Dahua DH-TPC-SD8620-B Quick Start Manual
  1. Manuals
  2. Brands
  3. Dahua Manuals
  4. Security Camera
  5. DH-TPC-SD8620-B
  6. Quick start manual
Dahua DH-TPC-SD8620-B Quick Start Manual

Dahua DH-TPC-SD8620-B Quick Start Manual

Thermal hybrid speed dome camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Thermal Hybrid Speed Dome
Quick Start Guide
Version 2.0.0

Advertisement

Table of Contents
loading

Related Manuals for Dahua DH-TPC-SD8620-B

Summary of Contents for Dahua DH-TPC-SD8620-B

  • Page 1 Thermal Hybrid Speed Dome Quick Start Guide Version 2.0.0...

  • Page 2: Table Of Contents

    Table of Contents CYBERSECURITY RECOMMENDATIONS .............. III PACKING LIST ....................1 DEVICE STRUCTURE ..................2 Device External Cable .......................... 2 Structure Dimension ..........................3 DEVICE INSTALLATION ..................6 Installation Preparation ......................... 6 3.1.1 Check Installation Space and Intension ..................6 3.1.2 About cable ............................
  • Page 3 Welcome Thank you for purchasing our thermal hybrid speed dome!

  • Page 4: Cybersecurity Recommendations

    Please read the following safeguards and warnings carefully before you install or use the product! Cybersecurity Recommendations Mandatory actions to be taken towards cybersecurity 1. Change Passwords and Use Strong Passwords:...
  • Page 5 The number one reason systems get “hacked” is due to having weak or default passwords. It is recommended to change default passwords immediately and choose a strong password whenever possible. A strong password should be made up of at least 8 characters and a combination of special characters, numbers, and upper and lower case letters.
  • Page 6 In the event that your social media, bank, email, etc. account is compromised, you would not want someone collecting those passwords and trying them out on your video surveillance system. Using a different username and password for your security system will make it more difficult for someone to guess their way into your system.
  • Page 7 Important Safeguards and Warnings Safety Measures 1. Qualified Engineer Needed  The installation engineer or maintenance engineer shall have corresponding CCTV system installation certificate or maintenance qualification certificate.  The installation engineer or maintenance engineer shall have qualification certificate for work at height.
  • Page 8 2. Lifting Appliance Requirement  Please select the proper thermal hybrid dome installation mode and use the lifting appliances at the safety environment.  The lifting appliances shall have the enough capacity to reach the installation height.  The lifting appliances shall have safe performance. The precaution measures include two types: Warning and Note.
  • Page 9 2. When device is malfunction Shut down the device and disconnect the power cable immediately if there is smoke, abnormal smell or abnormal function. Please contact your local retailer ASAP. 3. Do not try to dismantle or modify the device ...
  • Page 10 About the Guide  The Guide is for reference only. If there is inconsistency between the Guide and the actual product, the actual product shall prevail.  We are not liable for any loss caused by the operations that do not comply with the Guide. ...
  • Page 11 FCC Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC conditions: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: ...

  • Page 12: Packing List

    1 Packing List Please check if there is any obvious damage to the device appearance when opening the packing box, and confirm if the accessories in the box are in accordance with those on the list. Please refer to Table 1-1 for more details about the list. Accessory Name Quantity Thermal Hybrid Speed Dome...

  • Page 13: Device Structure

    2 Device Structure 2.1 Device External Cable Note  The following figure is for reference only, which is only used to know the function of cable ports.  The cable structure may be different according to different devices, please refer to the actual device for more details.

  • Page 14: Structure Dimension

    Port Cable port name Function description Alarm output port 1, output alarm signal to alarm ALARM_OUT1 device. Note ALARM_OUT1 can only be used with ALARM_COM1 ALARM_COM1 when connecting to alarm device. Alarm output port 2, output alarm signal to alarm ALARM_OUT2 device.
  • Page 15 Figure 2-2 Please refer to Figure 2-3 for the dimension of wall-mounted bracket. The unit is mm (inch). Figure 2-3 Please refer to Figure 2-4 for the dimension of hang-mounted bracket. The unit is mm (inch).
  • Page 16 Figure 2-4 Please refer to Figure 2-5 for the dimension of corner-mounted bracket. The unit is mm (inch). Figure 2-5 Please refer to Figure 2-6 for the dimension of pole-mounted bracket. The unit is mm (inch). Figure 2-6...

  • Page 17: Device Installation

    3 Device Installation 3.1 Installation Preparation 3.1.1 Check Installation Space and Intension Please make sure the installation environment has enough space to install the thermal hybrid speed dome and its corresponding bracket. Please make sure the ceiling and wall where the device is installed can support the thermal hybrid dome and its corresponding installation component.

  • Page 18: Installation Steps

    Figure 3-1 Note Press the reset button for 4s~5s and then it can realize device factory default settings. Step 2 Insert the SD card into the slot, the card slot is elastic, so you only need to press the SD card slightly to install the SD card.
  • Page 19 Step 1 Fix the device on the wall. 1. Dig holes on the mounting wall, fix the expansion bolt, and tighten the hex nut, as it is shown in Figure 3-2 ①. 2. Twist the quick mounting connector into the wall-mounted bracket and use stainless screws to fix it, which is shown in Figure 3-2 ②.

  • Page 20: Hang-Mounted Installation

    Figure 3-3 1. Keep the convex groove outward and install the rubber ring into the network port, keep the smaller hole of the rubber ring outward and install the fixing rubber ring into the main body of the waterproof connector. 2.

  • Page 21: Corner-Mounted Installation

    2. Pull the cable through the connection pole, twine the Teflon tape around the connection pole and fix it on the connection tray, as it is shown in Figure 3-4 ②. 3. Twist the quick mounting connector into the wall-mounted bracket, use stainless screws to fix, buckle the safety hook, connect cable and use insulated tape to make it waterproof, which is shown in Figure 3-4 ③.

  • Page 22: Pole-Mounted Installation

    3. Buckle the safety hook, connect cable and use insulated tape to make it waterproof. Pull the cable into the wall-mounted bracket and use stainless screws to fix the speed dome on the bracket. Caution Please make sure the safety hook is installed, otherwise the thermal hybrid dome may fall and cause accident due to instability! Please refer to the safety hook installation instruction in the accessories bag for more details.
  • Page 23 1. Fix the mounting hoop and pole-mounted bracket on the pole, and paste glass cement on it to make it sealed and waterproof, which is shown in Figure 3-6 ①. 2. Twist the quick mounting connector into the wall-mounted bracket and use stainless screws to fix it.

  • Page 24: Device Configuration

    4 Device Configuration 4.1 Device Initialization It needs to set the user password when logging in for the first time (the username is admin by default). The figures listed in the following chapter are for reference only. There is difference about interface between different devices, please refer to the actual device for more details.

  • Page 25: Modify Ip Address

    Step 3 Click Save to complete initialization. 4.2 Modify IP Address In order to make the camera get access to network smoothly, please plan IP address reasonably according to the actual network environment. Step 1 Log in camera WEB interface in the IE browser. Note ...

  • Page 26: Alarm Setup

    Note  IP address is the one which has been modified.  Default user is admin; the password has been set during device initialization. Step 2 Click Login and the system will display the WEB main interface, which is shown in Figure 4-3. Note It will prompt you to install plug-in for the first system login, please save and install plug-in according to prompt.
  • Page 27 Step 4 Make corresponding settings upon alarm input and output in the alarm setup interface, and then click Save. The interface of alarm setup is shown in Figure 4-4.  Alarm input is corresponding to the alarm input port of device I/O cable. It is to set corresponding NO and NC according to the high and low level signal generated by alarm input device when alarm occurs.
  • Page 28 Figure 4-6 Alarm output: port ALARM_OUT and ALARM_COM form a switch, which can be used to provide alarm output. Normally the switch is on, the switch will be off when there is alarm output.

  • Page 29: Appendix Ⅰ Lightening Protection And Surge Protection

    5 Appendix Ⅰ Lightening Protection and Surge Protection This series thermal hybrid dome adopts TVS lighting protection technology. It can effectively prevent damages from various pulse signals below 4000W, such as sudden lighting and surge. While maintaining your local electrical safety code, you still need to take necessary precaution measures when installing the thermal hybrid dome in the outdoor environment.
  • Page 30 Note  This manual is for reference only. Slight difference may be found in the user interface.  All the designs and software here are subject to change without prior written notice.  All trademarks and registered trademarks are the properties of their respective owners. ...

Table of Contents