Hatco THERMO-FINISHER TFC-461R Installation And Operating Manual
  1. Manuals
  2. Brands
  3. Hatco Manuals
  4. Finishers
  5. THERMO-FINISHER TFC-461R
  6. Installation and operating manual
Hatco THERMO-FINISHER TFC-461R Installation And Operating Manual

Hatco THERMO-FINISHER TFC-461R Installation And Operating Manual

Tfc-461r series, conveyor food finisher
Hide thumbs Also See for THERMO-FINISHER TFC-461R:
Table of Contents

Advertisement

Quick Links

THERMO-FINISHER
Conveyor Food Finisher
Do not operate this equipment unless you
have read and understood the contents of
this
manual!
Failure
instructions contained in this manual may
result in serious injury. This manual
contains important safety information
concerning the maintenance, use, and
operation of this product. If you're unable
to understand the contents of this manual,
please bring it to the attention of your
supervisor.
Keep this manual in a safe
location for future reference.
TFC-461R Series
Installation and
Operating Manual
I & W #07.05.149.00
to
follow
the
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en este
manual puede resultar en un serio daño.
Este
manual
contiene
información
sobre
concerniente al mantenimiento, uso y
operación de este producto. Si usted no
puede entender el contenido de este
manual
por
favor
supervisor. Almacenar este manual en una
localización segura para la referencia
futura.
™
importante
seguridad
pregunte
a
su
© 2007 Hatco Corporation

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the THERMO-FINISHER TFC-461R and is the answer not in the manual?

Questions and answers

Related Manuals for Hatco THERMO-FINISHER TFC-461R

Summary of Contents for Hatco THERMO-FINISHER TFC-461R

  • Page 1 Keep this manual in a safe manual favor pregunte location for future reference. supervisor. Almacenar este manual en una localización segura para la referencia futura. © 2007 Hatco Corporation...

  • Page 2: Table Of Contents

    Additional information can be found by visiting our web site at www.hatcocorp.com. INTRODUCTION The Hatco Thermo-Finisher conveyor food finisher or operation of the Thermo-Finisher. Safety is designed to rapidly heat or thermalize a wide instructions that appear in this manual after a safety...

  • Page 3: Important Safety Information

    (305 mm) from the ceiling. not have the characteristics that will allow them to operate safely in Hatco equipment. To ensure proper operation and safety, It is essential to use Genuine Hatco allow a minimum of 1″ (25 mm) clearance Replacement Parts when repairing Hatco along the rear of the unit and 2″...

  • Page 4: Model Designation

    IMPORTANT SAFETY INFORMATION IMPORTANT! Read the following important safety information to avoid personal injury or death, and to avoid damage to the equipment or property. CAUTION CAUTION Unit is not weatherproof. For safe and Do not remove the glass from the unit for proper operation, locate the unit indoors cleaning purposes.

  • Page 5: Model Descriptions

    For safe and proper operation, plug unit into a NEMA L15-30P NEMA 6-50P properly grounded electrical outlet NOTE: Receptacle not supplied by Hatco. correct voltage, size, plug configuration. If the plug and receptacle do not match, contact a qualified electrician to Figure 3.

  • Page 6: Dimensions

    SPECIFICATIONS DIMENSIONS EXTERIOR DIMENSIONS EFFECTIVE FINISHING AREA Width Depth Height Width Depth Height Model Model TFC-461R 63-7/8″ 29-3/8″ 22″ TFC-461R 18″ 13″ 3-3/8″ (1622 mm) (746 mm) (559 mm) (457 mm) (330 mm) (86 mm) TFC-461R-L 63-7/8″ 29-3/8″ 22″ TFC-461R-L 18″...

  • Page 7: Installation

    Hatco. combustible flooring and surface finish and with no combustible material against the underside, or on non-combustible slabs or arches having 3.

  • Page 8: Programming The Unit

    PROGRAMMING THE UNIT Keys 9 and 10: When pressed, the unit will cycle continuously. The conveyor will advance in 1/2 GENERAL Thermo-Finisher conveyor units have both an second increments, pausing to heat the food at a upper and lower heating zone. The upper preset time/temperature, then convey the product elements heat the product on the pan/plate and out the opposite side of the unit.

  • Page 9: All Units

    PROGRAMMING THE UNIT ALL UNITS 1. Plug unit into an electrical outlet of the correct voltage, size and plug configuration (see SPECIFICATIONS for details). 2. Move POWER switch to ON position. The unit will make an audible beep, automatically go into preheat, and the display will indicate 3.

  • Page 10: Keys 9 And 10

    PROGRAMMING CONTROLLER KEYS 9 AND 10 (CYCLES CONTINUOUSLY WHEN PRESSED) 1. With display showing , simultaneously press/hold program selection key (9 or 10) and Enter key for five seconds. 2. After 3 seconds, the upper heat indicator glows and the unit displays (Upper Power Value).

  • Page 11: Auto-Off Mode

    PROGRAMMING CONTROLLER AUTO-OFF MODE The AUTO-OFF mode turns all the elements off if the unit has not been used for a programmed length of time. This feature can be adjusted from 1–60 minutes in one minute increments, or it can be set to never shut off by itself. 1.

  • Page 12: Operation

    OPERATION BASIC FOOD FINISHING WARNING Some exterior surfaces on the unit will get hot. Digital Use caution when touching these areas to avoid Display injury. Down Arrow CAUTION Enter Upper DO NOT use “Pyrex” glass plates or serving Heat pieces in the food finisher. “Pyrex” glass may Indicator break causing personal injury and/or food contamination.

  • Page 13: Food Finishing Hints

    OPERATION FOOD FINISHING HINTS 5. Adjust the backstop tray/landing platform (see Figure 9.). Pull up and position the pan • Position food product on center of conveyor belt horizontally for continuous operation. Adjust the between lines (see Figure 9). pan to the vertical position to prevent pans/plates •...

  • Page 14: Maintenance

    Upper and lower glass surfaces can be cleaned characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Genuine Hatco Replacement Parts when 1.

  • Page 15: Recommended Food Finishing Guide

    RECOMMENDED FOOD FINISHING GUIDE Food Item Top Power Top Time Bottom Power Bottom Time Apple Cobbler 9 minutes 9 minutes Frozen. 59 seconds 59 seconds PAN USED: Half sheet pan. May require extra time due to size of and thickness of pan. Chicken Wings 8 minutes 7 minutes...

  • Page 16: Troubleshooting

    Make sure wiring connections inside of unit do not work. is inoperable. are tight and secure. If secure, replace Electronic Control Board (Hatco part number 02.01.226.00). Make sure wiring connections inside of unit Unit operates correctly, but Electronic Control Board are tight and secure.
  • Page 17 TROUBLESHOOTING SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Excessive heat; elements Voltage too high. Check that voltage matches specification burn out rapidly. plate on front of unit. Check that installation location falls within specifications. Unit is operational, but Conveyor jammed. Remove any obstructions causing jam. conveyor rack does not turn.

  • Page 18: Hatco Limited Warranty

    PATENT OR OTHER INTELLECTUAL PROPERTY accordance with Hatco’s written instructions or 18 RIGHT INFRINGEMENT. Without limiting the months from the date of shipment from Hatco. Buyer generality of the foregoing, SUCH WARRANTIES must establish the product’s purchase date by DO NOT COVER: Coated incandescent light bulbs, returning Hatco’s Warranty Registration Card or by...
  • Page 19 NOTES Form No. TFC461RM-0108...

  • Page 20: Authorized Parts Distributors

    HATCO AUTHORIZED PARTS DISTRIBUTORS ALABAMA NEW YORK TEXAS IOWA Jones McLeod Appl. Svc. Acme American Repairs, Inc. GCS Service Electric Motor Service Co. Birmingham 205-251-0159 Brooklyn 718-456-6544 Fort Worth 817-831-0381 Davenport 319-323-1823 ARIZONA Alpro Service Co. Armstrong Repair Service Goodwin Tucker Group...

This manual is also suitable for:

Thermo-finisher tfc-461r-l

Table of Contents