Galaxy Audio LA4D Quick Start Manual

GAL A X Y AUDIO
Included Components
1.
LA4D x1
2. IEC Power Cable x1
3.
Quick Start Guide x1
Setup
1
Connect power cable to LA4D, connect
other end to a power outlet.
6
For a stereo signal from an MP3 player,
attach 1/8" stereo cable into the 1/8"
input, this input will sum left and right.
2
Level control: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
1.
2
Choose the input needed:
XLR for microphone or line level.
1/4" for balanced/unbalanced line level.
1/8" for stereo from a media player etc.
Stand Mounting
1
With a firm grip, align the LA4D up with
the speaker stand.
3
Tone controls: To increase the low
frequencies, turn the "Low" tone control
clockwise. To decrease, turn
counter-clockwise.
2.
3
For a microphone, plug the XLR male
end of the cable into the XLR female
connector on the LA4D. If the
microphone is a condenser that requires
phantom, turn on phantom power switch.
2
Carefully bring the LA4D down onto the
speaker stand.
4
Tone controls: To increase the high
frequencies, turn the "high" tone control
clockwise. To decrease, turn
counter-clockwise.
3.
GAL A X Y AUDIO
Q uick Start Guide
Included Components
1. 1. 2. 3.
LA4D x1
2. IEC Power Cable x1
3. Quick Start Guide x1
Setup
1 2 3 4 5
Connect power cable to LA4D, connect Choose the input needed: For a microphone, plug the XLR male For line level with an XLR cable, move For line level with a 1/4" cable, plug into
other end to a power outlet. XLR for microphone or line level. end of the cable into the XLR female the 0,20dB switch to the 20dB PAD the 1/4" input that is to the left of the
1/4" for balanced/unbalanced line level. connector on the LA4D. If the position. Plug the XLR male end of the XLR. This can be a balanced TRS or an
1/8" for stereo from a media player etc. microphone is a condenser that requires cable into the XLR female connector on unbalanced TS input.
phantom, turn on phantom power switch. the LA4D.
Stand Mounting Operation
6 1 2 3 1
For a stereo signal from an MP3 player, With a firm grip, align the LA4D up with Carefully bring the LA4D down onto the Insure the input level control is turned
attach 1/8" stereo cable into the 1/8" the speaker stand. speaker stand. down (fully counter-clockwise) Turn the
input, this input will sum left and right. power switch on.
2 3 4 5
Level control: turn clockwise to raise the Tone controls: To increase the low Tone controls: To increase the high Max. level is reached when the yellow
level. Turn counter-clockwise to lower frequencies, turn the "Low" tone control frequencies, turn the "high" tone control "Comp" light only flashes at peak levels.
the level. clockwise. To decrease, turn clockwise. To decrease, turn If the light is on constantly, turn the level
counter-clockwise. counter-clockwise. control down to avoid damage to the
LA4D.
4
For line level with an XLR cable, move
the 0,20dB switch to the 20dB PAD
position. Plug the XLR male end of the
cable into the XLR female connector on
the LA4D.
3
5
Max. level is reached when the yellow
"Comp" light only flashes at peak levels.
If the light is on constantly, turn the level
control down to avoid damage to the
LA4D.
Quick Start Guide
5
For line level with a 1/4" cable, plug into
the 1/4" input that is to the left of the
XLR. This can be a balanced TRS or an
unbalanced TS input.
Operation
1
Insure the input level control is turned
down (fully counter-clockwise) Turn the
power switch on.