Advertisement
STEP 6B MGR-2 channel two code setting
The pushbutton labeled S2 is used to program transmitters to channel two.
CHANNEL TWO
PUSHBUTTON
S2
S2
S1
USE THIS
PUSHBUTTON
TO ENTER
TRANSMITTERS
INTO CHANNEL
TWO
STEP 8
Add additional transmitters
Repeat Step 7 for each transmitter used with this receiver. Be sure to press the
receiver's program button each time a new transmitter or a different transmitter
button on a multi-button transmitter is pressed. If the LED doesn't come on when
the receiver's program button is pressed, the receiver's memory is full (40 transmitters
total). Use the erase function (Info 1) to remove transmitters from the receiver's
memory.
PRESS
PROGRAM
BUTTON FIRST
THEN PRESS
TRANSMITTER
BUTTON
S2
S1
INFO 1
Erasing receiver memory
Transmitters may be erased from the receiver's memory by pressing and holding the
receiver's program button until the LED blinks (count of transmitters) and then blinks
one more time (Channel 1) or two more times (Channel 2) as the receiver's memory
is erased. All transmitters are erased at the same time. Then release the program
button.
S2
S1
PRESS PROGRAM BUTTON
LED WILL FLASH, COUNTING THE
FOR FIVE SECONDS OR
TOTAL NUMBER OF TRANSMITTERS
MORE
PROGRAMMED. THEN IT WILL
BLINK ONCE (CHANNEL ONE) OR
TWICE (CHANNEL TWO) AS THE
TRANSMITTERS ARE ERASED
STEP 7
Program the receiver
Momentarily press the receiver's program button. The red programming LED will light
if there's room in the receiver's memory for another transmitter (40 maximum per
receiver). The LED stays on for about 5 seconds. A transmitter must be entered
while the LED is on. Press the desired transmitter button. The LED will flicker
indicating that the receiver has accepted the transmitter
➥ NOTE: be sure to press the receiver program button for less than 2 seconds.
➥ WARNING! Operator will not activate when the receiver is being
programmed from the transmitter, but will activate the next time the
transmitter is activated after programming.
➥ NOTE: The programming LED also monitors radio signals entering the
receiver. It is common to see an occasional blink from the LED. The LED
will also light when any transmitter tuned to the receiver's frequency
(programmed into the receiver or not) is activated.
STEP 9
Review memory
Press and hold the receiver's program button until the LED begins to flash (about 3
seconds) and then release the button. Count the number of flashes. The number of
flashes equals the number of transmitters programmed into the receiver
➥ NOTE: Don't hold down the programming button longer than 5 seconds
or the receiver's memory for that channel will be erased (Info 1).
S2
S1
WITH MULTI-BUTTON
PRESS PROGRAM BUTTON
TRANSMITTERS,
FOR THREE SECONDS
PRESS THE DESIRED
THEN RELEASE
BUTTON
LIMITED WARRANTY
This Linear product is warranted against defects in material and
workmanship for twelve (12) months. The Warranty Expiration Date is
labeled on the product. This warranty extends only to wholesale customers
who buy direct from Linear or through Linear's normal distribution
channels. Linear does not warrant this product to consumers. Consumers
should inquire from their selling dealer as to the nature of the dealer's
warranty, if any. There are no obligations or liabilities on the part of Linear
LLC for consequential damages arising out of or in connection with use or
performance of this product or other indirect damages with respect to loss of
property, revenue, or profit, or cost of removal, installation, or reinstallation. All
implied warranties, including implied warranties for merchantability and
S2
implied warranties for fitness, are valid only until Warranty Expiration
S1
Date as labeled on the product. This Linear LLC Warranty is in lieu of all
other warranties express or implied.
All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Services at
1-800-421-1587 for an RPA# and other important details
MOMENTARILY PRESS
THE PUSHBUTTON
FOR THE DESIRED
CHANNEL (S1 or S2)
THE LED WILL
LIGHT AND REMAIN
ON ABOUT FIVE
SECONDS
STEP 10 Test receiver
Be sure gate area is clear. Activate each transmitter. The receiver relay should click
and the operator should activate. Wait 1 second between each activation.
S2
WARNING!
BE SURE GATE
S1
AREA IS CLEAR
OF OBSTRUCTIONS
LED WILL FLASH, COUNTING THE
NOTE: If the receivers LED flashes continuously when a transmitter isn't being
TOTAL NUMBER OF TRANSMITTERS
activated, the receiver is too close to an electrical noise source. Move the
PROGRAMMED
receiver away from the noise source or call technical services for assistance.
(The receiver must be open to observe this.)
Linear radio controls provide a reliable communications link and fill
an important need in portable wireless signaling. However, there are
some limitations which must be observed.
✶ For U.S. installations only: The radios are required to comply with FCC Rules
and Regulations as Part 15 devices. As such, they have limited transmitter
power and therefore limited range.
✶ A receiver cannot respond to more than one transmitted signal at a time
and may be blocked by radio signals that occur on or near their operating
frequencies, regardless of code settings.
✶ Changes or modifications to the device may void FCC compliance.
✶ Infrequently used radio links should be tested regularly to protect against
undetected interference or fault.
✶ A general knowledge of radio and its vagaries should be gained prior to acting
as a wholesale distributor or dealer, and these facts should be communicated
to the ultimate users.
Copyright © 2005 Linear LLC
WHEN RECEIVER
IS READY, PRESS THE
DESIRED TRANSMITTER
BUTTON
S2
S1
RECEIVER LED
WILL FLICKER
AS TRANSMITTER
IS ENTERED INTO
MEMORY
PRESS TRANSMITTER
BUTTON TO TEST
IMPORTANT!!!
225820 A
Advertisement
