Related Manuals for SMA BLUETOOTH PIGGY-BACK PLUS
Summary of Contents for SMA BLUETOOTH PIGGY-BACK PLUS
- Page 1 Communication Interface for SMA Inverters ® SMA BLUETOOTH PIGGY-BACK PLUS Installation Guide BTPB-Ant-IEN111510 | 98-0032110 | Version 1.0...
-
Page 3: Table Of Contents
SMA Solar Technology AG Table of Contents Table of Contents Information on this Manual......5 Safety ......... . 6 Appropriate Usage . - Page 4 Table of Contents SMA Solar Technology AG Technical Data ........27 Bluetooth Piggy-Back .
-
Page 5: Information On This Manual
Undesired result. Followed by a solution on how to achieve the desired result. Nomenclature • This manual refers to PV plants and small wind turbine systems collectively as "plants." • In this manual the SMA Bluetooth Piggy-Back Plus is referred to as Bluetooth Piggy-Back. Installation Guide BTPB-Ant-IEN111510... -
Page 6: Safety
2.1 Appropriate Usage The Bluetooth Piggy-Back is a communication interface and is used to connect the inverter with other SMA Bluetooth-enabled devices. Only skilled workers may install and uninstall the Bluetooth Piggy-Back. The Bluetooth Piggy-Back may only be used with the following inverters:... -
Page 7: Standards
SMA Solar Technology AG 2 Safety Photovoltaic inverters Wind power inverters Sunny Boy (SB) Sunny Mini Central (SMC) Windy Boy (WB) SB 2800i SMC 6000TL WB 3000 SB 3000 SMC 6000TL‑IT WB 3000‑IT SB 3000‑IT SMC 7000TL WB 3300 SB 3000‑KR SMC 7000TL‑IT... -
Page 8: Safety Instructions
Technology to other SMA inverters and communication products with SMA Bluetooth (e.g., Sunny Explorer, Sunny Beam with Bluetooth). The Bluetooth Piggy‑Back reads inverter data and sends the data to a communication product with SMA Bluetooth Wireless Technology. You can read or configure the inverter data using the communication product. BTPB-Ant-IEN111510... -
Page 9: Scope Of Supply
Check the scope of supply for completeness and any visible external damage. Please contact your dealer if the scope of supply is not complete or you find any damage. Figure 1: Scope of delivery Item Quantity Description SMA Bluetooth Piggy-Back Plus: BTPB-G3 Installation guide Label with FCC certification, IC certification and CE mark Antenna Antenna cable... -
Page 10: Identifying The Bluetooth Piggy-Back
5 Identifying the Bluetooth Piggy-Back SMA Solar Technology AG Identifying the Bluetooth Piggy-Back Serial Number, Assembly Name, Production Version You can find the serial number, assembly name and production version of the Bluetooth Piggy-Back on the type label. The type label is located on the front of the Bluetooth Piggy-Back. -
Page 11: Preparing Bluetooth Communication
The NetID serves to distinguish PV plants with SMA Bluetooth in close proximity of each another. If another plant with SMA Bluetooth is located within 500 m of your plant, you will have to detect a free NetID. This way you will prevent setting a NetID for your plant that is already set for by another plant. - Page 12 • SMA Bluetooth Repeater • SMA Bluetooth Repeater Outdoor • SMA Power Injector with Bluetooth 2 to 9 and A to F Bluetooth is switched on. The device can connect with all SMA Bluetooth products with the same NetID. BTPB-Ant-IEN111510 Installation Guide...
-
Page 13: Mounting
SMA Solar Technology AG 7 Mounting Mounting 7.1 Installation Site Requirements • Keep a distance of at least 1 m from devices using the 2.4 GHz frequency band (e.g., WLAN devices, microwave ovens, devices with Bluetooth Wireless Technology). This will prevent reduced connection quality and data transmission speed. - Page 14 7 Mounting SMA Solar Technology AG Item Inverter From SB 1100 to SB 3000-KR as well as WB 1100 to WB 3000-IT, referred to as "Enclosure type A" in the following. From SB 3300 to SB 5000TL HC-IT as well as from WB 3300 to WB 3800-IT, referred to as "Enclosure type B"...
- Page 15 SMA Solar Technology AG 7 Mounting 4. Plug the Bluetooth Piggy-Back onto the interface socket, aligned to the left. Make sure to leave the two pins on the right side of the lower row of pins free. 5. Fasten the cable tie.
-
Page 16: Connecting The Antenna To The Bluetooth Piggy-Back
7 Mounting SMA Solar Technology AG 7.3 Connecting the Antenna to the Bluetooth Piggy-Back Requirement: ☐ You have installed the Bluetooth Piggy-Back in the inverter (see section 7.2). 1. For inverters with enclosure type A and enclosure type C: press the filler-plug in the middle out of the enclosure opening. - Page 17 SMA Solar Technology AG 7 Mounting 4. Attach the counter nut onto the antenna cable with the serrated edges facing towards the inverter enclosure. 5. First tighten the counter nut by hand, then screw it onto the antenna cable's thread with a torque of 9 Nm.
- Page 18 7 Mounting SMA Solar Technology AG • For inverters with enclosure type B: pass the antenna cable along the lower edge of the inverter enclosure. Pass the antenna cable towards the antenna connection of the Bluetooth Piggy-Back in a loop.
- Page 19 SMA Solar Technology AG 7 Mounting 10. Attach the label with the FCC and IC certifications and CE mark to the right side of the inverter enclosure, close to the type label. Installation Guide BTPB-Ant-IEN111510...
-
Page 20: Establishing Bluetooth Communication
Bluetooth Piggy-Back to the plant password using the Sunny Explorer software (see Sunny Explorer help). ☑ The Bluetooth Piggy-Back is establishing a connection to other devices with SMA Bluetooth. You can read or configure the inverter data using the communication product. -
Page 21: Updating The Firmware
SMA Solar Technology AG 9 Updating the Firmware Updating the Firmware You can update the firmware of the Bluetooth Piggy-Back using the Sunny Explorer software. The Bluetooth Piggy-Back remains in the inverter while the update is being performed. Requirement: ☐ The inverter's feed-in power is at least 50 W. -
Page 22: Decommissioning
10 Decommissioning SMA Solar Technology AG 10 Decommissioning 10.1 Removing the Bluetooth Piggy-Back Risk of lethal electric shock when opening the inverter. Death or serious injuries. • Disconnect the inverter on the AC and DC side (see inverter installation guide). Electrostatic discharge can damage the inverter. - Page 23 SMA Solar Technology AG 10 Decommissioning 6. Unscrew the antenna cable plug from the antenna connection of the Bluetooth Piggy-Back. 7. Pull the antenna cable out of the inverter through the enclosure opening. 8. Cut the cable tie and remove it from inverter.
-
Page 24: Disposing Of The Bluetooth Piggy-Back
• Observe the disposal regulations for electronic waste that apply at the installation site when disposing of the Bluetooth Piggy-Back. • In order to have us dispose of the Bluetooth Piggy-Back, send the Bluetooth Piggy-Back back to SMA Solar Technology AG at your own cost, labeled "ZUR ENTSORGUNG" ("FOR DISPOSAL"). BTPB-Ant-IEN111510... -
Page 25: Troubleshooting
SMA Solar Technology AG 11 Troubleshooting 11 Troubleshooting Problem Cause Measure The inverter with Bluetooth The inverter with Bluetooth • Commission the inverter with Bluetooth Piggy-Back (see Piggy-Back is not shown by Piggy-Back has not been the communication product. commissioned. - Page 26 Back and the communication communication product is product is too large. communication product. disturbed. • If required, use an SMA Bluetooth Repeater to cover the dead zones. The Bluetooth radio waves are • Position the communication being weakened by obstacles product in such a manner as to (e.g., walls, ceilings, doors).
-
Page 27: Technical Data
SMA Solar Technology AG 12 Technical Data 12 Technical Data 12.1 Bluetooth Piggy-Back Mechanical Data Width x length 50 mm x 81 mm Weight 60 g Communication Bluetooth Communication interface Maximum free-field communication range when 100 m installed, if inverter lid is closed and antenna is... -
Page 28: Antenna
12 Technical Data SMA Solar Technology AG 12.2 Antenna Mechanical Data Diameter x length 10 mm x 130 mm Weight 12 g Ambient Conditions Ambient temperature − 40 °C … +85 °C Relative humidity 5 % … 95 % Maximum height... -
Page 29: Contact
SMA Solar Technology AG 13 Contact 13 Contact If you have technical problems concerning our products, contact the SMA Serviceline. We require the following information in order to provide you with the necessary assistance: • type and serial number of the inverter •... - Page 31 The use of supplied software produced by SMA Solar Technology AG is subject to the following conditions: • SMA Solar Technology AG rejects any liability for direct or indirect damages arising from the use of software developed by SMA Solar Technology AG. This also applies to the provision or non-provision of support activities.