Control Panel - Caple ST852 Instruction Manual

Essential precautions to respect before installing
Essential precautions to respect before installing
the appliance are below:
the appliance are below:
- Make a cut-out in the bottom of the cabinet
- Make a cut-out in the bottom of the cabinet
which is suitable to hold the appliance in position which is suitable to hold the appliance in position
(see fig.4). (see fig.4).
- Prepare the power supply.
- Prepare the power supply.
- Prepare a hole for the exhaust of the air, this
- Prepare a hole for the exhaust of the air, this
is both for the recirculated and in the ducted
is both for the recirculated and in the ducted
installation. installation.
Before installing the appliance, make sure that none
Before installing the appliance, make sure that none
of the parts are damaged in any way. In case of any
of the parts are damaged in any way. In case of any
damaged parts, please contact your retailer and
damaged parts, please contact your retailer and
do not proceed with installation.
do not proceed with installation.
Read all of the following instructions with care Read all of the following instructions with care
before installing the appliance. before installing the appliance.
- Use an air outlet pipe of the shortest possible
- Use an air outlet pipe of the shortest possible
length.
length.
- Limit the number of pipe bends.
- Limit the number of pipe bends.
- Use a material approved by standards and - Use a material approved by standards and
regulations. regulations.
- Avoid any sudden changes in pipe section.
- Avoid any sudden changes in pipe section.
- The recommended constant ducting diameter is
- The recommended constant ducting diameter is
150mm/200 mm (or equal surface area). Do not
150mm/200 mm (or equal surface area). Do not
use less than 150mm ducting.
use less than 150mm ducting.
To install the appliance, adjust the position of the
To install the appliance, adjust the position of the
stop side-springs using the appropriate screws
stop side-springs using the appropriate screws
(fig.5), according to the thickness of the board
(fig.5), according to the thickness of the board
previously drilled, on which the appliance will be previously drilled, on which the appliance will be
fixed. fixed.
Insert the built-in unit in the hole made in the
Insert the built-in unit in the hole made in the
cabinet until the stop click of the side springs is
cabinet until the stop click of the side springs is
heard and the built-in unit is locked. Insert the
heard and the built-in unit is locked. Insert the
screws provided in the holes inside the appliance
screws provided in the holes inside the appliance
(fig.6) to fully lock it in position. (fig.6) to fully lock it in position.
Refit the grease filter/s Refit the grease filter/s
Ensure the stop valve is not blocked and can freely
Ensure the stop valve is not blocked and can freely
move.
move.
Warning!
Warning!
Before connecting the flexible exhausting pipe to
Before connecting the flexible exhausting pipe to
the motor, make sure the stop valve, which is on
the motor, make sure the stop valve, which is on
the air outlet of the motor, can swing and is not
the air outlet of the motor, can swing and is not
blocked. blocked.
Ducted install
Ducted install
Connect the flange to the exhausting hole with an
Connect the flange to the exhausting hole with an
appropriate pipe. Connect the appliance to the
appropriate pipe. Connect the appliance to the
electrical mains with the supply cord. electrical mains with the supply cord.
Recirculated install
Recirculated install
Connect the flange with a pipe suitable to
Connect the flange with a pipe suitable to
convey the air to the top of the cabinet. Connect
convey the air to the top of the cabinet. Connect
the appliance to the electrical mains with the
the appliance to the electrical mains with the
supply cord.
supply cord.
Rear vented version
These models can be rear vented. If you want to

Control panel

use this option, it is necessary to remove the 18
screws from the motor group support. Then take
the metal support with motor included out (pic.
11). Turn the motor to have the air outlet on
Refer to (Fig. 9)
the rear side (pic. 12) and then fix the scews
A: Light switch on/off
previously removed.
B: Motor switch on speed 1/off C:
Motor switch on speed 2 D: Motor
switch on speed 3 E: Motor switch
on speed 4 F: 10-minutes timer
Control panel
Refer to (Fig. 9)
A: Light switch on/off
Maintenance Maintenance
B: Motor switch on speed 1/off C:
Motor switch on speed 2 D: Motor
switch on speed 3 E: Motor switch
- An accurate maintenance helps guarantee good - An accurate maintenance helps guarantee good
on speed 4 F: 10-minutes timer
functioning and long-lasting performance.
functioning and long-lasting performance.
- Particular care is required for the grease filter
- Particular care is required for the grease filter
TIMING
panel. It can be removed by pushing its handle panel. It can be removed by pushing its handle
As a result of the new EU65 "Energy label"
toward the back-side of the cooker hood and toward the back-side of the cooker hood and
and EU66 " Ecodesign" regulations issued by
pulling the filter downwards to unfasten it from
pulling the filter downwards to unfasten it from
the European Commission, which came into
its slot (Fig.3).
its slot (Fig.3).
force as from January 1st, 2015 , our products
To insert the filter just perform the opposite
To insert the filter just perform the opposite
have been adapted to comply with these
operation. operation.
new requirements.
After 30 hours working, the push button After 30 hours working, the push button
All of the models complying with the energy
control panel will signal the saturation of the control panel will signal the saturation of the
label requirements, are equipped with
grease filter by illuminating all the buttons. Press
grease filter by illuminating all the buttons. Press
new electronics including a timer device
the timer button to reset
the timer button to reset
for suction speeds control, when the air capacity
The grease filter needs cleaning by regular
The grease filter needs cleaning by regular
exceeds 650m³/h.
hand-washing or in your dishwasher at least hand-washing or in your dishwasher at least
Internal motor models, with maximum air
every two months or more depending on its use. every two months or more depending on its use. capacity higher than 650m³/h, are equipped
with a timer device that automatically
switches the suction speed from 4th to 3rd
- In case the appliance is used in its recirculating
- In case the appliance is used in its recirculating
speed, after 6 minutes operation.
mode, the active charcoal filter (Fig.7) needs to be
mode, the active charcoal filter (Fig.7) needs to be
The energy consumption of the appliance in
periodically replaced. The charcoal filter can be periodically replaced. The charcoal filter can be
stand – by mode is lower than 0.5W.
removed by removing the grease filter first (Fig.3), removed by removing the grease filter first (Fig.3),
and by pulling its special plastic tongue until it is and by pulling its special plastic tongue until it is
unfastened from its slot. Re-insert the charcoal
unfastened from its slot. Re-insert the charcoal
filter by operating in the opposite way.
filter by operating in the opposite way.
The charcoal filter needs replacing depending on
The charcoal filter needs replacing depending on
the use, but at least every six months. the use, but at least every six months.
6
6
.
.