Setting the DHW Times Mode Selection/Temp Adjustment Contents of Other Functions Resetting the Boiler 10.0 Clearance 11.0 Error Codes 12.0 Care of the boiler 13.0 Legislation 14.0 Notes Boiler Controls - see opposite page for Operating Quick Reference Guide Page...
Programmable Operator Unit (POU) 24 hour time bar for central heating and domestic hot water - shows active programme times - Default 6am - 9am, 11am - 12pm & 15pm - 22pm 04. November 2008 Tuesday Easy Menu Button Dial Knob (Turn /Push Select) Text 1 Text 2 Text 3...
Baxi Ecogen which will generate electricity. This is a legal requirement. 6. Operation and control is similar to a domestic boiler and is fully automatic. 7. All interactions with the appliance are either through the removable Programmable Operator Unit (POU) on the front of the appliance or on a remote wall cradle.
4. Refer to the instructions for the existing programmers for setting the timed periods and the room temperatures. The programmable operating unit will display the boiler flow temperature and any errors see section 9 onwards. POU as a Programmable Room Unit (PRU) 1.
04. November 2008 08:50 Tuesday Menu Button Dial Knob STEP 1 The basic display is shown. If the basic display is not showing, press the MENU button. until the 04. November basic display is shown Tuesday STEP 3 Turn the Dial Knob clockwise to highlight ‘Set Time and Date’.
04. November 2008 08:50 Tuesday Menu Button Dial Knob STEP 1 The basic display is shown. If the basic display is not showing, press the MENU button. until the 04. November basic display is shown Tuesday STEP 3 Turn the Dial Knob clockwise to highlight ‘Time central heating CH1’.
Page 8
04. November 2008 08:50 Tuesday Menu Button Easy Menu Dial Knob Button STEP 9 Press the Dial Knob and the ‘1st Time ON’ time will flash. Turn the Dial Knob to the required time. Press Dial to select. Time central heating CH1 Mon - Sun: 1st Time ON STEP 11 Turn the Dial Knob one click...
04. November 2008 08:50 Tuesday Menu Button Dial Knob STEP 1 1. The basic display is shown. If the basic display is not showing, press the MENU button. 04. November Tuesday STEP 3 Turn the Dial Knob clockwise to highlight ‘Time hot water’. Time central heating CH1 Holidays heating CH1 STEP 5...
Page 10
04. November 2008 08:50 Tuesday Menu Button Easy Menu Dial Knob Button STEP 9 Press the Dial Knob and the ‘1st Time ON’ time will flash. Turn the Dial Knob to the required time. Press Dial to select. Mon - Sun: 1st Time ON STEP 11 Turn the Dial Knob one click clockwise.
04. November 2008 08:50 Tuesday Menu Button Easy Menu Dial Knob Button STEP 1 The basic display is shown. If the basic display is not showing, press the MENU button. until the basic display is shown STEP 2 Press the MENU button. STEP 3 Turn the Dial Knob clockwise to highlight ‘Temps / mode CH1’.
Page 12
04. November 2008 08:50 Tuesday Menu Button Easy Menu Dial Knob Button DOMESTIC HOT WATER MODE STEP 1 - Press the MENU button turn the Dial Knob clockwise to highlight ‘Domestic hot water’. Temps / mode CH1 Temps / mode hot water Diagnostics engine STEP 2 - Press the Dial Knob to select .
Page 13
04. November 2008 08:50 Tuesday Menu Button Easy Menu Dial Knob Button STEP 1 - Press the MENU button. HOLIDAY MODE Time hot water Holidays heating CH1 Temps / mode CH1 STEP 2 - Turn the Dial Knob to highlight ‘Holidays heating CH1’...
‘information’ by pressing the Dial Knob, any error is displayed first then : - 1. Room temperature – ?C (PRU only). 2. Boiler temperature – ?C. 3. State burner – 1+2 (1=engine, 2= supplementary burner on). 4. Power – Watts.
08:50 Tuesday Reset Type Auto User Service Error 164:Flow press switch HC Error 157: Boiler flow thermostat Reset ? Error 157: Boiler flow thermostat Reset ? Error 266:Fan Fault 9.0 Resetting the Boiler Exceptional conditions 1. In exceptional cases, the display will show an error screen see diagram opposite.
Left side Right Side Front 200mm Min 7. If your boiler is installed in a compartment, do not use it for storage purposes. Do not obstruct any purpose provided ventilation openings. 8. Flammable materials must not be stored in close proximity to your boiler.
Failure in EGC-SW which causes non-volatile lock. 127: Legionella temperature Legionella temperature not achieved within 48 hours 157: Boiler Flow Overheat stat Boiler flow overheat thermostat / safety chain open 158: Condensate Condensate switch of safety chain opened 164: Flow...
Page 19
UR = User Reset, AR = Automatic Reset, ARP = Automatic Reset after Power Down NOTE: An automatic reset is only done if the fault condition has cleared. Error code: Display Description 280 : Engine dome overtemp Engine dome overtemp has operated 282: G83/ENS/G1M G83/ENS module has detected an unhealthy mains condition 285: Alternator Short...
1 minute if it has not run in the last 24 hours. 12.5 View from under appliance 1. If a fault occurs on the boiler an error code may be shown on the facia display. 12.6 If a gas leak occurs or is suspected, the boiler can be isolated at the inlet valves as follows;...
0800 408 5500 or online at www.GasSafeRegister.co.uk The boiler meets the requirements of Statutory Instrument “The Boiler (Efficiency) Regulations 1993 No 3083” and is deemed to meet the requirements of Directive 92/42/EEC on the energy efficiency requirements for new hot water boilers...
Page 24
Please complete the boxes below Serial Number Date of Installation D D M Installer Details (name, address and contact number(s)) Information Label All descriptions and illustrations provided in this leaflet have been carefully prepared but we reserve the right to make changes and improvements in our products which may affect the accuracy of the information contained in this leaflet.