Advertisement
Quick Links
HDWH2 & HDWH4
Wire Harness Installation
HDWH2 Fit Guide- 1998-2013 (Ultra Classic, Electra Glide, Street Glide, and Tri Glide)
Bracket fits- 1998-2013 (Road Glide and Road Glide Ultra)
Not for CVO Models
Contents:
1. MTX Wiring Harness- Includes all connectors for connecting to
MTX MUD amplifier and speakers.
2. Hook and loop fastener Pad
3. Speaker Adaptor Rings-2
Installation Tools:
Wrenches/Sockets-
⁄
",
⁄
",
⁄
", 10mm
7
3
1
16
8
2
Torx Driver- T10, T25, T40
#2 Phillips Screw Driver
"Wiring Diagram"- shows the overall wire harness attached to the MUD amp and
battery in the bike.
Installation:
Please note if you are unsure about disassembling your motorcycle please have
this installed by a qualified technician.
Clutch
ULTRA CLASSIC, ELECTRA GLIDE, STREET GLIDE AND TRI GLIDE INSTALLATIONS
Please go to page 3 for Road Glide and Road Glide Ultra installation.
First Step - Remove the Fairing
A- Remove the top bolts on the bottom of the windshield. After the bolts are
removed, carefully remove the windshield.
B- Remove the screws on the bottom sides of the fairing. This will allow the
fairing to be removed.
C- Pull the fairing forward and up slightly, the harness connecting the headlight
will need to be removed to completely pull the fairing away from the bike.
a. Be careful to not bump the fairing against the signal lights or other
Second Step - Remove Existing Speakers
A- Pull the speaker wire connectors from the speakers, take care to pull them
from the plastic connector and not the wires so that the stock wire harness
is not damaged.
B- Use a Torx driver to loosen the 4 screws holding on the stock speakers.
Brake
C- Keep track of which wires go to the clutch and brake side speakers.
D- The speaker grill assembly needs to be removed from the stock speaker,
make sure to keep it in a safe place or remember its orientation. This will be
important for mounting the new speakers in place.
installed lights connected to the front fork. A sock or other fabric can
be used to protect the side lights during fairing removal.
Advertisement
Summary of Contents for MTX HDWH2
- Page 1 HDWH2 & HDWH4 Wire Harness Installation HDWH2 Fit Guide- 1998-2013 (Ultra Classic, Electra Glide, Street Glide, and Tri Glide) ULTRA CLASSIC, ELECTRA GLIDE, STREET GLIDE AND TRI GLIDE INSTALLATIONS Bracket fits- 1998-2013 (Road Glide and Road Glide Ultra) Please go to page 3 for Road Glide and Road Glide Ultra installation.
- Page 2 A- Connect the MTX wire harness to the factory speaker wiring, making sure the clutch side and brake side are connected to the correct input wires. The wires are marked with a tag on each end. Plug the MTX harness connectors into the corresponding factory connectors. Please ensure the connections are secure so they do not come loose when riding.
- Page 3 C- Unplug the stock wire connected to the center of the cigarette lighter. Then ROAD GLIDE AND ROAD GLIDE ULTRA INSTALLATION plug in the blue wire from the MTX wire harness into the cigarette lighter, and First Step - Remove the Fairing then plug the stock cigarette lighter wire connector into the extra connector A- Remove the 6 bolts on the bottom side of the fairing.
- Page 4 C- Unplug the stock wire connected to the center of the cigarette lighter. Then plug in the blue wire from the MTX wire harness into the cigarette lighter, and then plug the stock cigarette lighter wire connector into the extra connector on the MTX wire harness.
- Page 5 D- If the MUD amp included with your kit has a High Level switch, move the J- Open fuse holder and place the 15 amp fuse in the holder. switch to Low Level. The MTX harness converts the signal to low level to correctly work with the MUD amplifier.
- Page 6 First Step - Remove the Fairing Contents: A- Remove the top bolts on the bottom of the windshield. After the bolts are 1. MTX Wiring Harness- Includes all connectors for connecting to removed remove the windshield carefully. MTX MUD amplifier and speakers.
- Page 7 A- Connect the MTX wire harness to the factory speaker wiring, making sure the clutch side and brake side are connected to the correct input wires. The wires are marked with a tag on each end. Plug the MTX harness connectors into the corresponding factory connectors. Please ensure the connections are secure so they do not come loose when riding.
- Page 8 C- Unplug the stock wire connected to the center of the cigarette lighter. Then B- Remove the right and left turn signals. plug in the blue wire from the MTX wire harness into the cigarette lighter, and then plug the stock cigarette lighter wire connector into the extra connector on the MTX wire harness.
- Page 9 A- Connect the MTX wire harness to the factory speaker wiring, making sure the clutch side and brake side are connected to the correct input wires. The wires are marked with a tag on each end. Plug the MTX harness connectors into the corresponding factory connectors. Please ensure the connections are secure so they do not come loose when riding.
- Page 10 C- Unplug the stock wire connected to the center of the cigarette lighter. Then plug in the blue wire from the MTX wire harness into the cigarette lighter, and then plug the stock cigarette lighter wire connector into the extra connector on the MTX wire harness.