REMS Curvo Instruction Manual
Hide thumbs
Also See for Curvo:
- Instruction manual (145 pages) ,
- Instruction manual (93 pages) ,
- Instruction manual (97 pages)
Subscribe to Our Youtube Channel
Related Manuals for REMS Curvo
Summary of Contents for REMS Curvo
-
Page 1: Instruction Manual
P r o f e s s i o n a l s Instruction Manual REMS Curvo REMS Curvo 50 REMS Akku-Curvo REMS Sinus... - Page 2 REMS Curvo / REMS Curvo 50 REMS Curvo / REMS Curvo 50 REMS Curvo REMS Curvo R 88 R114 R140 Fig. 1a R102 R40– R77 1 1 3 REMS Curvo 50 REMS Curvo 50 Fig. 1b...
- Page 3 REMS Akku-Curvo REMS Akku-Curvo REMS Akku-Curvo REMS Akku-Curvo R 88 R114 R140 R102 R40– R77 Fig. 1c...
- Page 4 REMS Curvo / REMS Curvo 50 / REMS Akku-Curvo / REMS Sinus Fig. 2 REMS Sinus REMS Curvo REMS Akku-Curvo REMS Curvo 50 Biegesegment und Gleitstück für Rohre Ø mm/Zoll 90° 45° Art.-Nr. 581400 ...
-
Page 5: General Safety Instructions
Danger of injury. connecting to power source and/or battery pack, picking up or carrying the ● Be careful when bending with REMS pipe bending machines. These develop tool. Carrying power tools with your fi nger on the switch or energising power a high bending force. -
Page 6: Safety Instructions For Batteries
Save all warnings and instructions for future reference. support 35 – 50, insert bolt, instruction manual, transport crate. ● Only use the battery in REMS power tools. Only then is the battery safe from REMS Akku-Curvo: Cordless pipe bending machine, Li-Ion battery, rapid dangerous overloading. -
Page 7: Preparations For Use
The indicated weighted effective value of acceleration has been measured In REMS Curvo 50 the support 35 – 50 (11) or support 10 – 40 (13) respec- against standard test procedures and can be used by way of comparison with tively should be attached above the back formers and bending formers another device. -
Page 8: Maintenance
REMS Akku-Curvo is equipped with low discharge protection for the battery. In REMS Curvo 50 the support 35 – 50 (11) or support 10 – 40 (13) respec- This switches off the power tool as soon as the battery needs to be recharged. -
Page 9: Manufacturer's Warranty
REMS is not responsible, shall be excluded from the warranty Services under the warranty may only be provided by customer service stations authorized for this purpose by REMS. - Page 10 Use for the intended purpose WARNING REMS Sinus is intended for cold draw bending of pipes up to 180°. All other uses are not for the intended purpose and are therefore prohibited. Scope of Supply Manual pipe bending machine, insert bolt, bending formers and back formers according to ordered set, REMS bending spray, instruction manual, steel case.
- Page 11 REMS Sinus Operation with vice Securely clamp bender drive in vice and move spindle in starting position. Put lever with square seat into the spindle in a proper position. Insert selected bending former into the spindle. Turn lever anticlockwise until the required bending angle has been reached.
- Page 12 REMS Sinus Operation as 2-hand-bender: Screw additional lever into the bender drive, then continue as described in fi g. 2 – 5.
Need help?
Do you have a question about the Curvo and is the answer not in the manual?
Questions and answers