug the correct motor to the affected connector Plug detection on motor M3 connector Motor exchanged Synchronisation of motor group 1 not pos- 2.
- Page 20 MANUAL CONTROL. ERROR MESSAGES ON THE MANUAL CONTROLLER DISPLAY Reset was not completed 1. Unplug the motor control and wait for at least 5 seconds Defective drive (The signal level for 2. Take the motor control back into operation the transmission to the control is 3.
-
Page 21: Manual Control. Click Codes
MANUAL CONTROL. CLICK CODES As soon as the controller is supplied with power, the controller uses its built-in relays to audibly inform the user about the system status. The following table shows the correlation between the number of clicks and what they mean. NUMBER OF CLICKS STATUS INFORMATION Normal operating mode:... -
Page 22: Levelling. Reset
LEVELLING. RESET A reset must be done when the table is used for the first time in order to operate the product. For a table, the reset causes all of the columns to be brought to the same level in the table’s lowest position. This ensures that the table top is positioned parallel with the ground. -
Page 23: Technical Data
TECHNICAL DATA Maximum load........100 kg Input power (reference values) including PC, PC holder, printer extensions, table panel etc.! Load Power consumption Stand-by ......0-100kg ....0,5 watts/h Control type CBC-KB-3-BA-EU Upward lift ......0kg ..... 141,0 watts/lift Input power supply ..... 230V ~50Hz 5AA Upward lift ...... -
Page 24: Cleaning Instructions. Certificates
An enhanced glossy appearance of DISPOSAL the surface is difficult to prevent. Never use polishes Instructions for the disposal of Bene products can be found in containing silicon, caustic cleaning agents with ammonia the sustainability report at: http://www.bene.com... -
Page 25: Notes
NOTES .............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................. - Page 26 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
- Page 27 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
- Page 28 Bene plays a leading role in responsible environmental management. It is practiced throughout all company divisions -from product development, procurement, production and logistics to product recycling. Bene considers ecology to be a central element of its responsible and stable corporate strategy. Bene sees the legal regulations as minimum requirements and strives for better and more sustainable environmental protection throughout the group.
Need help?
Do you have a question about the T-Meeting and is the answer not in the manual?
Questions and answers