Sony FCB-ER8550 Technical Manual page 16

Set PTZ Mask
Command: 8x 01 04 7B mm 0p 0p 0p 0q 0q 0q 0r 0r
0r 0r FF
Parameter:
mm Setting Mask
See "mm: Mask setting list" in "Parameters" on page 16.
ppp Pan Angle (000 to FFF)
See "Setting pan/tilt angle" in "Parameters" on page 16.
qqq Tilt Angle (000 to FFF)
See "Setting pan/tilt angle" in "Parameters" on page 16.
rrrr Zoom Position (000 to 4000)
See "Zoom Ratio and Zoom Position (for reference)" on
page 53.
Comments: Mask can be set at the desired position
by setting the pan tilt angle and zoom position
using this command. The set value can be input by
hexadecimal number.
Note
Privacy mask zone follows the change of angle of view according
to zoom. However, the follow might be delayed for a moment if
there is any big change, such as when using D-Zoom or E-FLIP.
Non Interlock Mask
Command: 8x 01 04 6F mm 0p 0p 0q 0q 0r 0r 0s 0s
FF
Parameters:
mm Setting Mask
See "mm: Mask setting list" in "Parameters" on page 15.
pp Sets the center position "x" of the Mask on screen.
qq Sets the center position "y" of the Mask on screen.
rr Sets the half value "w" of the Mask Width.
ss Sets the half value "h" of the Mask Height.
See "pp: x, qq: y, rr: w, ss: h" in "Parameters" on page 15.
Commands: Mask does not interlock with pan/tilt.
The limitations of parameters are as follows.
(hexadecimal representation)
x: ±50h
w: ±50h
y: ±2Dh
h: ±2Dh
Note
When the Set Mask command and the Non Interlock Mask
command are set to the same mask, the command set later
becomes effective.
Parameters
mm: Mask setting list
Mask Name mm (Hex)
Mask_A 00h
Mask_B 01h
Mask_C 02h
Mask_D 03h
Mask_E 04h
Mask_F 05h
Mask_G 06h
Mask_H 07h
Mask_I 08h
Mask_J 09h
Mask_K 0Ah
Mask_L 0Bh
nn:Setting
nn Setting
00h Resetting the zone size (the value of w,h)
for the existing mask.
01h Setting newly the zone size (the value of w,h).
pp: x, qq: y, rr: w, ss: h
90
B0h
Effective display area
Note
The priority order of the mask display is in the sequence from A
(highest) to X (lowest).
When you set the parameters of masks non-sequentially, it is
recommended that you set the mask whose priority order is higher,
first.
pp pp pp pp: Mask bit
pp
bit 7 6 5 4 3
Mask - - X W V U T S -
pp
bit 7 6 5 4 3
Mask - - L K J
The "-" must be "0".
1
Mask Name mm (Hex)
Mask_M 0Ch
Mask_N 0Dh
Mask_O 0Eh
Mask_P 0Fh
Mask_Q 10h
Mask_R 11h
Mask_S 12h
Mask_T 13h
Mask_U 14h
Mask_V 15h
Mask_W 16h
Mask_X 17h
160
2Dh
mask
h w
0 (x,y)
50h
D3h
pp
2 1 0 7 6 5 4 3 2 1 0
- R Q P O N M
pp
2 1 0 7 6 5 4 3 2 1 0
I H G - - F E D C B A