Advertisement
Quick Links
Advertisement
Related Manuals for Gazer VI700A-SYNC3
Summary of Contents for Gazer VI700A-SYNC3
- Page 1 Gazer VI700A-SYNC3 Gazer VI700S-SYNC3 INSTALLATION MANUAL...
-
Page 2: Table Of Contents
Contents Precautions ..............................2 List of compatible cars ..........................3 Package contents ............................4 Special information ............................. 6 Car interior disassembly and connection guide for Ford Focus ............9 Troubleshooting ............................13... -
Page 3: Precautions
3. To install the product, use only original components that come in the package. 4. Do not attempt to repair the product by yourself. In case of malfunctions, please contact the authorized Gazer maintenance center. 5. Avoid hitting and damaging the product mechanically. -
Page 4: List Of Compatible Cars
List of compatible cars Gazer VI700A-SYNC3 and VI700S-SYNC3 is compatible with standard Ford Sync 3 systems with 8” touchscreen display. -
Page 5: Package Contents
Package contents Central unit with original monitor cables Power and CAN bus connection cables AUX cable Video-in cable Audio-in/out cable Remote mode switching button CAN bus signal processing unit 16 Gb Gazer micro SDHC memory card GPS antenna Microphone... - Page 6 Remote cable with a USB port Remote speaker Warranty card User manual...
-
Page 7: Special Information
Special information Video interface connection For the video interface to display an image, one needs to connect it directly to the built-in screen of the stock multimedia system. Video interface connection options: • Plug&Play connection to LVDS cable between the stock navigation system and the monitor; After the video interface is connected, the navigation system is controlled using the original touchscreen of the stock multimedia system. - Page 8 Once the calibration procedure is complete, press Android logo (for VI700A-SYNC3 model) or OK button (for VI700S-SYNC3 model). Caution! If the SD card slot is empty or DIP switch No. 6 is set to "On", the touch panel calibration...
-
Page 9: Figure
Audio connection There are several ways to arrange audio playback from the video interface: • Connection via Bluetooth in audio transmission mode. To do this, connect the stock multimedia system to the video interface via Bluetooth. Then select “Only audio” in the video interface Bluetooth settings. This is required for correct operation of Hands-Free function when a mobile phone is connected to the stock stereo system. -
Page 10: Car Interior Disassembly And Connection Guide For Ford Focus
Car interior disassembly and connection guide for Ford Focus Turn the ignition and all electrical devices off. Put the start key outside the car to avoid unintentional turning on of the ignition. Use the wedge tool (Fig. 1) to dismantle the plastic, carefully unlatch the panel along with the air vent deflectors as shown in figure 2. - Page 11 Release the multimedia system control unit by unscrewing 2 screws as shown in figure 3. Figure 3 Detach the multimedia system control unit from the shaft after switching off power and the CAN bus. Unscrew 4 fastening screws as shown in figure 4. Detach the multimedia system display after switching off power and the CAN bus.
- Page 12 Figure 5 Figure 6 Detach the protective rim “1” in the facing area "2". Remove the screw “3”. Unplug the facing “2” from the clamps in spots “4”. Disconnect and remove the facing "2" (Fig. 7). Figure 7...
- Page 13 Install the GPS antenna in the right bottom corner of the pillar on the windshield level as shown in figure 8. Figure 8 Install the microphone in the ceiling module as shown below (Fig. 9). Figure 9...
-
Page 14: Troubleshooting
Troubleshooting Malfunction Cause Possible solution No image/ black Not all plugs have been connected to the stock head Connect the remaining screen unit or monitor after installation. plugs. (manufacturer No power supplied to CAN unit (not all CAN-unit Check CAN unit power image). -
Page 15: Figure
Incorrect image size configure image setting. parameters for the corresponding video Incorrect image input. positioning. Camera feed Camera draws power directly from the reverse light. Use an extra relay for a displayed in black. stable signal. Camera feed is distorted. Unable to adjust Camera input video settings can be adjusted in AV2 Set video interface DIP...