Listening Through A Receiver (Home Theater); Check Points Before Requesting Service - Samsung BN68-01783B-00 User Manual

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the
TV speaker.
1 Press the TOOLS button.
Press the ENTER button to select Anynet+ (HDMI-CEC).
2 Press the ▲ or ▼ button to select Receiver.
Press the ◄ or ► button to select On or Off.
3 Press the EXIT button to exit.
If your receiver supports audio only, it may not appear in
the device list.
The receiver will work when you have properly connected
the Optical IN jack of the receiver to the Optical Out jack of the TV.
When the receiver (home theater) is set to On, you can hear sound output from the TV's Optical jack.
When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home
theater receiver. When the source is a digital component such as a DVD and is connected to the TV
via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
When listening through the receiver, there are restrictions for using the PIP and audio-related menus.
If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power
cord or a power failure), the Select Speaker may be set to External Speaker when you turn the TV
on again. (see page 34)

Check Points before Requesting Service

Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting
to Anynet + device...
appears on the screen.
The Anynet + device does
not play.
The connected device is
not displayed.
The TV programme cannot
be recorded.
The TV sound is not output
through the receiver.
Solution
■ Check if the device is an Anynet + device. The Anynet + system supports Anynet +
devices only.
■ Connect only one receiver.
■ Check if the Anynet + device power cord is properly connected.
■ Check the Anynet + device's Video/Audio/HDMI cable connections.
■ Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet + exclusive remote control.
■ Anynet + doesn't work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI cable, please make sure to search devices
again or restart your TV.
■ Check if the Anynet + Function of Anynet + device is set on.
■ Check if the Anynet + device is properly connected to the TV and check if the Anynet +
(HDMI-CEC) is set to On in the Anynet + Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then press the TOOLS
button to show the Anynet + menu and select a menu you want.
■ Select View TV in Anynet + menu.
■ Press the SOURCE button on the TV remote control and select a device other than
Anynet + devices.
■ Press any of CH, CH LIST, and PRE-CH to change to the TV mode.
(Note that the channel button operates only when a tuner-embedded Anynet + device
is not connected.)
■ You cannot use the remote control when you are configuring Anynet + or switching to a
view mode.
■ Use the remote control when the Anynet + setting or switching to view mode is complete.
■ You cannot use the play function when Plug & Play is in progress.
■ Check whether or not the device supports Anynet + functions.
■ Check whether or not the HDMI cable is properly connected.
■ Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
■ Search Anynet + devices again.
■ You can connect an Anynet + device using the HDMI cable only. Some HDMI cables
may not support Anynet + functions.
■ Check whether the antenna jack on the recording device is properly connected.
■ Connect the optical cable between TV and the receiver.
English - 69
View TV
Device List
Recording : DVDR
DVDR Operation
Receiver ◄
Setup
Move Adjust
On ►
Return