ZURN Siera Z7440 Series Installation, Maintenance Instructions And Replacement Kits

Z7440 Series Single Handle Lavatory Faucet
With Adjustable Temperature Limit Stop

Installation

SIERRA FAUCET PARTS
ITEM PART NO.
1 RK7440-LH
RK7440-LH-STN LEVER HANDLE, SATIN NICKEL
2 RK7440-LP
RK7440-LP-STN LOOP HANDEL, SATIN NICKEL
RK7440-3
3
RK7440-3-STN RETAINING NUT, SATIN NICKEL
4 RK7440-CART
RK7440-94
RK7440-94-STN
AERATOR SPRAY OUTLET
RK7440-94SO
7440-94LA
5
7440-94VP/WK
RK7440-94-VP1.5
7440-94FC/WK
6 RK7440-90
7 RK7440-17
8 RK7440-HK
9 RK7440-36W

Maintenance Instructions

DESCRIPTION QTY
LEVER HANDLE 1
1
LOOP HANDLE 1
1
RETAINING NUT ASSY.
RETAINING NUT 1
RETAINING GASKET 1
ESCUTCHEON 1
RETAINING NUT ASSY.
1
RETAINING GASKET 1
ESCUTCHEON 1
CARTRIDGE ASSEMBLY 1
W/ LIMIT STOP
AERATOR, STD 2.2 GPM
AERATOR 1
WASHER 1
AERATOR, SATIN NICKEL 1
STD. 2.2 GPM
AERATOR 1
WASHER 1
1.0 GPM
AERATOR 1
WASHER 1
AERATOR, LAMINAR
FLOW, 2.2 GPM
AERATOR 1
WASHER 1
AERATOR, VANDAL
PROOF 2.2 GPM
AERATOR 1
WASHER 1
KEY 1
AERATOR, VANDAL
PROOF 1.5 GPM
AERATOR 1
WASHER 1
KEY 1
AERATOR, FLOW
CONTROL 0.5 GPM
AERATOR 1
WASHER 1
KEY 1
BASE PLATE 1
MOUNTING BRACKET
ASSY.
BRACKET 2
HEX NUT 2
INLET NUTS 2
SPOUT ASSY.
SPOUT GASKET 1
WATERWAY SPOUT 1
AERATOR WASHER 1

Replacement Kits

CONGRATULATIONS
You have purchased a ZURN Quality Manufactured lavatory fau-
cet that contains a "life of the system" ceramic cartridge. The
Sierra faucet will provide you with years of trouble free service.
If you should have any questions, please contact your local
ZURN/TEMP-GARD representative or the factory at the address
on the back of this sheet.
INSTALLATION INSTRUCTIONS
1. Shut off hot and cold water supplies.
2. Place faucet base plate on faucet and position on lavatory
sink. In some installations, a sealant may be required to
make a water tight seal between the faucet base plate and
the mounting surface. The installer should verify the
compatibility of the selected sealant with the mounting
surface manufacturer. Both plumber's putty and silicone
sealants are compatible with Zurn faucets and fixtures.
Consult the mounting surface manufacture for their
recommendation of sealant. From underneath the sink,
position bracket on mounting studs and attach the hex nuts.
Tighten hex nuts.
3. If faucet includes pop-up or grid drain, refer to next
page for pop-up assembly installation.
4. Connect left inlet tube to hot water supply and right inlet
tube to cold water supply. CAUTION: Care should be taken
not to kink tubes when connecting to water supplies.
*
ANY SIERRA FAUCETS INSTALLED PRIOR TO 3-1-05 SHOULD
ADD - OS SUFFIX TO ALL REPAIR KIT PART NUMBERS
CAUTION: DO NOT APPLY SOLDER OR BRAZE TO INLET
TUBES. EXCESSIVE HEAT MAY DAMGE COMPONENTS OF THE
SIERRA FAUCET!
CF952
Form #
128418
C.N. No.
12/16/11 IS7440
Date: Product No.:
i
Rev. Sheet 1 of 4