Page 1
SILVERSHINE – THE CUTLERY DRYING MACHINE Models CDM12K, CDM6K, CDMStar OPERATING INSTRUCTIONS IMPORTANT FILL OUT and RETURN ENCLOSED PRODUCT REGISTRATION WARRANTY CARD Sales & Service 2871 Brighton Road, Oakville, Ont. L6H 6C9 (866) 912-3469 www.cpishine.com Rev: Jan 2015...
Page 3
LIMITED WARRANTY Campus Products, Inc. (“CPI”) warrants to the original purchaser that any original part that is found to be defective in material or workmanship will, at our option, subject to provisions hereinafter stated, be replaced with a new or rebuilt part.
Page 5
Campus Products Inc. (866) 912-3469 www.cpishine.com ORDER FORM BILLING ADDRESS (please print): SHIP TO (if different than billing address): Name: ________________________________________ Name: ________________________________________ Address: ______________________________________ Address: ______________________________________ _______________________________________________ _______________________________________________ City: __________________________________________ City: __________________________________________ Zip/Postal Code: ________________________________ Zip/Postal Code: ________________________________ Daytime phone: ________________________________ Daytime phone: ________________________________ Fax Number: ___________________________________ Fax Number: ___________________________________...
TABLE OF CONTENTS OVERVIEW FOR SILVERSHINE – THE CUTLERY DRYING MACHINE ......3 WHAT THE MACHINE IS DESIGNED TO DO ....................3 HOW THE MACHINE WORKS ........................4 TECHNICAL FEATURES ..........................5 INSTALLATION INSTRUCTIONS ..................6 ...
OVERVIEW FOR SILVERSHINE – THE CUTLERY DRYING MACHINE WHAT THE MACHINE IS DESIGNED TO DO … dry, sanitize and polish cutlery. All restaurants have the labor intensive job of hand drying and polishing cutlery to try to remove the scale marks. Whether the metal is stainless steel or silver, the problem remains the same –...
Silvershine – The Cutlery Drying Machine is available in four model sizes; CDM Star, CDM2K, CDM6K, and CDM12K – each model provides a different cutlery drying / sanitizing capacity. The CDM Star is a table top unit, all other models are positioned on the floor.
TECHNICAL FEATURES CDM6K CDM12K Model CDMStar CDM2K 6.25 Amps 1200 1300 Watts 1200 22 X 17 X 19 18 X 22 X 20 22 X 27 X 32 26 X 32 X 32 Dimensions (W X D X H) Volts Weight ( lbs.)
INSTALLATION INSTRUCTIONS POSITIONING THE CUTLERY DRYER: FLOOR MODELS The dryer does not need to be anchored to the ground, but it must be positioned so that the four legs rest firmly on the ground. Adjust the nuts on the legs to level the unit, if necessary.
FILLING THE TANK WITH GRANULATE Place the drying material inside the “Nautilus” tub as follows: Switch on the machine by lifting the stainless steel lid and pressing the Main Power switch. Press the “Start” icon located on the front control panel of the Silvershine. Gently close the lid.
HOW TO OPERATE THE MACHINE THE CONTROL PANEL Control Panel MODEL CDM 12K shown There are only 2 controls on the cutlery dryer. 1. On/Off power switch Digital Temperature Regulator – The cutlery dryer is equipped with a digital temperature regulator that controls the temperature of the machine. temperature indicated on the display is factory set and MUST NOT BE ALTERED.
HOW TO SWITCH ON THE MACHINE For your Silvershine machine to perform at peak efficiency, the granulate must be warmed to properly dry the cutlery. Therefore the dryer needs to be switched on at least 20-30 minutes before use to preheat the granulate until the thermoregulator reads approx. 125°°F .
OPERATING TIPS Be sure the unit is as level as possible. If the floor is not level, it is better to have the unit tilt slightly from left to right rather than right to left. Always be sure to lock the front two (2) castors in place to ensure the unit stays stationary during operation.
TROUBLESHOOTING REPAIR TIPS: 1. Motor and interior access is easier from the RIGHT side of the unit with the unit lying on its left side. 2. Most troubleshooting can be performed with the front panel OFF allowing for access to the control panel/circuit board compartment.
Page 16
UV Lamp is not on Lamp has burned out Remove four screws on the shroud housing the UV lamp, check that the lamp has not burned out. Replace lamp if necessary Lamp ballast has no power ...
MAINTENANCE INSTRUCTIONS INTRODUCTION: If this machine is installed and operated properly, it will provide lengthy trouble-free operation without requiring any particular maintenance. However, for the machine to operate efficiently, it is vital to clean it frequently and carry out the following routine check There two basic types of maintenance: GENERAL MAINTENANCE, which can be done by the user.
GENERAL MAINTENANCE REPLACING THE GRANULATE: When the drying material becomes very powdery and is noticeable on your cutlery, or very dirty due to pieces of food not being removed during the washing process, it must be replaced. Used under normal conditions, i.e. 1 or 2 hours a day, the granulate needs to be changed every 90-120 days. To do this, proceed as follows: ...
REGULAR CLEANING: he vibration motor is self-lubricating and does not require any maintenance. It is necessary to clean the inside of the unit on a regular basis for hygienic reasons and to clear the fan intake. Proceed as follows: Remove the plug from the power socket.
EXTRAORDINARY MAINTENANCE This must only be done by a qualified service engineer. Since there are so few parts to the Silvershine, replacing faulty components is an extremely rare occurrence. The most common components that may require changing are the UV-C lamp and a fuse.
HOW TO REPLACE THE UV-C LAMP UV-C Lamp Tank Cover Screws Stainless Steel Tank Cover To replace the UV-C lamp proceed as follows: 1. Remove the plug from the power socket. 2. Ensure that the UV-C lamp has cooled down before changing the lamp 3.
Page 22
Electric cord clips 5. Using the appropriate screwdriver, remove the clips that secure the electric cord to the unit. 6. Remove the four screws that affix the stainless steel cover of the UV-C lamp to the Silvershine unit. 7. Leaving the sponge in place in the UV-C cavity, gently remove the lamp from the ballast and replace with the new UV-C lamp.
HOW TO REPLACE THE FUSE: Stemshine is outfitted with a fuse to protect against overload. If the fuse blows, the machine will not switch on and the light on the Main Switch (1) will not illuminate. If this happens, proceed as follows: 1.
HANDLING AND TRANSPORT The machine must be transported using a transpallet on a flat smooth surface (see Fig 10). The total weight of the machine is 190 kg. CPICDMOPINST Page - 20 SALES + SERVICE (905) 829-2355 www.cpishine.com...
EXPLODED PARTS DIAGRAM – CDM 6K Part # Description Part # Description Part # Description Stainless steel tank Complete Spring Wheel without brake Motor complete Wheel with brake Exit sign holder Thermostat Plastic Chute Plastic Lid Heating Element Frame Tank Frame Lamp holder Entry Frame Basket with holes...
Page 26
Parts layout prior to S/N 11.7021 Update: 28-July-10 Page 1 of 5...
LIST OF MATERIALS DETAIL OF ELECTRICAL PANEL N° DESCRIPTION CDM 6K CDM 12K PLASTIC LID PLASTIC LID FRAME STAINLESS STEEL COVER TANK COVER + LAMP COVER ENTRY FRAME REAR GRID FRONT GRID TANK COMPLETE SPRING 1082 MOTOR-VIBRATOR STAINLESS STEEL ELECTRIC PANEL CHUTE PERFORATED SIDE PANEL - LEFT N.B.
Page 28
EXPLODED PARTS DIAGRAM – CDM STAR Diag # Part # Description Diag # Part # Description Stainless steel lid motor UV lamp side panel rubber cap Complete spring stainless steel hinge ballast Lamp Holder Temperature Control limit switch and cable light switch (Power) Grid Protection capacitor...