Galaxy Audio PA6BT Quick Start Manual

GAL A X Y AUDIO
Full Range Powered Personal Monitor
Included Components
1.
PA6BT x1
2.
IEC Power Cable x1
3.
MSA-1 Stand Adapter x1
4.
Quick Start Guide x1
Setup
1
Connect power cable to PA6BT, connect
other end to a power outlet.
6
For a stereo signal from an MP3 player,
attach 1/8" stereo cable into the Channel
2 1/8" input.
2
Flip the power switch on.
1.
2
Choose the input needed and for what
channel(s) needed:
XLR/1/4" Combo Jack for mic, or
balanced/unbalanced line level.
1/8" for stereo from a media player etc.
7
The Pre Out provides a Line Level mix
of all three channels.
3
Level controls: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
2. 3.
3
For a balanced mic signal, plug the XLR
male end of the cable into the XLR/1/4"
Combo Input on the PA6BT. For strong
signals, engage the -20dB Pad Switch to
prevent distortion.
Stand Mounting
(Optional)
1
Attach the MSA-1 to the mic stand, then
Lift the PA6BT over the stand, align it up
with the hole.
4
Using Bluetooth - Press the Bluetooth
® ®
button. The Bluetooth LED will flash for
®
15 seconds. Locate the PA6BT on your
device and select to pair. If pairing fails,
turn Bluetooth off and try again. The
®
button also acts as a Stop/Play/Pause.
Powering the unit off will disconnect.
4.
GAL A X Y AUDIO
Q uick Start Guide
PA6BT
Full Range Powered Personal Monitor
Included Components
1. 1. 2. 3. 4.
PA6BT x1
2. IEC Power Cable x1
3. MSA-1 Stand Adapter x1
4. Quick Start Guide x1
Setup
1 2 3 4 5
Connect power cable to PA6BT, connect Choose the input needed and for what For a balanced mic signal, plug the XLR For Balanced or Unbalanced Line Level, Connect a female XLR to the Thru
other end to a power outlet. channel(s) needed: male end of the cable into the XLR/1/4" plug the 1/4" cable into the XLR/1/4" output to feed the channel's XLR input
XLR/1/4" Combo Jack for mic, or Combo Input on the PA6BT. For strong Combo Jack on the PA6BT. to another device.
balanced/unbalanced line level. signals, engage the -20dB Pad Switch to
1/8" for stereo from a media player etc. prevent distortion.
Stand Mounting (Optional) Operation
6 7 1 2 1
For a stereo signal from an MP3 player, The Pre Out provides a Line Level mix Attach the MSA-1 to the mic stand, then Bring the PA6BT down onto the stand Ensure that both channels and/or the
attach 1/8" stereo cable into the Channel of all three channels. Lift the PA6BT over the stand, align it up gently until secure. Bluetooth controls have their levels
2 1/8" input. with the hole. lowered by turning counter-clockwise. ®
2 3 4 5 6
Flip the power switch on. Level controls: turn clockwise to raise the Using Bluetooth - Press the Bluetooth ® ® EQ controls - Low/Mid/Hi: To increase the Reduce Input Levels if the Clip LED turns
level. Turn counter-clockwise to lower button. The Bluetooth LED will flash for ® low, mid, and high frequencies, turn the on. Max. level is reached when the yellow
the level. 15 seconds. Locate the PA6BT on your appropriate tone control clockwise. To "Comp" light flashes at peak levels. If the
device and select to pair. If pairing fails, decrease, turn counter-clockwise. light is on constantly, turn the levels down
turn Bluetooth off and try again. The ® to avoid damage to
button also acts as a Stop/Play/Pause. the PA6BT.
Powering the unit off will disconnect.
4
For Balanced or Unbalanced Line Level,
plug the 1/4" cable into the XLR/1/4"
Combo Jack on the PA6BT.
2
Bring the PA6BT down onto the stand
gently until secure.
5
EQ controls - Low/Mid/Hi: To increase the
low, mid, and high frequencies, turn the
appropriate tone control clockwise. To
decrease, turn counter-clockwise.
Quick Start Guide
PA6BT
5
Connect a female XLR to the Thru
output to feed the channel's XLR input
to another device.
Operation
1
Ensure that both channels and/or the
Bluetooth controls have their levels
®
lowered by turning counter-clockwise.
6
Reduce Input Levels if the Clip LED turns
on. Max. level is reached when the yellow
"Comp" light flashes at peak levels. If the
light is on constantly, turn the levels down
to avoid damage to
the PA6BT.