Orion GST-795h Quick Manual

2 MEGA PIXEL
NETWORK VANDAL-PROOF
DOME CAMERA
GST-795h
QUICK GUIDE
pter 1. Install and Specification
afety Cautions
This camera may be damaged by electrical and physical shock.
Use regulated 12V DC, 1A power supply. Do not throw or drop it onto floor.
In case it is installed at high location, be sure to mount securely to prevent the
unit from falling below.
n case the unit fails, Do not try to disassemble the product.
Contact or consult the distributor or an authorized technician for after-sales
service.
Warranty void for the product disassembled without an authorization from the
distributor or an authorized technician.
All responsibility by using this unit is on the user.
This product has 2 models according to IR LED.
① SK-NV30(w/o IR)
② SK-NV30IR(with IR)
This manual is based on SK-NV30IR.
If the product is to be put out of operation definitively, take it to a
local recycling plant for a disposal which is not harmful to the
environment.
ackage
Camera Quick Guide
Software & User Manual CD Screw 4x25 Tp1 3EA

1.4 Specification

1.4.1 Camera Specification

Item Specification
Item
Specification
Model No. GST-795h
G4S-795
Model No.
Type 2MP network vandal-proof dome camera
Image Sensor 1/2.8" SONY IMX291 STARVIS
Megapixel network vandal-proof dome camera
T ype
Number of effective pixels 1945(H)×1097(V) approx
2 1/2.8" SONY PROGRESSIVE SCAN EXMOR CMOS
Image Sensor
Stream Multiple Stream
Main Stream 1
Effective Pixels 1984(H) x 1225(V)
1920×1080,1280x1024 ,1280x960,1280x720
Sub-stream2
1920x1080 / 1280x1024 /
Resolution 1280x720,800x600,704x576,640×360,
Network Specification 1280x960 / 1280x720 / 1024x768 / 640x480 / 320x240
Resolution
640x480,352x288,352x288,
320x288,320x176
Classification Item Specification
Scanning System Progressive Scan
Sub-stream 3
704x576,640x480,640×360,352x288,320x288,320x176
OS
Embedded Linux LED OFF : 0.01Lux
H.264 Baseline/H.264 Main Profile/H.264 High Profile /
Min.Illumination
Encode Type
Network Interface RJ45 10/100BaseT, Ethernet
H.265 Main Profile LED ON : 0Lux(25M Range)
IR LED OFF:0.01Lux
Setting
By web browser
Min.llumination
IR LED 24PCS
IR LED ON: 0Lux(25M Rang)
IR LED 24PCS
Leased Line, Cable Modem, Support Dynamic
Lens Vari-focal auto iris megapixel lens
Network Support
IP and Static IP, ADSL usable under Router
Alarm Input/Output Input :1,Output:1
Summary
Lens Vari-focal iris megapixel lens
TCP/IP, UDP/IP, RTP, RTSP, RTCP, NTP,
Supported Protocol
1.4.2 Image Function
HTTP, DHCP, FTP, SMTP, DNS, DDNS

1.4.2 Camera Function

Image
Security User authentication
Specifications
Item
Rotate mode, saturation, brightness, contrast,
PC OS Image settings
WINDOWS XP, WINDOWS VISTA, WINDOWS 7
adjustable through
Privacy Zone
ON / OFF(6 Programmable Zones)
Day&Night Auto/Day/Night
Web Browser IE 7.0 or higher
Day&Night Auto / Night / Day
WDR WDR(Disable,Low,High)
Compression H.264, MPEG-4, MJPEG
Electronic Shutter 1/5s to 1/50,000s
WDR WDR(1 ~ 5), (Back Light, Front Light)
Privacy Mask On/Off( 4 Programmable Zones)
Function 1920x1080 /
Auto : 1/25 ~ 1/5,000(NTSC), 1/12.5 ~ 1/8,000(PAL)
Electronic Shutter 1280x1024 / 1280x960 / 1280x720 /
Resolution White Balance Auto,Cloudy,Sunny,Fluorescent,Tungsten
Suppress Rolling, Manual
1024x768 / 640x480 / 320x240
Image
ROI Up to 4 configurable areas.
Sense Up
Auto(1 ~ 14)
200 : 1(Typical)
Compression Rate
White Balance
Auto / Indoor / Outdoor / Fluorescent / User
Frame Rate Max. 30fps(@1920X1080)
64 ~ 9000kbps
Bit Rate 5
Simultaneous Access
Max. 10 users
Video Recording Recording in client PC with CMS or FTP Server

Chapter 1. Install and Specification

1.1 Safety Cautions

1) This camera may be damaged by electrical and physical shock.
Use regulated 12V DC, 1A power supply. Do not throw or drop it onto floor.
2) In case it is installed at high location, be sure to mount securely to prevent the
unit from falling below.
3) In case the unit fails, Do not try to disassemble the product.
Contact or consult the distributor or an authorized technician for after-sales

1.3 How to Install

service.

1.3.1 Camera installation

Warranty void for the product disassembled without an authorization from the
distributor or an authorized technician.
Fix the camera set with the supplied screws on ceiling or wall mount. If you
4) All responsibility by using this unit is on the user.
don't use supplied screws, the camera may fall off.
5) This product has 2 models according to IR LED.
Put a sticker on the ceiling and make holes according to the spots marked on
① SK-NV30(w/o IR)
a sticker.
If the product is to be put out of operation definitively, take it to a local
② SK-NV30IR(with IR)
recycling plant for a disposal which is not harmful to the environment.
※This manual is based on SK-NV30IR.
<Ceiling mount>
If the product is to be put out of operation definitively, take it to a
local recycling plant for a disposal which is not harmful to the
1.2 Packge
environment.
2MEGA PIXEL
NETWORK VANDAL-PROOF
1.2 Package DOME CAMERA
GST-795h
QUICK GUIDE
Camera Quick Guide
Camera Quick Guide Software&User Manual CD
Software & User Manual CD Screw 4x25 Tp1 3EA
<Wall mount> Screw 4x25 Wrench A Sealed
Tp1 3EA silica gel
2

1.4.3 Network Specification

1.4.3 Interface
Classification Item Specification
Interface
OS
Embedded Linux
Audio input 1-ch RCA audio interface
Network Interface
RJ45 10/100BaseT, Ethernet
Audio output 1-ch RCA audio interface
Communication interface Setting RJ45 10M / 100M ethernet port By web browser
Alarm I/O Alarm input :1,Alrm output:1
Leased Line, Cable Modem, Support Dynamic
3
Network Support
Video output 1 Vp-p composite output (75 Ω / BNC) IP and Static IP, ADSL usable under Router
Summary
TCP/IP, UDP/IP, RTP, RTSP, RTCP, NTP,
Supported Protocol
HTTP, DHCP, FTP, SMTP, DNS, DDNS

1.4.4 Electric Specification

1.4.4 Electric Specification
Security User authentication
Classification PC OS WINDOWS XP, WINDOWS VISTA, WINDOWS 7 Specification
Web Browser IE 7.0 or higher
Regulated 12V DC, PoE(Power over Ethernet) - IEEE802.3af
Power Supply
Compression H.264, MPEG-4, MJPEG
Current Consumption Max. 1A(DC 12V) IR LED ON
1920x1080 /
Operation T emp. -45~50℃
1280x1024 / 1280x960 / 1280x720 /
Resolution
1024x768 / 640x480 / 320x240
Dimension Ø150.5 x 95.6(H)mm
Image
Weight Compression Rate Approx. 400g Approx. 750g 200 : 1(Typical)
Frame Rate Max. 30fps(@1920X1080)
64 ~ 9000kbps
Bit Rate
Simultaneous Access Max. 10 users
Video Recording
Recording in client PC with CMS or FTP Server
Motion Detection Support
Privacy Zone Support
Function OSD Support
Support
Dynamic IP
IP Router Support
Support
DDNS
6
1.3 How to Install
1.3.1 Camera installation
1.3 How to Install
1. Camera installation
Fix the camera set with the supplied screws on ceiling or wall mount. If you
(1) F ix the camera set with the supplied screws on ceiling or wall mount. If you don't use supplied screws, the camera may fall off.
don't use supplied screws, the camera may fall off.
Put a sticker on the ceiling and make holes according to the spots marked on
(2) P ut a sticker on the celling and make holes according to the spots marked on
a sticker.
a sticker.
<Ceiling mount>

1.3.2 Camera Angle Adjustment

1) Pan adjustment : Grasp the disk of camera and then adjust direction to the <Ceiling mount>
right or left(-160 ~ 190 ) ° °
2) Tilt adjustment : Grasp the LED cover of camera and then adjust direction to
MOUNT HOLE PLATE(STICKER)
the up or down(6 ~ 90 ) ° °
Put a sticker on the ceiling and make holes
3) Roll adjustment : Grasp the camera holder and then rotate(-178 ~ 178 )
according to the spots marked on a sticker
<Caution> If you try to adjust the camera out of limited angle, it might cause troubles
MOUNT HOLE PLATE(STICKER)
MOUNT HOLE PLATE(STICKER)
and damage to camera.
Put a sticker on the ceiling and make holes SCREW Tp1 4X25 3EA
according to the spots marked on a sticker
Put a sticker on the ceiling and make holes
MOUNT HOLE PLATE(STICKER)
according to the spots marked on a sticker
Put a sticker on the ceiling and make holes
SCREW Tp1 4X25 3EA
according to the spots marked on a sticker
SCREW Tp1 4X25 3EA
SCREW Tp1 4X25 3EA
<Wall mount>
<Wall mount>
MOUNT HOLE PLATE(STICKER)
MOUNT HOLE PLATE(STICKER)
Put a sticker on the wall and make holes
Put a sticker on the wall and make holes
according to the spots marked on a sticker
according to the spots marked on a sticker
MOUNT HOLE PLATE(STICKER)
Put a sticker on the wall and make holes
according to the spots marked on a sticker
MOUNT HOLE PLATE(STICKER)

1.3.3 Lens Adjustment

Put a sticker on the wall and make holes
according to the spots marked on a sticker
After opening the LED cover, SCREW Tp1 4X25 3EA
1) ① By turning the "Tele-Wide" knob, you can
SCREW Tp1 4X25 3EA
SCREW Tp1 4X25 3EA
Access a range of focal lengths within specified limits.
Mount hole
2) ② Since then, by turning the "Near-Far" knob,
plate(sticker)
you can set the focus toward the wanted object.
SCREW Tp1 4X25 3EA
1.3.4 Dimension
3
1.4.4 Electric Specification

1.4.5 Alarm input/Output

Classification
Power Supply Regulated 12V DC, PoE(Power over Ethernet) - IEEE802.3af
Current Consumption
Max. 1A(DC 12V) IR LED ON
Operation T emp. -45~50℃
Dimension Ø150.5 x 95.6(H)mm
Weight Approx. 400g
1.4.7 Basic Setting T able
Item Default(Basic setting)
Network
Static IP/Dynamic IP Static IP
IP Server Enable Enable
1.4.6 Audio input/Output
IP Address 192.168.1.30
Gateway 192.168.1.1
Subnet Mask 255.255.255.0
Web Connection
80
Port
RTSP Port 554
RTP Port Range 5000 ~ 5999
ID and Password
Administrator
admin/admin
ID/Password
User ID/Password root/root, guest/guest
Domain of Related Server
DDNS Server iplinker.net
7
Stream setting
1.3.2 Camera Angle Adjustment
1) Pan adjustment : Grasp the disk of camera and then adjust direction to the
1.3.2. Camera angle adjustment :
right or left(-160 ~ 190 )
(1) P an adjustment : Grasp the
2) Tilt adjustment : Grasp the LED cover of camera and then adjust direction to
disk of camera and then adjust
the up or down(6 ~ 90 )
direction to the right or left(-
3) Roll adjustment : Grasp the camera holder and then rotate(-178 ~ 178 )
160°~190°)
(2) T ilt adjustment : Grasp the <Caution> If you try to adjust the camera out of limited angle, it might cause troubles
Ø3.5 Ø30 LED cover of camera and then and damage to camera.
adjust direction to the up or
down(6°~90°)
(3) R oll adjustment : Grasp the
Ø3.5 Ø30
Ø3.5 Ø30
camera holder and then rotate
(-178°~178°)
Ø3.5 Ø30 <Caution> I f you try to adjust the camera out of limited angle, it might cause
° °
troubles and damage to camera.
1.3.3 Lens Adjustment
After opening the LED cover,
① B y turning the "Tele-Wide" knob, you can access a
range of focal lengths within specified limits.
② S ince then, by turning the "Near-Far" knob, you can
set the focus toward the wanted object.
1.3.3 Lens Adjustment
After opening the LED cover,
1.3.4 Sllica gel
1) ① By turning the "Tele-Wide" knob, you can
W hen installed in high humidity area, take out silica gel
Access a range of focal lengths within specified limits.
from polythene bag then put silica gel into the dome
2) ② Since then, by turning the "Near-Far" knob,
camera.
you can set the focus toward the wanted object.
Ø30 Ø30
*Must use silica gel from sealed polythene bag.
Ø3.5 Ø3.5
1.3.4 Dimension
Ø30 1.3.5 Dimension
Ø3.5
Ø30
Ø100
Ø3.5
Ø150.5
1.4.7 Basic Setting T able
1.4.7 Basic setting Table.
Specification Item
Item Default setting
Network
Static IP/Dynamic IP
Network
IP Server Enable
Static IP/
Static IP
4
DHCP
IP Address
IP address
192.168.1.30
Gateway
Subnet Mask
Subnet mask 255.255.255.0
Web Connection
Port
Remarks Gateway
192.168.1.1
RTSP Port
Web Port 80
RTP Port Range
ID and Password
RTSP port
554
Administrator
ID/Password
Upnp Disable
User ID/Password
Date&Time GMT+01:00
Domain of Related Server
DDNS Server
Resolution 1920x1080,640x360
Stream setting
MIC(Red)
ID/Password admin/admin
Stream 1
Stream setting
Stream 2
Stream 3
LINE OUT(Black)
Stream1 H.264 1920x1080,25fps
Video out*
Stream2
H.264 640x360,25fps
[Reference] In case to reset hardware and network setting, ID and password of user
and Administrator will be automatically returned to the above default value.
Stream3 H.264 ,352x288,25fps
*Frame rate can be affected by the external video output option.
So factory default is off. When you install the camera, enable this option. Then
disable it after the installation.
rtsp://<ip address>:554/stream1
° ° LED COVER
DISK
R
L
° °
° °
U
CAMERA HOLDER
ROTATION
D
LED COVER
DISK
R
L
U
CAMERA HOLDER
ROTATION
D
1
w
2
N
T
F
Ø100
Ø150.5 Ø129
Ø129
4
Default(Basic setting) Remarks
Remarks
Static IP
Enable
192.168.1.30
192.168.1.1
255.255.255.0
80
554
5000 ~ 5999
admin/admin
root/root, guest/guest
iplinker.net Main stream:1920x1080,25fps,
Sub stream: 640x360,25fps
H.264 30fps@(1920x1080) rtsp://<ip address>:554/stream1
rtsp://<ip address>:554/stream2
None
rtsp://<ip address>:554/stream3
None
rtsp://[ip address]:554/media/live/1/1
After installation, deactivate it.
OFF
rtsp://[ip address]:554/media/live/1/2
rtsp://[ip address]:554/media/live/1/3
8