Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NETGEAR EN106TP
Summary of Contents for NETGEAR EN106TP
-
Page 2: Start Here
Start Here ™ Congratulations on your purchase of the NETGEAR Model EN104 , Model EN106 , or Model EN108 Ethernet hub. The hubs deliver standards-based, plug-and-play networking solutions for small businesses, home offices, and low- density workgroups of larger companies. -
Page 3: Package Contents
Model EN104 TP Model EN108 TP • Model EN106 hub, or • Mounting kit (for wall installation) • This installation guide • Warranty & Owner Registration Card • Power adapter • Support Information Card Model EN104TP/EN106TP/EN108TP Ethernet Hub Installation Guide... -
Page 4: Product Illustration
RJ-45 10BASE-T ports, the Model EN108 TP EN106 hub has six RJ-45 10BASE-T ports, and the has eight RJ-45 10BASE-T ports. Two LEDs—the Link LED and the Rx LED—are built into each 10BASE-T port. Link 8724EA Model EN104TP/EN106TP/EN108TP Ethernet Hub Installation Guide... -
Page 5: Normal/Uplink Push Button
10BASE-T ports are permanently configured for normal wiring for connection to a PC. Rear Panel The rear panel of the hub has a ground clip and a receptacle for the power adapter. Power receptacle 5Vdc 800mA — 8730FA Model EN104TP/EN106TP/EN108TP Ethernet Hub Installation Guide... -
Page 6: Installation Procedures
B connected, is close to an electrical outlet, and provides at least 2 inches of space all around the hub for ventilation. Model EN104TP/EN106TP/EN108TP Ethernet Hub Installation Guide... -
Page 7: Connect Devices To The Hub
Normal/Uplink push button to Normal. (The Model EN106 hub is shown in the illustration.) 8726FA Note: Ethernet specifications limit the cable length between your PC or server and the hub to 328 feet (100 meters) in length. Model EN104TP/EN106TP/EN108TP Ethernet Hub Installation Guide... -
Page 8: Connect The Hub To A Network
Connecting Device Cable Used Port 4, port 6, or port 8 PC, server, or router Straight-through cable set to Normal Port 4, port 6, or port 8 Hub or switch Straight-through cable set to Uplink Model EN104TP/EN106TP/EN108TP Ethernet Hub Installation Guide... -
Page 9: Cascade The Hub
Normal/Uplink push button on each hub. Model EN104 EN104 10 BASE-T HUB Normal Model EN106 EN106 10 BASE-T HUB Link/Rx Partition Normal/Uplink Uplink Model EN108 EN108 10 BASE-T HUB Uplink 8728FA Model EN104TP/EN106TP/EN108TP Ethernet Hub Installation Guide... -
Page 10: Verify The Installation
If the network is extremely busy, you may have to devices are segment the network with an Ethernet switch such as a connected on NETGEAR Ethernet switch or to upgrade your network to the network. Fast Ethernet operation. Wrong or Make sure the correct UTP cables are used. -
Page 11: Hub Integrity
Information Card. Replacement Power Adapter If, for any reason, the power adapter for any of the hubs fails, please contact NETGEAR immediately to order a replacement adapter. Use the following table when ordering a specific power adapter. Order code EN104TP, EN106TP PWR-024-001 Power adapter (7.5 V DC, 1 A), North America... -
Page 12: Technical Specifications
EN 55 022 (CISPR 22), Class A VCCI Class A C-Tick Safety Agency Approvals for Power Adapter CE mark, commercial UL listed (UL 1950), cUL TUV licensed (EN 60 950) T-Mark Warranty Limited lifetime warranty Power Adapter 3 Years Model EN104TP/EN106TP/EN108TP Ethernet Hub Installation Guide... - Page 13 In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
- Page 14 NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 Phone: 1-888-NETGEAR E-mail: support@NETGEAR.com http://www.NETGEAR.com *M-EN100TPNA-4*...