iTOOLco Cannon 12K User Manual
  1. Manuals
  2. Brands
  3. iTOOLco Manuals
  4. Tools
  5. Cannon 12K
  6. User manual

iTOOLco Cannon 12K User Manual

Hide thumbs Also See for Cannon 12K:
Table of Contents

Advertisement

Quick Links

User's Guide
100 MECO LANE | OAK RIDGE, TN 37830 | 865.483.2040 | ITOOLCO.COM
© 2018 PROPERTY OF ITOOLCO

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Cannon 12K and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for iTOOLco Cannon 12K

Summary of Contents for iTOOLco Cannon 12K

  • Page 1 User’s Guide 100 MECO LANE | OAK RIDGE, TN 37830 | 865.483.2040 | ITOOLCO.COM © 2018 PROPERTY OF ITOOLCO...

  • Page 2: Table Of Contents

    Overhead Wire Pull ........................... 18 Pulling Out Extra Wire ........................19 Receiver Hitch Wire Pulls ........................20 Maintenance ............................. 20 Specifications ............................ 20 LIMITED WARRANTY: ITOOLCO CANNON 12K ..................21 ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 2...

  • Page 3: Safety First

    Hazards that, if not avoided, COULD result in severe injury or death. CAUTION Hazards or unsafe practices that, if not avoided, MAY result in injury or property damage. ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 3...

  • Page 4: Important Safety Information

    FAILURE TO OBSERVE THESE WARNINGS CAN RESULT IN SEVERE INJURY OR DEATH WARNING – PERSONAL SAFETY HAZARDS Only qualified persons should use iTOOLco Cannon 12K. Wear eye protection and hard hat when using this tool. Do not use this tool while tired or under the influence of drugs, alcohol, or medication.
  • Page 5 Always plug into a grounded receptacle with a 20 amp GCFI protected circuit. Do not modify plug provided. Always disconnect cable puller before servicing. FAILURE TO OBSERVE THESE WARNINGS CAN RESULT IN SEVERE INJURY OR DEATH. (CONTINUED) ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 5...
  • Page 6 Do not use an extension cord longer than 100’. Extension cord should be a minimum of 12 gauge wire with ground. FAILURE TO OBSERVE THESE WARNINGS CAN RESULT IN SEVERE INJURY OR DEATH. ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 6...
  • Page 7 The pulling rope must come in contact with all the sheaves used in the boom system. FAILURE TO OBSERVE THESE WARNINGS CAN RESULT IN SEVERE INJURY OR DEATH. ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 7...

  • Page 8: Description And Identification

    The ITOOLco Cannon 12K is a 12,000 lb. cable puller intended to pull medium to large wire through conduit. It sets up in only minutes, and is a dual capstan, four-speed puller. The Cannon 12K can pull at speeds up to 36 feet per minute. It does not need to be anchored to the ground, and is easy for one person to set up, transport, and operate.
  • Page 9 ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 9...
  • Page 10 ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 10...
  • Page 11 ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 11...
  • Page 12 ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 12...
  • Page 13 ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 13...
  • Page 14 ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 14...

  • Page 15: Set Up And Operation

    3. Insert 5 conduit adapters into base unit. 4. If necessary, install axle and wheels onto base. 5. iTOOLco Cannon 12K is designed to be used with a 20 amp, 6 speed coring motor. 6. Plug in the foot switch to the 100 volt power supply.

  • Page 16: Attaching Conduit Adapters

    Tighten the 1/2” bolt on the side of the head body. See Figure 7. 3. Remove the adjustment hitch pin. Slide the puller into position and place the conduit adapter into the conduit. See Figure 8. 4. Replace all hitch pins. ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 16...

  • Page 17: Underground Wire Pull

    Do not exceed about 45 N (10 lbs.) of tension on the rope. If the pull becomes difficult, add another wrap or two of rope to the capstan. If excessive force becomes necessary, stop the pull and inspect the set up. ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 17...

  • Page 18: Overhead Wire Pull

    Overhead Wire Pull 1. Convert the Cannon 12K to an overhead configuration by removing the cinch pin at the main knuckle. Pull the snap pin, and rotate the front end right or left to the desired position. 2. To achieve optimum balance, slide base to adjust the front knuckle weight.

  • Page 19: Pulling Out Extra Wire

    2. Separate the front knuckle from the main knuckle. 3. Place extensions in line. 4. Then slide the extension over the extension tube. 33” and 15” Extensions Store Right on the Cannon 12K ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 19...

  • Page 20: Receiver Hitch Wire Pulls

    4. Secure puller to receiver hitch with hitch pin. Maintenance Gear box is filled with high-temperature synthetic gear lubricant. No maintenance is required. Always make sure that Cannon 12K is clean and in good working order before use. Replace any worn rollers or rusty pins before use. Specifications Length (fully extended) 188”...

  • Page 21: Limited Warranty: Itoolco Cannon 12K

    If the part(s) if found to be defective, iTOOLco will refund freight charges paid by you in retuning the defective part(s) and prepay replacement part(s) freight charges.
  • Page 22 100 MECO LANE | OAK RIDGE, TN 37830 | 865.483.2040 | ITOOLCO.COM © 2018 PROPERTY OF ITOOLCO ITOOLCO CANNON 12K USER’S GUIDE 1801C12KUG P a g e | 22...

Table of Contents