LCN 2210DPS Series Installation Instructions

*18363*
18363
TM
Door Closers
1a Make sure hand of closer matches hand of door.
Remove finish plates. Hand of closer is printed on
the mounting plate label. Hand of closer cannot be
Fig. 1
reversed. See diagram above to determine hand of
door.
1b Prepare and mortise door & frame per template on pg.
4.
1c For 2210DPS: connect wire leads to monitor device as
shown in Fig. 2. Do not pinch wires when installing
closer into headframe. (Switch contact information
with door closed and switch closed.)
1d Install closer in prepared headframe, as shown in Fig.
1, with spring tube pointing away from hinge. Fasten
mounting plate to jamb with Z\v-20 x B\, PHMS provided.
Finish Plate
1e Torx Screws Install track in door. Roller access hole must be toward
latch edge of door, as shown in Fig. 1. Fasten with Z\v- Arm Shaft
Screw
20 x Z\x TORX MS provided.
Track
Torx
1f Connect arm assembly to track by placing plastic roller
Screws
at end of arm into the roller access hole in track. See
Fig. 1. Let arm assembly rest on top of installed track.
Track
Fig. 3
1g

To attach arm to closer:

1. Open door out of working area.
2. With a " hex wrench, turn latch & main speed regulating
C\cx
screws all the way in (clockwise). See Fig. 3. DO NOT FORCE
Latch
Speed
SCREWS.
3. Using an adjustable wrench, rotate door closer shaft
Closer
Assembly
approximately 90°. See Fig. 4. (R.H. - clockwise/L.H. -
counterclockwise).
Mounting
Screws
Fig. 2
To Monitor
Fig. 4 Finish
Device
Plate
Arm
Assembly
From
Roller
2210dps
Access
Hole
Standard door position switch supplied has
contacts rated at 0.1 amp 125/250 VAC MAX
Fig. 3
Latch
Speed

How To Tell Hand Of Door

Left
Hand
Door
Fig. 4
To Monitor
Device
2210DPS Series
Closer
Assembly
Mounting
Screws
Finish
Plate
Arm
Assembly
Roller
Access
Hole
Back
Main
Check
Speed
90°
Black (COM)
Blue (N.C.)
Red (N.O.)
(Switch contact information
with door closed.)
Back
Main
Check
Speed
Right
Hand
Door
90°
TM
TM
Fig. 1
Fig. 1
Finish Plate
Torx Screws
Arm Shaft
Screw
Track
Torx
Screws
Track
Finish Plate
Torx Screws
Fig. 3
Arm Shaft
Screw
Track
Torx
Screws
Latch Main
Fig. 2
Speed Speed
Track
From
2210dps
Fig. 4
Fig. 2
To Monitor
Device
From
2210dps
Standard door position switch supplied has
contacts rated at 0.1 amp 125/250 VAC MAX
CAUTION
Improper installation or regulation may result in personal
injury or property damage. Follow all instructions
carefully. For questions contact LCN Closers:
877-671-7011
Customer Service
1-877-671-7011
How To Tell Hand Of Door
Left
Hand
Door
Fig. 3
Installation Instructions
Latch Main
Speed Speed
Closer
Assembly
Mounting
Screws
Closer
Finish
Fig. 4
Assembly
Plate
Arm
Mounting
Assembly
Screws
Roller
Access
Finish Hole
Plate
Arm
Assembly
Roller
Access
Hole
Back
To Monitor
Check
Device
Black (COM)
Blue (N.C.)
Red (N.O.)
(Switch contact information
How To Tell Hand Of Do
with door closed.)
Left
Standard door position switch supplied has
contacts rated at 0.1 amp 125/250 VAC MAX
Hand
Door
90°
Black (COM)
Blue (N.C.)
Red (N.O.)
(Switch contact information
with door closed.)
www.allegion.com/us
Right
Hand
Door
© Allegion 2018
Printed in U.S.A.
18363 Rev. 02/18-h
Back
Che
90°
Ri
Ha
Do