Related Manuals for Triax 383101
Summary of Contents for Triax 383101
- Page 1 User Manual Ethernet over COAX Controller / Endpoint / RP filter Article Article no. 383101 383103 Ethernet over COAX Controller / Endpoint / RP filter 383200 383900 Version Date 09/2018...
-
Page 2: Table Of Contents
Ethernet over COAX Safety Instructions ............................... 2 The EoC solution – unmanaged or managed via In Touch ................ 3 Overview of components........................4 EoC Controller ............................4 EoC Endpoint............................5 EoC Return path (RP) filter ........................5 Standard configuration groups ........................6 Initial Setup ............................6 Private only ............................6 Guest only .............................6 Guest and Private ..........................6... -
Page 3: Safety Instructions
Ethernet over COAX Safety Instructions ATTENTION Failure to comply with the specified precautionary measures may cause serious injury to persons or damage to property. The installation and commissioning may only be performed by suitably qualified persons, technicians or installers in compliance with safety regulations. Damage due to improper installation and commissioning, defective connectors on cables or any other incorrect handling will void the warranty. -
Page 4: The Eoc Solution - Unmanaged Or Managed Via In Touch
With this solution the user is given raw WiFi. EoC can also be used in combination with a TRIAX In Touch managed solution to add layer 3 functionality. This gives the user a managed In Touch solution where the WiFi bandwidth per device can be controlled; as well as providing a range of value added services. -
Page 5: Overview Of Components
Ethernet over COAX Overview of components To install the EoC controller and endpoints it is recommended to use the following process: Start with the controller Then install endpoints Use the controller interface to Mount the backplate of the endpoint ... -
Page 6: Eoc Endpoint
Ethernet over COAX EoC Endpoint EoC Return path (RP) filter... -
Page 7: Standard Configuration Groups
Ethernet over COAX 2. Standard configuration groups The EoC controller and the endpoint comes with standard configuration groups. These can be used if you do not need any further WiFi SSIDs or configuration of ethernet ports. The standard configuration can be used in any The standard configuration on the controller is as network where there is a need for follows... -
Page 8: How To Connect Standard Configuration Groups
Ethernet over COAX 3. How to connect standard configuration groups Private network Guest network Connect a CAT cable from your router/modem to Connect a CAT cable from your router/modem to port 2 on the controller. port 3 on the controller. This will allow any endpoint with the “Private only”... -
Page 9: Endpoint Setup
Ethernet over COAX 5. Endpoint setup Operation Each endpoint has two RF ports, EoC + TV and TV out. The EoC + TV port communicates using network (data) signals on 2-200 MHz and receives TV signals on 300-862 MHz. The endpoint splits the signals into network data, accessible through ethernet and WiFi, and TV out. LEDs on endpoint Signal Status... -
Page 10: Controller Interface
Ethernet over COAX 6. Controller interface It is possible to access the web interface by connecting a PC via ethernet to port 1 on the controller. Open a browser and type in http://setup.eoc and type in the admin username and password. By default this is admin/admin, but is usually changed through the configuration wizard. -
Page 11: Network
Ethernet over COAX Network Change of settings of the network infrastructure, including the coax data connection. Management settings Apart from the default controller management interface on ethernet port 1 (setup VLAN 10), it is possible here to allow management access through an additional VLAN (ethernet port) of your choice. Furthermore, you can configure IPv4 settings used for management. - Page 12 Ethernet over COAX Network Access VLAN Trunk VLAN All inbound traffic that does not already All: Traffic tagged with any VLAN created have a VLAN tag will be tagged with the in “VLAN settings” is allowed through the access VLAN.
-
Page 13: System
Ethernet over COAX Network Endpoint settings It is possible to see all endpoints configured on the controller. Endpoints which has just been connected will get the configuration from the Setup group, which means that they will broadcast a WiFi SSID called TriaxSetup_xxxx and the ethernet port can be used to connect to the controller interface. -
Page 14: Performance
It is then possible to choose a configuration group for this specific endpoint and write in a name and/or location. 8. Support To get support, please access our support sites at http://www.triax.com/b2buserregister You have to be a registered user in order to log in. - Page 15 Notes-Notizen-Notes-Notas-Notater...
- Page 16 Peut être sujet à modification sans préavis Copyright © 2018 TRIAX. All rights reserved. The TRIAX Logo and TRIAX Multimedia are registered trademark(s) of the TRIAX Company or its affiliates. TRIAX A/S | Bjørnkærvej 3 | 8783 Hornsyld | Denmark...