Related Manuals for Snell IQSDA34
Summary of Contents for Snell IQSDA34
- Page 1 User Instruction Manual IQSDA34 Triple Channel 3G/HD/SD-SDI Reclocking Distribution Amplifier with RollCall snellgroup.com...
-
Page 2: Information And Notices
Information in this manual and software are subject to change without notice and does not represent a commitment on the part of Snell Limited. The software described in this manual is furnished under a license agreement and can not be reproduced or copied in any manner without prior agreement with Snell Limited or their authorized agents. -
Page 3: Table Of Contents
5.6.5 Input 1/2 Name..........23 6. Controlling the IQSDA34 from an Active Front Panel..... . 24 6.1 Information Window. -
Page 4: Introduction
1. Introduction 1.1 Module Description The IQSDA34 provides three inputs with 4 outputs per input for distribution of 1080p 3 Gbit/s SDI, HD-SDI 1.5 Gbit/s or 270 Mbit/s SD-SDI signals in a double width package. Its 70m 3G, 140m HD-SDI input equalization performance and non re-clocking distribution of wide-band signals makes it ideal for all current distribution applications. -
Page 5: Order Codes
Fig 2. IQSDA3400-2A3 & IQSDA3400-2B3 Rear Panel The input signal will bypass the module and be routed to the respective output in the event Note: of module removal or power failure. © Issue 2 Rev 3 Page 5 2015 Snell Limited... -
Page 6: Enclosures
1.4.1 B-style Enclosure Enclosure order codes: IQH3B-S-0, IQH3B-S-P 1.4.2 A-style Enclosures Enclosure order code: IQH1A-S-P Enclosure order codes: IQH3A-S-0, IQH3A-S-P Enclosure order codes: IQH3A-E-0, IQH3A-E-P, IQH3A-0-0, IQH3A-0-P Enclosure order code: IQH1A-S-P © Issue 2 Rev 3 Page 6 2015 Snell Limited... -
Page 7: Feature Summary
IQSDA34 www.snellgroup.com Introduction 1.5 Feature Summary The IQSDA34 provides the following features: • Triple channel Intelligent 3G-SDI, HD-SDI and SD-SDI re-clocking distribution amplifier • Will distribute DVB-ASI and other wide-band signals • Equalizes up to 70m at 3 Gbit/s, 140m at 1.5 Gbit/s and more than 350m at 270 Mbit/s when using Belden 1694A cable •... -
Page 8: Technical Specification
Input 1 (2, 3) Loss Input 1 (2, 3) 3G Input 1 (2, 3) HD Input 1 (2, 3) SD Other Controls User Memories Name, save and recall 16 user memories © Issue 2 Rev 3 Page 8 2015 Snell Limited... - Page 9 3 Gbit/s SDI, SMPTE 424M 1.5 Gbit/s HD-SDI, SMPTE 292M 270 Mbit/s SDI, SMPTE 259M-C / DVB-ASI Connector / Format BNC/ 75 Ohm panel jack on standard Snell connector panel Return Loss >-15 dB (270 Mbit/s, 1.5 Gbit/s) >-10 dB (3 Gbit/s) Output Jitter SD-SDI 0.2 UI (10 Hz) / 0.2 UI (1 kHz)
-
Page 10: Connections
IQSDA34 www.snellgroup.com Connections 3. Connections The IQSDA34 has 3 SDI inputs via 75ohm BNC connectors and 12 SDI outputs (3 groups of 4) via 75ohm BNC connectors. The input signals can be routed as: • A single input routed to all twelve outputs •... -
Page 11: Outputs
(Serial Out 1, output 2, Serial Out 2, output 2 and Serial Out 3, output 2 on Relay Bypass Version). 3.2.1 IQSDA3448-2A, IQSDA3448-2B, IQSDA3448-2A3 & IQSDA3448-2B3 Fig 5. IQSDA3448-2A, IQSDA3448-2B, IQSDA3448-2A3 & IQSDA3448-2B3 Outputs 3.2.2 IQSDA3400-2A3 & IQSDA3400-2B3 Fig 6. IQSDA3400-2A3 & IQSDA3400-2B3 Outputs © Issue 2 Rev 3 Page 11 2015 Snell Limited... -
Page 12: Card Edge Leds
• Both LEDs illuminated – 3 Gbit/s • Left LED only illuminated – 1.5 Gbit/s • Right LED only illuminated – 270 Mbit/s • Both LEDs off – Rate unknown © Issue 2 Rev 3 Page 12 2015 Snell Limited... -
Page 13: Controlling The Iqsda34 From The Rollcall Control Panel
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel 5. Controlling the IQSDA34 from the RollCall Control Panel 5.1 Unit Status Information about the status of the unit is displayed in the Unit Status section on each RollCall Control Panel screen. -
Page 14: Channels
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel 5.2 Channels The Channels screen enables the input type and signal routing to be specified. 5.2.1 SDI Rate • Auto: When selected, the unit will automatically detect and reclock any valid input signal, and the detected rate will be displayed in the Unit Status. -
Page 15: Input Source
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel If the On Input Loss / Mute option is selected, the output will be muted whenever a recognized rate is not detected; or, if the On Input Loss / Pass option is selected, any signal standard, frequency, etc... -
Page 16: Memory 1-16
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel 5.3 Memory 1-16 Use the Memory function to save up to 16 setups to be recalled later. Default memory names can be changed to provide more meaningful descriptions. To save settings: •... -
Page 17: Logging
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel 5.4 Logging Information about several parameters can be made available to a logging device that is connected to the RollCall network. Each logging screen comprises three columns: • Log Enable: Select the check boxes that correspond to the parameters for which log information should be collected. -
Page 18: Logging Channel 2 & 3
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel 5.4.2 Logging Channel 2 & 3 © Issue 2 Rev 3 Page 18 2015 Snell Limited... -
Page 19: Log Field Descriptions
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel 5.4.3 Log Field Descriptions Log Field Description Displays the module serial number. OS_VERSION= Displays the operating system name and version. BUILD_NUMBER= Displays the build number. HARDWARE_VERSION= Displays the hardware version number. -
Page 20: Rolltrack
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel 5.5 RollTrack The RollTrack screen allows information to be sent, via the RollCall™ network, to other compatible units connected on the same network. Use the settings on the RollTrack screen to: •... -
Page 21: Rolltrack Address
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel 5.5.4 RollTrack Address This item enables the address of the selected destination unit to be set. The address may be changed by typing the new destination in the text area and then selecting the S button to save the selection. -
Page 22: Setup
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel 5.6 Setup The Setup screen displays basic information about the unit. Use the functions on the screen to restart the unit, return all settings to their factory defaults, and to change the names of the inputs. -
Page 23: Input 1/2 Name
IQSDA34 www.snellgroup.com Controlling the IQSDA34 from the RollCall Control Panel 5.6.5 Input 1/2 Name These are the input names displayed in logging. To change the name of Input 1 or Input 2, type the name in the text field and click S. To return the name to its factory default, click P. -
Page 24: Controlling The Iqsda34 From An Active Front Panel
Controlling the IQSDA34 from an Active Front Panel 6. Controlling the IQSDA34 from an Active Front Panel The module can be operated from an active control panel via the RollCall™ network. All operational parameters and selections described in the previous section are made using a system of menus displayed in the two LCD windows –...
Need help?
Do you have a question about the IQSDA34 and is the answer not in the manual?
Questions and answers