AMX AVB-TX-DGX-HD15-SC Fiber Quick Start Manual

Overview and Specifications
DGX Fiber Transmitters (TX) and Receivers (RX) are modules that work together or in
conjunction with DGX SC Fiber boards on an AMX AutoPatch DGX Distribution Matrix.
The transmitters feature Auto-Detect, and the receivers feature SmartScale™. This
Quick Start Guide contains basic installation information and specifications for the four
modules listed below. For complete information and specifications, see the DGX
Transmitters & Receivers Instruction Manual on the AMX AutoPatch CD or at
www.amx.com. For use with a DGX Distribution Matrix, see the product's Quick Start
Guide and/or Instruction Manual.
Front View
AVB-TX-DGX-HD15-SC Fiber
AVB-RX-DGX-SC Fiber-RGBHV
AVB-TX-DGX-DVI-SC Fiber
AVB-RX-DGX-SC Fiber-DVI
FIG. 1 DGX Fiber Transmitters and Receivers
Compatibility Note: DGX Fiber Transmitters and Receivers are not compatible with
third party optical distribution amplifiers or multimode to single-mode converters.
General Specifications and Product Information
Approvals
AC Power
Power Consumption (max.)
Thermal Dissipation (max.)
Power Connector*
Operational Temperature
Storage Temperature
Humidity
Dimensions
Weight / Shipping Weight
MTBF
Safety Certifications
(DGX DVI TX and DGX HD-15 TX)
Compatible AMX AutoPatch Fiber Products
Advanced Configuration Interface
Fiber Cable Type (SC Termination)
Fiber Cable Length
Optical Budget
Power Output of Laser Radiation (max.) 4.08 mW (DVI TX and HD-15 TX only)
Fiber Cable Connector
Analog Video and DVI Video
Resolution Support
Data Rate (max.)
Pixel Clock
Video Digital Processing
Input Interlaced Video Support
DDC/EDID Support
Analog Video Only
TX Input Signal Types
TX Auto-Adjust Input
TX Input and Local Output Connectors
RX Output Signal Type
RX Output Scaling
RX Output Connector
* A desktop power supply (ENERGY STAR
** 3,000 foot cable requires 50/125 μm OM2 class low loss fiber cable. Transmission distance
will vary (more or less) depending on the type/quality of fiber used, fiber bandwidth, cable bend
radius/kinks, splicing quality and quantity, and chromatic or modal dispersion.
Rear View
FG1010-200-01
FG1010-400-01
FG1010-210-01
FG1010-410-01
UL, cUL, CE, FCC Class A, RoHS
100 to 240 VAC single phase, 50 Hz to 60 Hz
0.6 A @ 115 VAC max.
+12 V, 1.25 A (15 W)
51 BTU/hr.
2.1 mm DC power jack
32° F to 113° F (0° C to 45° C)
-22° F to 158° F (-30° C to 70° C)
0 to 90% non-condensing
5.15 in. (13.08 cm) depth; 5.80 in. (14.73 cm) width;
1.66 in. (4.22 cm) height
Approximately 1.75 lb. (0.8 kg) / 2.75 lb. (1.25 kg)
92,000 hrs.
Class 1 Laser Product (Class 3R Laser Product when fiber
is disconnected from unit) IEC 60825-1, 2001
Other AMX AutoPatch DGX Signal Management products
USB Mini-B
μm
Multimode Simplex, 50/125 preferred or 62.5/125
μm
Up to 3000 ft. (914.4 m) with 50 cable**
μm
Up to 1500 ft. (457.2 m) with 62.5 cable
9.75 dBm (typical) between DGX TX and RX
Optical Modulation Amplitude (OMA): -6.25 dBm (typical)
OMA Sensitivity: -16.0 dBm (typical)
SC Optical
640x480 @ 60 Hz up to 1920x1200 @ 60 Hz
4.95 Gbps
25 MHz to 165 MHz
24 bit, 165 MHz
1080i 60, 59.94, 50 fields/sec.; 576i 100 fields/sec.
Analog video only 576i 50 fields/sec. and 480i 60 fields/sec.
Interlace video supported into the TX
Progressive only supported out of the RX
EDID provided by DGX TX (EDID is user re-programmable)
RGBHV, RGBS, RGsB, Y/Pb/Pr
Yes
HD-15 (RGBHV and Y/Pb/Pr)
RGBHV
SmartScale™, Presets, Manual Configuration
HD-15 (RGBHV)
®
qualified) is provided with each module.
AutoPatch DGX Fiber TX and RX Modules
DVI Video Only
TX Input and RX Output Signal Types
TX HDCP Support
TX Input and Local Output Connectors
RX Output Scaling
RX Output Connector
Input Cable Length
Audio – Analog and Digital
TX Input and RX Output Signal Types
TX Analog Input and RX Output Level (max.) +8 dBu, unbalanced
TX and RX S/PDIF Resolution
TX and RX S/PDIF Sample Rate
TX Analog to Digital Reference Level
RX Digital to Analog Reference Level
Audio Synchronization
Connectors
* 96 kHz audio only available for source video
Otherwise, 48 kHz is the maximum.
Serial Data
TX Input and RX Output Signal Type
(video must be present to pass data)
TX Input and RX Output Signal Level (max.) +/-15 V
TX and RX Baud Rate (max.)
TX and RX Baud Rate (typical)
TX Input and RX Output Connectors
EDID TX Standard Timing Identification
ID 1: 1920x1200 @ 60 Hz
ID 2: 1920x1080 @ 60 Hz
ID 3: 1680x1050 @ 60 Hz
ID 4: 1600x1200 @ 60 Hz
EDID TX Established Timing
640x480 @ 60 Hz, 67 Hz, 72 Hz, 75 Hz
800x600 @ 56 Hz, 60 Hz, 72 Hz, 75 Hz
1024x768 @ 60 Hz, 70 Hz, 75 Hz, 87 Hz
720x400 @ 70 Hz, 88 Hz
Module Installation
System Setup
μm
DGX TX Modules
The DGX DVI TX receives a DVI signal and the DGX HD-15 TX receives an analog
video signal.** Both TXs receive either a digital audio or an analog stereo audio
signal from the source device (digital takes precedence if both are connected). Video
and embedded audio and data signals are sent over an SC fiber cable to an RX module.
The RS-232 ports can supply unidirectional RS-232 serial data with the data flow in the
same direction as the video. Each TX also has a local video output connector.
** Supports RGBHV, RGBS, RGsB, or Y/Pb/Pr (Y/Pb/Pr up to 1080p) video formats.
DGX RX Modules
Each DGX RX accepts its video, audio, and data signals from a DGX TX via the fiber
cable, converts the video to either DVI or RGBHV (depending on the model), and sends
the signal to the destination. Audio on each RX will be output on both the digital and
analog stereo ports.
Control
Source Device
PC
USB
TX
FIG. 2 Typical system setup (use either model DGX TX with either model DGX RX)

Quick Start Guide

DVI-D (single link)
No
DVI-I (DVI-D single link is supported signal type)
SmartScale™, Presets, Manual Configuration
DVI-I (DVI-D single link is supported signal type)
Meets DVI spec of 5 m (16.4 ft.)
Stereo analog, S/PDIF (2 Channel L-PCM)
Video signal must be present to pass audio
16 bit to 24 bit
32 kHz, 44.1 kHz, 48 kHz, 96 kHz*
+8 dBu = 0 dBfs
0 dBfs = +8 dBu
Progressive and interlace video formats @ 60 Hz
frame rate. Audio is actively delayed to match video
within 8 ms leading or lagging.
RCA (S/PDIF) and 3.5 mm mini-stereo (analog) jacks
800x600@ 60Hz (40 MHz pixel clock) or greater.
Unidirectional RS-232, control signal transmitted
in the same direction as the video/audio
115.2 k baud, 25 ft. (7.6 m) copper cable
57.6 k baud, 150 ft. (45.7 m) copper cable
Pluggable 3.5 mm terminal block
(preferred timing identified in EDID)
832x624 @ 75 Hz
1280x1024 @ 75 Hz
1152x870 @ 75 Hz
For setup only for systems
with special requirements Destination
(see manual)
USB
RX
Local Video
Output
SC fiber up to 3000 ft. (914 m)
ID 5: 1280x800 @ 60 Hz
ID 6: 1280x720 @ 60 Hz
ID 7: 1280x1024 @ 60 Hz
ID 8: 640x480 @ 120 Hz
–
Device