COBHAM SAILOR 6120 User Manual
  1. Manuals
  2. Brands
  3. COBHAM Manuals
  4. Antenna
  5. SAILOR 6120
  6. User manual

COBHAM SAILOR 6120 User Manual

Hide thumbs Also See for SAILOR 6120:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual
SAILOR 6120/30/40/50
User manual

Advertisement

Table of Contents
loading

Related Manuals for COBHAM SAILOR 6120

Summary of Contents for COBHAM SAILOR 6120

  • Page 1 SAILOR 6120/30/40/50 User manual...
  • Page 3 SAILOR 6120/30/40/50 User manual Document number: 98-154542-A Release date: September 21, 2017...
  • Page 4 In the event of any discrepancies, the English version shall be the governing text. Thrane & Thrane A/S is trading as Cobham SATCOM. Copyright © 2017 Thrane & Thrane A/S. All rights reserved.
  • Page 5 Warranties Any attempt to install or execute software not supplied by Cobham SATCOM on the devices in this system will result in the warranty being void. Any attempt to modify the software on these devices in a way not specified by Cobham SATCOM will result in the warranty being void.
  • Page 6 Safety summary The following general safety precautions must be observed during all phases of operation, service and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture and intended use of the equipment.
  • Page 7 SAILOR 3027 Non-SOLAS Terminal Intended readers This manual is a user manual for the SAILOR 6120/30/40/50 systems. The manual is intended for anyone who is using or intends to use any of these four systems. No specific skills are required to operate the mini-C system. However,...
  • Page 8 • Service contains information on software update and a short troubleshooting guide and explains how to check the status of the system. Related documents Ref Title and description Document no. SAILOR 6120/30/40/50, Installation manual 98-154541 (with SAILOR 6018 Message Terminal) SAILOR 6110 mini-C GMDSS, User manual 98-154172...
  • Page 9 Typography In this manual, typography is used as indicated below: Bold is used for the following purposes: • To emphasize words. Example: “Do not touch the antenna”. • To indicate what the user should select in the user interface. Example: “Select SETTINGS > LAN”. Italic is used to emphasize the paragraph title in cross-references.
  • Page 10 viii...

  • Page 11: Table Of Contents

    Contents Chapter 1 Introduction Welcome ....................1 System overview ................... 2 System units .................... 4 User interfaces ..................5 The Inmarsat C services ..............9 Chapter 2 Get started Registration ..................13 User interfaces ..................14 Start up the system ................18 Chapter 3 To use easyMail Overview of easyMail ..............
  • Page 12 Set up easyMail .................. 63 Chapter 4 To use Distress and SSA buttons To send a Distress Alert (SAILOR 6150 only) ....... 65 To send a Ship Security Alert (SAILOR 6120 only) ... 69 Chapter 5 Service Get support ................... 71 Troubleshooting guide ..............

  • Page 13: Chapter 1 Introduction

    With the mini-C system you can send and receive data via satellite through the Inmarsat C network. Four variants of the mini-C system are described in this manual: • SAILOR 6120 SSA System • SAILOR 6130 LRIT System • SAILOR 6140 Maritime System •...

  • Page 14: System Overview

    Chapter 1: Introduction System overview The SAILOR 6120/30/40/50 mini-C system The Inmarsat C satellite network is the link between the mini-C system and the destination office. It uses four geostationary satellites to cover the world. For each satellite there is an NCS, Network Coordination Station, handling registration of the mobile unit (in this case the SAILOR 3027) in the Inmarsat C system.
  • Page 15 Chapter 1: Introduction The SAILOR 3027 can be connected to a SAILOR 6018 Message Terminal, where you can read and write messages and send Distress alerts (SAILOR 6150 only). This communication is transmitted via the SAILOR 3027 to/from the Inmarsat C satellite network. Scripting The SAILOR 6194 Terminal Control Unit supports simple scripting, using Lua language.

  • Page 16: System Units

    SAILOR 6150 systems only, but is available for the other systems as well. For a more detailed description of the units, refer to the installation manual for the SAILOR 6120/30/40/50 mini-C system and the manuals for the respective units. See Related documents on page vi. System units...

  • Page 17: User Interfaces

    CAN interface. The SAILOR 6018 has a built-in user interface. For overall system status, diagnostics and live logging you may use the ThraneLINK Management System (TMA). For details on the TMA, see the SAILOR 6120/30/40/50, Installation manual [1]. User interfaces...
  • Page 18 Chapter 1: Introduction easyMail easyMail is a user interface for the mini-C system. With easyMail you can send and receive messages, view status and configure the system. To use easyMail you must have a SAILOR 6194 Terminal Control Unit and a computer with the easyMail application installed.
  • Page 19 Chapter 1: Introduction SAILOR 6018 user interface (for SAILOR 6150) For the SAILOR 6150 Non-SOLAS system you can use the SAILOR 6018 Message Terminal. With the SAILOR 6018 Message Terminal you can send and receive messages, send Distress alerts, view system status and configure the system.
  • Page 20 Chapter 1: Introduction Menu overview, SAILOR 6018 The below drawing shows the menu system in the SAILOR 6018. Note: Menu items in grey colour are only available if Cyrillic characters are enabled under System > Settings > Regional settings > Cyrillic. The items in the menu overview are described in SAILOR 6110 mini-C GMDSS, User manual [2].

  • Page 21: The Inmarsat C Services

    Distress alerts and Distress priority messages If a ship or a crew is in grave and imminent danger, the crew can use the SAILOR 6120/30/40/50 to send a Distress alert by pushing a dedicated Distress button. The alert contains information on the terminal’s ID (ID of the SAILOR 3027), addressed LES, date/time of alert, ship’s position, course, speed, time...
  • Page 22 Chapter 1: Introduction Enhanced Group Call (EGC) Two EGC services are available: • EGC SafetyNET - the international safety service, which allows authorised maritime safety information (MSI) providers, such as meteorological offices, hydrographic officers and MRCCs to broadcast messages to all ships in certain geographical areas. MSI includes navigational and meteorological warnings, meteorological forecasts and other urgent safety-related information, which is addressed to all ships in NAVAREA / METAREA, user-defined circular or...
  • Page 23 Chapter 1: Introduction Message transmission Ship to shore: Text and data from the SAILOR 3027 can be sent to: • An e-mail address • Any telex or fax (text, one way only) number • Any computer connected to the public telephone and data networks (PSTN and PSDN), using a telephone modem number •...
  • Page 24 Chapter 1: Introduction 3027 sends its reports to this mailbox and other tracking systems can then access and empty the mailbox. The SAILOR 3027 supports up to 64 DNIDs. Up to 255 mobile terminals can use the same DNID, and the specific terminal is identified by a member number between 1 and 255.

  • Page 25: Chapter 2 Get Started

    Chapter 2 Get started This chapter explains how to register, start up and log on your mini-C system. It has the following sections: • Registration • User interfaces • Start up the system Registration Before using the SAILOR 3027 mini-C terminal on the Inmarsat-C system you must register the terminal.

  • Page 26: User Interfaces

    Install easyMail To install the easyMail application on your computer, do as follows: 1. Go to www.cobham.com/satcom 2. Select Cobham SYNC Partner Portal. 3. Select Downloads > Product software > Maritime. 4. Search for the easyMail software. 5. Click Download.
  • Page 27 Chapter 2: Get started Access your SAILOR 3027 with easyMail 1. Acquire a SAILOR 6194 Terminal Control Unit, if it is not already part of your system. 2. Connect your SAILOR 3027 to the CAN interface on the SAILOR 6194 Terminal Control Unit.
  • Page 28 Chapter 2: Get started SAILOR 6018 Message Terminal The SAILOR 6018 has its own built-in user interface. If you are using a SAILOR 6018 with your SAILOR 6150 Non-SOLAS system, you must config- ure the SAILOR 6018 before using it for the first time. The initial configuration may already have been done during Note installation of the system.
  • Page 29 Chapter 2: Get started For details on how to use the SAILOR 6018, see SAILOR 6110 mini-C GMDSS, User manual [2]. If, at a later stage, you want to switch between the Radiotelex and Inmarsat C applications, do as follows: 1.

  • Page 30: Start Up The System

    Chapter 2: Get started Start up the system easyMail When the power source is on, the SAILOR 3027 automatically starts up and logs on to the satellite network. You can see the logon status on screen on a connected computer with easyMail installed.
  • Page 31 Chapter 2: Get started Log into the satellite network The SAILOR 3027 logs into the Inmarsat C network automatically at startup. The upper right corner of the display shows if the system is logged If, however, the selected satellite is no longer available, you must manually select another satellite to log into.
  • Page 32 Chapter 2: Get started 2. On the Network Status page select Login. 3. Select the Ocean Region to which you want to log in. If the selected satellite is available, the system will now log in. When the display shows the Ocean Region and the position, and there is a green check mark at the satellite symbol, the system is ready for use.

  • Page 33: Chapter 3 To Use Easymail

    Chapter 3 To use easyMail This chapter describes how to operate the mini-C system using the easyMail application. It has the following sections: • Overview of easyMail • Distress functions (only SAILOR 6150) • Work with messages • Position reporting •...

  • Page 34: Overview Of Easymail

    Chapter 3: To use easyMail Overview of easyMail For information on how to install and start up easyMail, see easyMail application on page 14. Overview of the screen Below is an overview of the main screen in easyMail. Menu bar Mobile status Connection status Message...
  • Page 35 Chapter 3: To use easyMail • Connection status shows the status of your PC connection, your mini-C antenna connection and your GPS connection. • Message header contains the fields where you can enter recipients and subject for a message. • Shortcut buttons may be used for quick access to some of the menu items.
  • Page 36 Chapter 3: To use easyMail Menu overview, easyMail Overview of easyMail...

  • Page 37: Distress Functions (Only Sailor 6150)

    Chapter 3: To use easyMail Distress functions (only SAILOR 6150) Write a Distress priority message Distress priority messages are sent to the MRCC only. Note Distress priority messages must be written in English. To write a Distress priority message, do as follows: 1.
  • Page 38 Chapter 3: To use easyMail The Distress Alert Nature and the Distress Alert Position, Course Note and Speed settings are only valid for the current Distress Alert or maximum one hour. Then these settings are returned to the default settings. The entered Distress LESes remain in the system. To change the Distress alert settings, do as follows: 1.
  • Page 39 Chapter 3: To use easyMail 4. If necessary, change the position, course and speed. Do not change the default setting unless you have good Note reasons to do so. The default setting is “Always use latest position from GPS”. It is normally best to show your current GPS position when sending a Distress Alert.
  • Page 40 Chapter 3: To use easyMail Test Distress buttons Never test the installation by sending an alert on-air! Important If an alert is sent by mistake, inform the relevant authorities immediately. You can test the Distress button(s) in your system without sending a real Distress alert.
  • Page 41 Chapter 3: To use easyMail Test easyMail alarm sound To test the alarm sound in easyMail, do as follows: 1. Select Distress > Test easyMail sound. 2. Click Start to hear the sound on your computer. Your computer will now play the same sound that you will hear when a Distress alert is sent or an urgent/distress priority EGC or message is received.

  • Page 42: Work With Messages

    Chapter 3: To use easyMail Work with messages Prepare the system Before you can send a message: • The recipient of the message must be listed in the Address book. For details, see Manage the list of Contacts on page 38. •...
  • Page 43 Chapter 3: To use easyMail Write a routine priority message To write a routine priority message, do as follows: 1. If the editor is not already open, select File > New or click the Editor button to the left (if present). 2.
  • Page 44 Chapter 3: To use easyMail If you want to save your message without sending it, you can Note save it as a file by selecting File > Save. 6. When the message is ready to be sent, click Send. 7. Select what you want to send. •...
  • Page 45 Chapter 3: To use easyMail Options for writing and sending messages In the File menu, you have the following options: • New. Opens a new message. • Open. Allows you to select a text file to be opened in the editor. •...
  • Page 46 Chapter 3: To use easyMail To insert information automatically To insert information such as position and vessel data in your message, do as follows: 1. Select Edit > Insert. 2. Select the information you want to insert. Signature and vessel data must first be defined. See the next Note section.
  • Page 47 Chapter 3: To use easyMail To enter signature and vessel data You can enter a signature and your vessel data for later automatic insertion in your messages (see previous section). To define your signature, do as follows: 1. Select Edit > Define signature. 2.
  • Page 48 Chapter 3: To use easyMail To use default messages You can write a default message that you can recall and send by pressing one of the F-keys F1 to F8. Create a default message To create a default message, do as follows: 1.
  • Page 49 Chapter 3: To use easyMail View messages in the Inbox To view the messages in the Inbox, do as follows: 1. Select View > Inbox. 2. Double-click the message you want to read. From within the message you have the following options: •...
  • Page 50 Chapter 3: To use easyMail View sent messages (Outbox) After writing a message and selecting Send, you can see the message and the status of the message in the Outbox. To view messages in the Outbox, select View > Outbox. Manage the list of Contacts or select Messaging >...
  • Page 51 Chapter 3: To use easyMail To add a new contact Do as follows: 1. In the Address book, select New at the bottom of the page. 2. Type in the name of your contact. 3. Select the address type below the name. 4.
  • Page 52 Type Format of number Example Presentation E-mail Standard e-mail address info@cobham.com 5, 7 or 8 bit Telex Country code + subscriber no. 0045 99999999 5 or 7 bit Country code + subscriber no. 0045 99999999 5, 7 or 8 bit...
  • Page 53 Chapter 3: To use easyMail To edit a contact Do as follows: 1. In the Address book, select the contact. 2. Select Properties. 3. Edit the details. See the previous section for information on the contact details. 4. Select OK. To delete a contact Do as follows: 1.

  • Page 54: Position Reporting

    Chapter 3: To use easyMail Position reporting For general information on the position reporting service, see Position reports on page 11. To be able to use the position reporting feature, a DNID must be Note downloaded and enabled in the SAILOR 3027. See Set up ENIDs on page 53.
  • Page 55 Chapter 3: To use easyMail To start a local position reporting program Note Only local position reporting programs can be managed locally. You can see the remotely configured programs as well but you cannot change them. To start a program that is already defined, do as follows: 1.

  • Page 56: Receive Egcs

    Chapter 3: To use easyMail 2. Select the DNID information (provider, LES, DNID and member number) for each ocean region. 3. Select the time to start the position reporting or select Immediately. 4. Select the interval between the position reports. 5.
  • Page 57 Chapter 3: To use easyMail View incoming EGCs To view EGCs, do as follows: 1. Select View > EGC from the main menu. 2. Double-click an EGC to see the contents. From within the EGC you have the following options: •...

  • Page 58: Network Status And Settings

    Chapter 3: To use easyMail Network status and settings The Mobile status field at the top of the page shows the status of the network connection. When the SAILOR 3027 is logged in to the network, this field shows the ocean region to which the SAILOR 3027 is logged in. Log into and out of the network To log into the Inmarsat C network, select Actions >...
  • Page 59 Chapter 3: To use easyMail Link test Note To test basic system connectivity, we recommend that you send a short message to yourself instead of using the link test. For details on how to send a message, see Write a routine priority message on page 31.

  • Page 60: View System Details

    Chapter 3: To use easyMail View system details To see information on easyMail and the SAILOR 3027, click or select Help > System info. View system details...

  • Page 61: View Or Change Position Information

    Chapter 3: To use easyMail View or change position information To view or change your current position information, course and speed, do as follows: 1. select View > Position info. 2. If there is no synchronization with the positioning system, you can enter a manual position, course and speed.

  • Page 62: View Status And Info Log

    Chapter 3: To use easyMail View status and Info log To see status To see the status of the SAILOR 3027, select View > Transceiver status, or click the Antenna signal bar in the connections status field at the top of the page.

  • Page 63: Set Up The Default Isp And Default Leses

    Chapter 3: To use easyMail Set up the default ISP and default LESes To set up the default ISP To set up a default ISP, do as follows: 1. Select Setup > Default ISP. 2. Select the default ISP from the list. 3.

  • Page 64: Set Up Reception Of Egcs

    Chapter 3: To use easyMail Set up reception of EGCs For general information on EGCs, see Enhanced Group Call (EGC) on page 10. To set up reception of EGCs, do as follows: 1. Select Setup > EGCs. 2. To set up the additional areas from which you want to receive meteorological or navigational EGCs, select Additional NAVAREA(s) /METAREA(s).

  • Page 65: Set Up Enids

    Chapter 3: To use easyMail 3. Select whether you want to receive System Messages or SafetyNET messages or both. 4. To change the Coastal Warning Areas, type in the new areas under Coastal Warning Areas [A..Z]. 5. Select the types of EGC service you want to receive. 6.

  • Page 66: Set Up The Land Earth Stations (Les)

    Chapter 3: To use easyMail Set up the Land Earth Stations (LES) To view or edit the list of Land Earth Stations for each ocean region, do as follows: 1. Select Setup > Land Earth Stations (LES). 2. Select a LES and click Edit. 3.
  • Page 67 Chapter 3: To use easyMail List of currently supported LESes The table below shows the LESes supported by the service providers at the time of writing. Note that the list is dynamic, so it may not be completely up to date. LES no.

  • Page 68: Set Up Inmarsat Service Providers (Isp)

    Chapter 3: To use easyMail Set up Inmarsat Service Providers (ISP) Do not change these settings unless you know the exact formats Note to enter. The Inmarsat Service Providers are already set up when you receive your system. However, if an Inmarsat Service Provider e.g. changes the format for email, you can change these settings to match the new format.
  • Page 69 Chapter 3: To use easyMail To add a new provider To add a new provider to the list, do as follows: 1. In the Inmarsat service providers window, click New provider. 2. Type the name of the provider in the top left corner and click Add. The new provider is now added to the list, but without any information.

  • Page 70: Enter The Mobile Number

    Chapter 3: To use easyMail Enter the mobile number Before you can use the SAILOR 3027 on the Inmarsat C network you must configure the mobile number from your service provider in the SAILOR 3027. To enter the mobile number, do as follows: 1.

  • Page 71: Set The Local Time

    Chapter 3: To use easyMail Set the local time The SAILOR 3027 gets the UTC time from the GPS receiver. You can convert this time to local time and set the time on your computer accordingly. Do as follows: 1. Select Setup > Local time zone/PC time. 2.

  • Page 72: Set Up Password Protection

    Chapter 3: To use easyMail Set up password protection You can add password protection to three different actions: Transmission, configuration and remote configuration. To add password protection, do as follows: 1. Select Setup > Passwords. 2. Select the password you want to add or change. 3.

  • Page 73: Set Up Pc Communication With The Sailor 3027

    Chapter 3: To use easyMail Set up PC communication with the SAILOR 3027 To connect a computer to the system you must use a SAILOR 6194 Terminal Control Unit. You can connect the computer to the LAN interface or the RS-232 interface on the SAILOR 6194. Note The Communication setup is not accessible when the computer has established a connection with the SAILOR 3027.
  • Page 74 Chapter 3: To use easyMail To set up RS-232 communication To set up easyMail for RS-232 communication with the SAILOR 6194 and thereby the SAILOR 3027, do as follows: 1. Select Setup > Communication setup. 2. Select Serial communication. 3. Select the COM port you are using on your computer and the Baud rate of the SAILOR 6194 (default is 115200).

  • Page 75: Set Up Easymail

    Chapter 3: To use easyMail Set up easyMail To change message setup You can set up some general settings for messages in the Messages tab. Do as follows: 1. Select Setup > Settings. 2. Select the Messages tab. 3. If you want to get an info box when a new message has arrived, select Show info box when new message is received.
  • Page 76 Chapter 3: To use easyMail To use electronic forms Some users have a need for a specific layout, e.g. for fishery catch reporting. The files for this layout must be downloaded to the system before selecting the formats on this page. Miscellaneous settings In Harbour Button Select Setup >...

  • Page 77: Chapter 4 To Use Distress And Ssa Buttons

    Ship Security Alert with the SSA buttons. It has the following sections: • To send a Distress Alert (SAILOR 6150 only) • To send a Ship Security Alert (SAILOR 6120 only) To send a Distress Alert (SAILOR 6150 only) Distress alert with SAILOR 3042E...
  • Page 78 Chapter 4: To use Distress and SSA buttons The MRCC normally sends a message to the alerting unit to Important gather more information about the situation. If possible, respond to such messages with a Distress message sent to the same LES that was used for the Distress Alert.
  • Page 79 Chapter 4: To use Distress and SSA buttons Distress alert with SAILOR 6018 If you have a SAILOR 6018 Message Terminal connected to your SAILOR 6150 system, you can use the Distress button on the SAILOR 6018 to send Distress alerts, and you may also have additional SAILOR 6101 or SAILOR 6103 alarm panels connected.
  • Page 80 Chapter 4: To use Distress and SSA buttons The below table shows the behavior of the Distress button on the SAILOR 6018. Behavior Meaning Button light flashes, The Distress button is pushed. Hold until light buzzer sounds and sound changes (more than 3 seconds). Button light constant, The Distress Alert is being sent buzzer is silent...

  • Page 81: To Send A Ship Security Alert (Sailor 6120 Only)

    Install the SSA buttons and configure the SAILOR 3027 as described in SAILOR 6194 Terminal Control Unit, Installation and user manual [4] and SAILOR 6120/30/40/50, Installation manual [1]. To send a Ship Security Alert (SAILOR 6120 only)
  • Page 82 30 – 33 seconds during test, an SSA Test Message is sent to all recipients configured to receive test messages. 1. “Operational” means the following criteria are met: GPS fix obtained, logged in, recipient(s) of covert alert configured, all SSA buttons connected correctly. To send a Ship Security Alert (SAILOR 6120 only)

  • Page 83: Chapter 5 Service

    Airtime subscription documents for a contact number to call. System support Lists of certified partners and distributors are available on www.cobham.com/satcom. Select Technical Service Partner List from the menu to the right and select one of the dealers or partners lists shown.

  • Page 84: Troubleshooting Guide

    Chapter 5: Service Troubleshooting guide The below table provides information on some of the problems that might occur, including possible causes and remedies to solve the problems. Problem Possible cause Remedy The system The SAILOR 6018 has a If the SAILOR 6018 is using a cannot be remote on/off switch, so the remote on/off switch, use...
  • Page 85 Chapter 5: Service Problem Possible cause Remedy No connection The PC connection to the For information on how to between SAILOR 3027 is not set up set up the PC connection, see easyMail and properly. Set up PC communication SAILOR 3027 with the SAILOR 3027 on page 61.

  • Page 86: Status Signalling In Easymail

    Chapter 5: Service Status signalling in easyMail Status information The top of the display shows the most important status information. You can click each status area to get details, or use the View menu to enter the status pages. Information of events Popup windows When an event requires your attention, a popup window appears.

  • Page 87: Status Signalling In Sailor 6018

    Chapter 5: Service Status signalling in SAILOR 6018 The SAILOR 6018 can show basic status and error messages. When an error occurs in the system, check the SAILOR 6018 for information first. Status information in SAILOR 6018 The upper right corner of the display shows the most important status information.
  • Page 88 Chapter 5: Service List of active warnings and errors The top right corner of the display shows a short text about the current status. The icon in the corner can change depending on the situation. From the list of active warnings and errors you can access the event log. Event log From the list of active errors or warnings, you can select Event log to see a complete list of events.

  • Page 89: Service And Repair

    Your dealer, installer or Cobham SATCOM partner will assist you whether the need is user training, technical support, arranging on-site repair or sending the product for repair. Your dealer, installer or Cobham SATCOM partner will also take care of any warranty issue.
  • Page 90 Chapter 5: Service Service and repair...
  • Page 91 Appendix A Conformity CE (RED) The mini-C systems SAILOR 6120, SAILOR 6130, SAILOR 6140 and SAILOR 6150 are CE certified as stated in the “EU Declaration of Conformity” enclosed in electronic copy on the next pages.
  • Page 92 The full text of the EU declaration of conformity is available at the following internet address: http://sync.cobham.com/satcom/support/downloads Document no.: 99-157523-A Thrane & Thrane A/S trading as Cobham SATCOM. Registered no.: DK - 65 72 46 18. Registered address: Lundtoftegaardsvej 93 D, 2800 Kgs. Lyngby, Denmark. www.cobham.com...
  • Page 93 The full text of the EU declaration of conformity is available at the following internet address: http://sync.cobham.com/satcom/support/downloads Document no.: 99-157524-A Thrane & Thrane A/S trading as Cobham SATCOM. Registered no.: DK - 65 72 46 18. Registered address: Lundtoftegaardsvej 93 D, 2800 Kgs. Lyngby, Denmark. www.cobham.com...
  • Page 94 The full text of the EU declaration of conformity is available at the following internet address: http://sync.cobham.com/satcom/support/downloads Document no.: 99-157525-A Thrane & Thrane A/S trading as Cobham SATCOM. Registered no.: DK - 65 72 46 18. Registered address: Lundtoftegaardsvej 93 D, 2800 Kgs. Lyngby, Denmark. www.cobham.com...
  • Page 95 The full text of the EU declaration of conformity is available at the following internet address: http://sync.cobham.com/satcom/support/downloads Document no.: 99-157526-A Thrane & Thrane A/S trading as Cobham SATCOM. Registered no.: DK - 65 72 46 18. Registered address: Lundtoftegaardsvej 93 D, 2800 Kgs. Lyngby, Denmark. www.cobham.com...
  • Page 96 Appendix A: Conformity...
  • Page 97 Appendix B GNU License texts GNU General Public License Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
  • Page 98 Appendix B: GNU License texts Whether that is true depends on what the Program does. 1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty;...
  • Page 99 Appendix B: GNU License texts terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works.
  • Page 100 Appendix B: GNU License texts DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
  • Page 101 Appendix B: GNU License texts GNU Lesser General Public License Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
  • Page 102 Appendix B: GNU License texts case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software.
  • Page 103 Appendix B: GNU License texts License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
  • Page 104 Appendix B: GNU License texts contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made...
  • Page 105 Appendix B: GNU License texts contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
  • Page 106 Appendix B: GNU License texts You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker.

  • Page 107: Glossary

    Glossary Glossary Controller-Area Network. A message based protocol designed to allow microcontrollers and devices to communicate with each other within a vehicle without a host computer. DNIC Data Network Identification Code DNID Data reporting Network IDentification code. An address code to an electronic mailbox at the Land Earth Station.
  • Page 108 Glossary GNU’s Not Unix. A Unix-like computer operating system developed by the GNU project, ultimately aiming to be a "complete Unix-compatible software system" composed wholly of free software General Public License Global Positioning System. A system of satellites, computers, and receivers that is able to determine the latitude and longitude of a receiver on Earth by calculating the time difference for signals from different satellites to reach the receiver.
  • Page 109 Glossary LRIT Long Range Identification and Tracking. A system established by the IMO applying to all passenger ships, cargo ships > 300 gross tonnage and mobile offshore drilling units. These ships/units must automatically report their position to their Flag Administration at least 4 times a day. Other contracting governments may request information about vessels in which they have a legitimate interest under the regulation.
  • Page 110 Glossary PSTN Public Switched Telephone Network. The network of the world’s public circuit-switched telephone networks. It consists of telephone lines, fibre-optic cables, microwave transmission links, cellular networks, communications satellites, and undersea telephone cables all inter-connected by switching centres which allows any telephone in the world to communicate with any other.

  • Page 111: Index

    Index Index deleting EGC, 45 activation of service, 13 message, 37 alert Distress Ship Security Alert, 69 alert with SAILOR 3042E, 65 approvals, 79 alert with SAILOR 6018, 67 auto-print button test (easyMail), 28 EGCs and messages, 63 clear indications (easyMail), 66 clear indications (SAILOR 6018), 69 description of service, 9 message, 25...
  • Page 112 Index mobile number entering, 58 Inbox, 37 info log, 74 network login, 46 scan, 46 setup with easyMail, 61 view status, 46 LES number Distress (SAILOR 6018), 67 list of supported, 55 link test, 47 Outbox, 38 login, 46 script language, 3 position for Distress, 27 viewing, 49...
  • Page 113 Index system units, 4 safety summary, iv SAILOR 3042E sending Distress alert, 65 transmission stop, 47 SAILOR 6018 troubleshooting, 71 menu overview, 8 typography used in this manual, vii sending Distress alert, 67 scan, 46 script introduction, 3 units in the system, 4 Lua, 3 user interface, 5 sent items, 38...
  • Page 114 98-154542-A www.cobham.com/satcom...

This manual is also suitable for:

Sailor 6140Sailor 6130Sailor 6150

Table of Contents