General Safety Summary General Safety Summary Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it. To avoid potential hazards, use this product only as specified. Only qualified personnel should perform service procedures. To Avoid Fire or Personal Use proper power cord.
Page 9
General Safety Summary Terms in This Manual These terms may appear in this manual: WARNING. Warning statements identify conditions or practices that could result in injury or loss of life. CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.
Service Safety Summary Service Safety Summary Only qualified personnel should perform service procedures. Read this Service Safety Summary and the General Safety Summary before performing any service procedures. Do Not Service Alone. Do not perform internal service or adjustments of this product unless another person capable of rendering first aid and resuscitation is present.
Kit description Kit description This document provides instructions for performing hardware and/or software and option key upgrades on the following Tektronix products: MTS4000 MPEG Test System MTS4SA MPEG Test System Upgrade kits covered by MTS4KUP GEN – Multiplexer, MPEG Player, Transport Stream Editor, Make Seamless Wizard, Transport Stream Cutter, and Script Pad.
Page 12
Kit description viii MTS4000 Upgrade Kit Instructions...
Description MTS4000 OPTION KEY LABEL 020-2965-xx TCLIPS MPEG TEST STREAMS DVD PACKAGE 075-1036-xx MTS4KUP UPGRADE KIT INSTRUCTIONS 071-2179-xx MANUAL, TECH; SMPLP; TEKTRONIX SUPPLEMENTAL INFORMATION SHEET FOR THE PEOPLES REPUBLIC OF CHINA; CHINA ROHS MTS4KUP ESS Quantity Part Number Description MTS4000 OPTION KEY LABEL...
Page 14
Description PQA600 OPTION KEY LABEL 020-3054-xx PQA600 APPLICATION SOFTWARE KIT 075-1036-xx MTS4KUP UPGRADE KIT INSTRUCTIONS 071-2179-xx MANUAL, TECH; SMPLP; TEKTRONIX SUPPLEMENTAL INFORMATION SHEET FOR THE PEOPLES REPUBLIC OF CHINA; CHINA ROHS MTS4KUP PB Quantity Part Number Description MTS4000 OPTION KEY LABEL...
Page 15
CABLE ASSY; RF, BNC TO BNC;75 OHM 348-2003-00 BUMPER, RUBBER; CLEAR, 0.375 DIA X 0.200 H 075-1036-xx MTS4KUP UPGRADE KIT INSTRUCTIONS 071-2179-xx MANUAL, TECH; SMPLP; TEKTRONIX SUPPLEMENTAL INFORMATION SHEET FOR THE PEOPLES REPUBLIC OF CHINA; CHINA ROHS MTS4KUP QB2 Quantity Part Number...
Page 16
Part Number Description 131-7834-00 OPTICAL GIGABIT ETHERNET/FIBRE CHANNEL 850NM SFP, 1.25/1.0625GBAUD, 3.3V 075-1036-xx MTS4KUP UPGRADE KIT INSTRUCTIONS 071-2179-xx MANUAL, TECH; SMPLP; TEKTRONIX SUPPLEMENTAL INFORMATION SHEET FOR THE PEOPLES REPUBLIC OF CHINA; CHINA ROHS MTS4KUP LX Quantity Part Number Description 131-7957-00 OPTICAL GIGABIT ETHERNET/FIBRE CHANNEL 1310NM SFP SFF, 1.25/1.0625GBAUD, 3.3V...
3. Start the MTS4000 Option Key Wizard. Select Start > Programs > Tektronix MTS4000 > OptionKey Wizard. 4. In the Tektronix Option Update dialog box, enter the Option Key String supplied with the installation documentation in the Key String field.
Page 18
Software upgrade instructions 7. ESE or ESS Options only: a. Insert the CD, provided in the kit, into the CD/DVD drive. b. Navigate to the CD and display its contents. Double click the remoteupdate.exe file to update the dongle. c. Follow any on-screen instructions. d.
MTS4KUP QB2 MTS4KUP VS These instructions are for personnel who are familiar with servicing the product. Contact your nearest Tektronix, Inc., Service Center or Tektronix Factory Service for installation assistance. NOTE. Up to four optional interface cards can be installed into the instrument, but only two of the following options: S2, VS, QB2, IPTV.
Hardware upgrade instructions Prepare IPTV, QB2, S2, and Some interface cards require the application of a rubber bumper to the interface card before installing into the instrument. Refer to the following illustrations for VS interface cards the proper locations to install the bumper. Figure 1: IPTV interface card bumper installation Figure 2: QB2, S2, and VS interface cards bumper installation MTS4000 Upgrade Kit Instructions...
Page 21
Hardware upgrade instructions Install the interface card Before installing any of the interface cards, refer to the following table and illustration to determine which slots in the instrument you’ll be installing your interface card or cards. Due to their size, some interface cards require two slots. Table 2: Interface card slot locations Interface Slot...
Hardware upgrade instructions 3. Close front of the instrument and place the cabinet on the working surface with the rear panel facing up. 4. Unscrew the eight screws securing the rear panel. (The screws do not come out of the panel.) Figure 3: Remove rear panel 5.
Page 23
Hardware upgrade instructions 6. Remove the six screws from the interface card support bracket and lift it from the cabinet. 7. Depending on the option card being installed, remove the appropriate blank panel from the rear of the instrument. Use the table to identify the recommended location for each of the available interface card.
Hardware upgrade instructions 9. Use the screw(s) from the removed blank panel(s) and attach the interface card to the chassis. NOTE. Some interface cards require the removal of two blank panels. 10. ASI Option only: a. Install two BNC washers and a nut to each of the four BNC connectors. Torque the BNC nuts to 14 in/lb.
Hardware upgrade instructions 12. QB2, S2, and VS Options only: a. Install the CIP cable from J14 on the interface card to a COM connector on the motherboard. Refer to the Interface card slot locations table at the beginning of this procedure to identify the proper placement of the interface card and proper COM connector.
Page 27
Hardware upgrade instructions CAUTION. Before reinstalling the interface card support bracket in the next step, check that none of the card stabilizers are already in their lowered position. 13. Reinstall the interface card support bracket. 14. Some option cards are longer then others. If the option card being installed reaches the adjustable card stabilizers on the interface card support bracket, then you need to support the circuit board.
Page 28
Hardware upgrade instructions 15. Connect the power cable to the rear panel fan (if it was disconnected) and install the rear panel. MTS4000 Upgrade Kit Instructions...
Optical SFP upgrades Optical SFP upgrades The Optical SFP upgrade kits simply contain the new optical SFP module, to be used with the Option IPTV interface card. There are no installation requirements other than installing the SFP module into the Option IPTV interface card when required. The Optical SFP upgrade kits are: MTS4KUP SX MTS4KUP LX...
Need help?
Do you have a question about the MTS4000 MPEG and is the answer not in the manual?
Questions and answers