1. Manuals
  2. Brands
  3. Nordic Semiconductor Manuals
  4. Microcontrollers
  5. nRF8002
  6. User manual

Nordic Semiconductor nRF8002 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
nRF8002 Development Kit
User Guide.v1.0
All rights reserved.
Reproduction in whole or in part is prohibited without the prior written permission of the copyright holder.
2012-2-23

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the nRF8002 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Nordic Semiconductor nRF8002

Summary of Contents for Nordic Semiconductor nRF8002

  • Page 1 Development Kit User Guide.v1.0 All rights reserved. Reproduction in whole or in part is prohibited without the prior written permission of the copyright holder. 2012-2-23...
  • Page 2 Development Kit User Guide Liability disclaimer Nordic Semiconductor ASA reserves the right to make changes without further notice to the product to improve reliability, function or design. Nordic Semiconductor ASA does not assume any liability arising out of the application or use of any product or circuits described herein.

  • Page 3: Table Of Contents

    Key features ..................8 4.1.2 nRF8002 module (nRF2748)............8 4.1.3 Inputs and Outputs ................10 4.1.4 Buzzer (PWM output) and nRF8002 current measurement .....11 4.1.5 I/O pin header...................12 4.1.6 nRFgo Starter Kit Motherboard (nRF6310) extension connectors ...13 µBlue Master Emulator (nRF2739) ............14 4.2.1 Module schematics and PCB layouts..........14...

  • Page 4: Introduction

    By uploading the default configuration in nRFgo Studio, a nRF8002 Development Kit can be used to demonstrate nRF8002 features using the µBlue Master Emulator and the Proximity Demo application provided with this kit. The kit also allows you to track and control the traffic between the nRF8002 device and a master.

  • Page 5: Development Kit Content

    Development Kit User Guide Development Kit content The nRF8002 Development Kit consists of hardware and software components, and a Proximity Demo application. Hardware content Figure 1. Hardware Content 2.1.1 nRF8002 module (nRF2748) The nRFready nRF8002 (nRF2748) includes: • Fully functional Bluetooth low energy proximity tag •...

  • Page 6: Software Content

    Development Kit User Guide Software content From the www.nordicsemi.com website you can download the nRF8002 Proximity Demo installation file and the nRFgo Studio. Documentation Documentation for this Kit can be downloaded from www.nordicsemi.com and includes: • This User Guide •...

  • Page 7: Test Rf Parameters Using Direct Test Mode (Dtm)

    Testing the physical layer on your product nRF8002 can only enter DTM before it has been configured with a setup. This means that in order to test your own product, leave nRF8002 unconfigured and go to the Features pane in nRFgo Studio, select Bluetooth and then select Direct Test Mode.

  • Page 8: Hardware Description

    This chapter describes the nRF8002 (nRF2748) module and the µBlue Master Emulator (nRF2739). nRF8002 can be configured to respond to different pin pattern input and to issue different pattern output depending on activity in the embedded Bluetooth low energy services and profiles. Use nRFgo Studio to change and upload new configurations to adjust the nRF8002 behavior.
  • Page 9 Development Kit User Guide Figure 3. nRF2748 bottom view Revision 1.0 Page 9 of 16...

  • Page 10: Inputs And Outputs

    The button SW1 is routed to signal IN1 • The button SW2 is routed to IN2 In addition, nRF8002 has three digital outputs and a PWM output. The three digital output signals are routed to three LEDs in the following way: •...

  • Page 11: Buzzer (Pwm Output) And Nrf8002 Current Measurement

    Replace this jumper with a 5-10 ohm resistor and use an oscilloscope to measure nRF8002 current consumption. See the nRF Performance Test Guidelines (nWP-006) on our website for details on how to measure dynamic current.

  • Page 12: I/O Pin Header

    Table 1.Pinouts for I/O header P3 To directly access the I/O pins of the nRF8002 device, an optional pin header P3 (not mounted) is available. This pin header is populated with all of the inputs, outputs, and the PWM signal available on the nRF8002.

  • Page 13: Nrfgo Starter Kit Motherboard (Nrf6310) Extension Connectors

    Note: Only P1 carries the input and output resources to nRF2748. P2 carries only the power support and the BoardID interface. You can download nRF8002 Development Kit hardware schematics and PCB layout files from www.nordicsemi.com. Page 13 of 16...

  • Page 14: Μblue Master Emulator (Nrf2739)

    µBlue Master Emulator (nRF2739) The µBlue Master Emulator (nRF2739) is a dongle that enables you to use the Proximity Demo Application with nRF8002. The µBlue Master Emulator is a peer device for nRF8002 allowing you to set up the wireless connection.

  • Page 15: Block Diagram

    4.2.2 Block diagram Figure 9. is a block diagram and description of the main parts of nRF8002 including the radio, configuration interface, Starter Kit Motherboard (nRF6310) integration, and pin header for extended I/O usage. Figure 9. nRF8002 Block diagram Page 15 of 16...

  • Page 16: Troubleshooting

    Development Kit User Guide Troubleshooting The nRF8002 on the SoC module (nRF2748) does not respond when I try to contact it. What has happened? Verify that the jumper JP5 is connected. LED D0 on the µBlue Master Emulator (nRF2739) does not light up when I plug in the USB cable.

Table of Contents