Sony FCB-ER8550 Technical Manual page 39

Command List (6/7)
Command Set Command
CAM_FocusPosReply —
IntervalTimeSet
CAM_RegisterValue —
CAM_ColorEnhance Parameter Set
On
Off
CAM_ChromaSuppress —
CAM_ColorGain Direct
CAM_ColorHue Direct
CAM_ExExpComp Reset
(Extended command)
Up
Down
Direct
CAM_ExAperture Reset
(Extended command)
Up
Down
Direct
CAM_ExAutoICR Threshold
(Extended command) (ON→OFF)
On Level
CAM_ExColorGain Direct
(Extended command)
CAM_ExColorHue Direct
(Extended command)
CAM_HLC Parameter Set
CAM_ColorBar Off
On (Color bar 100%
8 colors)
On (Color bar 100%
7 colors)
On (Gray scale)
Command Packet
8x 01 04 1A 00 00 0p 0p FF
8x 01 04 24 mn 0p 0q FF
8x 01 04 20 mm 00 pp 40 40 ss 40 40 FF
8x 01 04 50 02 FF
8x 01 04 50 03 FF
8x 01 04 5F 0p FF
8x 01 04 49 00 00 00 0p FF
8x 01 04 4F 00 00 00 0p FF
8x 01 04 1F 0E 00 00 FF
8x 01 04 1F 0E 02 pp FF
8x 01 04 1F 0E 03 pp FF
8x 01 04 1F 4E 00 00 0p 0q FF
8x 01 04 1F 02 00 00 FF
8x 01 04 1F 02 02 pp FF
8x 01 04 1F 02 03 pp FF
8x 01 04 1F 42 00 00 0p 0q FF
8x 01 04 1F 21 00 00 0p 0q FF
8x 01 04 1F 21 01 00 0r 0s FF
8x 01 04 1F 49 00 00 0p 0q FF
8x 01 04 1F 4F 00 00 0p 0q FF
8x 01 04 14 0p 0q FF
8x 01 7E 04 7D 00 FF
8x 01 7E 04 7D 01 FF
8x 01 7E 04 7D 02 FF
8x 01 7E 04 7D 03 FF

Comments
pp: Interval Time [V cycle] 01h to FFh
mn: Register No. (=00h to 7Fh)
pq: Register Value (=00h to FFh)
mm: Threshold level
pp: Y fixed color for high-intensity
ss: Y fixed color for low-intensity
Each parameter setting 00h to 7Fh
Color Enhancement On/Off
p: Chroma Suppress setting level
00: Off
01h to 03h: On (3 levels).
Effect increases as the level number increases.
p: Color Gain Setting 0h (60%) to Eh (200%)
p: Color Hue Setting 0h (-14 degrees) to Eh (+14 degrees)
Exposure compensation reset
Exposure compensation up
pp: Step number
pp=00h to 7Fh (However, 00h is the same operation as 01h.)
Exposure compensation down
pp: Step number
pp=00h to 7Fh (However, 00h is the same operation as 01h.)
Set the exposure compensation to the specified level
pq: Level
pq=00h to FFh
Aperture control reset
Aperture control up
pp: Step number
pp=00h to 7Fh (However, 00h is the same operation as 01h.)
Aperture control down
pp: Step number
pp=00h to 7Fh (However, 00h is the same operation as 01h.)
Set the aperture control to the specified level
pq: Level
pq=00h to FFh
pq: ICR ON→OFF threshold level when Auto ICR
pq=00h to FFh
pq: ICR OFF→ON threshold level when Auto ICR
pq=00h to 16h
Color Gain Setting
pq: Gain setting level
pq=00h (0%) to FFh (200%)
Color Hue Setting
pq: Phase setting level
pq=00h (-14 degrees) to FFh (14 degrees)
p: HLC level (0: Off, 1: On)
q: HLC mask level (0: Off, 1: On)
—