NiteRider Lumina Micro 220 User Manual

DISCOVER THE NIGHT
Thank you for choosing the Lumina
Micro 220 from NiteRider, the
innovator in technical lighting systems.
The Lumina Micro 220 combines a
self contained, high-powered, white
LED headlamp with a rechargeable,
replaceable Lithium Ion battery. To get
the most from your NiteRider light, we
urge you to familiarize yourself with
the following safety and operating
instructions.
PARTS LIST AND IDENTIFICATION
Please verify the contents of your
Lumina system:
A. Lumina Micro 220 Headlamp
B. Lumina Handlebar Mount
C. Lumina Handlebar Mount Shim
D. USB Charging Cable
A.
Lumina Micro 220
User Guide
C.
OPERATION
MOUNTING
The Lumina Handlebar Mount is designed to 1. The light has 5 modes - low, medium and
high beam - daylight flash mode and walk
fit on virtually any handlebar.
mode. Press and release the headlamp
power button to turn the light on. Cycle
Remove the headlamp from the mount by
through the three brightness levels by
pressing down on the release
pressing and releasing the power button.
lever and sliding the headlamp
off of the mount towards the 2. To access the daylight visible flash mode,
press and hold the power button for greater
release lever.
than 3 seconds or until the headlamp begins
to flash.
Hinge
Release Lever
3. With the headlamp in flash mode, press
Turn the knob counter-
and release the power button to access walk
clockwise, allowing the hinge
mode. From walk mode you can return to
to swing open. Place the
normal mode by pressing and releasing the
mount on the handlebar
Knob
power button.
on the either side of the
stem.
Swing the hinge down 4. To turn the light off from either normal,
to make contact with the
flash, or walk mode, press and hold the
handlebar. Swing the hex
power button until the light turns off.
bolt up, seating the knob
into its recess. Turn the
5. Like the other Lumina Series models, the
knob clockwise to tighten
B.
and secure the mount to Lumina Micro 220 comes equipped with a "lock"
the handlebar.
mode. Always put the light into lock mode during
transport of the headlamp in order to prevent
accidentally turning the headlamp on. To put the
headlamp in lock mode, press and hold the power
Aim the
button for several seconds until the headlamp
headlamp by
turns off and continue holding the power button
swiveling the
down through flash mode until the power button
headlamp
turns or flashes red. Then let go of the Power
back
and forth. button and test to make sure the light is in lock
mode by tapping the power button. The light will
D.
not turn on if the lock mode is engaged.
6. To unlock the headlamp, press and hold the RIDING AT NIGHT
power button for several seconds until the power
While a Lumina Micro 220 lighting system
button turns, or flashes blue. Release the power
will improve your view, control and
button. enjoyment of night riding, please remember
that cycling at night is an inherently
dangerous activity. In addition to using your
lighting system properly and riding with
LOW BATTERY INDICATOR
extreme caution, NiteRider urges you to:
With approximately 15 - 20% battery
capacity remaining, the indicator LED on the
• Never ride alone.
headlamp will turn from blue to red. • Always let someone know where you
are going.
RESERVE MODE • Wear a helmet and reflective clothing.
Reserve Mode will automatically shift your
• Carry an auxiliary light and emergency
light to low beam when the battery is very
supplies.
low and about to cut off. Once reserve
• Make sure the headlamp & mounting
mode starts you will only be able to use Low
bracket is securely fastened.
Beam, Flash Mode and Walking Mode. High
Beam and Medium Beam will be disabled.
IMPORTANT INFORMATION!
BATTERY CHARGING AND CARE
1. Plug the micro USB side of the USB
LOCK THE HEADLAMP FOR TRANSIT
charging cable into the Lumina Micro
It is important to lock the headlamp and
220 charging port and the other into your
protect the switch from being pressed
computer.
while it is in transit. The headlamp can be
2. The LED charging indicator on the Lumina
easily turned on if placed in something like
Micro 220 will remain red until the battery
a backpack, duffel bag or suitcase. The
is fully charged; once charged it will then
headlamp gets hot while in operation. To
switch to blue.
prevent potential damage from high heat
3. Leaving the headlamp and USB charging or even fire, it is very important to put the
cable connected indefinitely will not harm headlamp in lock mode and protect the
the battery. switch from being pressed.
NiteRider will not be held responsible for
4. When storing for an extended period of
damages to person or property resulting
time, charge the battery every 4-6 weeks to
from a failure to follow the 'lock' mode
maximize battery life.
instructions.
PROTECTING YOUR INVESTMENT
Properly charge your battery to maximize RUN TIMES
its lifespan. (See the "Battery Charging and
The Lumina Micro 220 will run up to:
Care" section for detailed information)
The Lumina Micro 220 will perform in wet Light Level Time*
High 1:30
weather conditions, but submerging it in
Med 2:45
water will damage the system.
Low 4:00
Walk 14:00
SUPPORT
If you experience difficulties during product
installation or operation, NiteRider provides
free telephone support on weekdays from *Run times are approximations and will vary.
8:00 AM to 4:30 PM (Pacific Time) at
800.466.8366, ext 4. You may also e-mail us
at support@niterider.com.
WARRANTY
NiteRider stands behind its products with the
following warranties:
•Lifetime warranty on all mechanical
components
•2 years on electrical components
•1 year on rechargeable batteries
To obtain warranty service, it is preferable
to have your original sales receipt. Contact
the NiteRider customer service department
at 800.466.8366, ext 4 to obtain a Return
Merchandise Authorization (RMA) number.
The RMA number must be prominently
displayed on the outside of your package.
The product must be properly packaged to
prevent damage in transit. For complete
warranty information, please visit our website
at www.niterider.com.
Lumens
220
120
80
15
150-23220