Page 1
WaterRower M1 unit is kept in good condition and functioning at all times. STORAGE The WaterRower can be stored upright. To do so, lift the end of the rower and move the WaterRower on the front wheels to the area of storage.
Table of Contents MAINTENANCE PAGE Daily Maintenance..........4 Weekly Dust Build Up........... 4 Loose Bolts............4 Alignment of the Belts........4 Quarterly Clean Seat Wheels.......... 5 Check Tension of Recoil........5 Every 6 Months Water Condition..........5 Tank Stopper in Place........5 Every 1-2 Years Replace Batteries..........
Wipe down handle, seat, rails and frame after every row. Dust Build Up WEEKLY Inspect the WaterRower M1 Dust tank and belts regularly. Clean the top of the rails where the wheels run. To do this, run a damp cloth along the top and sides of the rails.
EVERY MONTH Handle Strap Every 6 months, review the stitching and wear on the handle strap. If you notice excessive wear, replace the handle. Fraying can be caused by incorrect use. Please see instructions on our service site for replacing the handle. EVERY 3 MONTHS Check the Tension of the Recoil To test the strength of the recoil, first remove the...
EVERY 6 MONTHS Water condition We have included purification tablets in the kit. We recommend adding 1 tablet to the water every 6 months. If the water turns cloudy and the tablet does not clear up the water, then it may be best to change out the water.
EVERY 1 TO 2 YEARS Replace the Batteries If the monitor readings begin to fade or are incorrect, we recommend changing the batteries. Four AA batteries are located behind the monitor. Using a Phillips screwdriver, unscrew the two screws, one on left and one on the right of the monitor, and gently lift to access the battery pack located behind the monitor.
Page 9
Tie Rod Assembly (4) mbly itor WRPT004 WRPB505 Tank Assembly M1 Button with Clutch Screw Kit WRPB510 M1 Front End Pad Assembly WRPB505 M1 Button Head Cap Screw & Washer Set WRPS201 M1 M8x30mm Button Cap Screws WRPD510 M1 Dolley...
TROUBLESHOOTING The Monitor Turns On but Does Not Start MONITOR Check the connection of the sensor cable and the monitor cable. Check that the wiring on both the monitor and sensor cable is intact. Remove the top deck cover and check the position of the sensor disk underneath the top deck.
Page 11
2. Use a dryer sheet or anti-static spray to clean the sensor and sensor disk. 3. If in direct sunlight, move your WaterRower to the shade. The S4 sensor is optical and light may interfere with readings.
If this does not solve the problem, determine where the paddle is rubbing in the tank: right side/ left side, top/bottom or front/back of the tank. Please refer to the Troubleshooting section on our Service website www.waterrowerservice.com, or contact your nearest WaterRower office. You can email: support@waterrower.com.
Replace the bungee cord if necessary (refer to page 7). Please contact support@waterrower.com or call your nearest WaterRower office to order a new bungee. Ensure the seat is correctly positioned on the rails. SEAT The rail extrusions and the guide wheels are under the lip on the extrusion.
If there are any other sounds, please determine where the sound is coming from and contact your nearest WaterRower office (details on back page). Tank is Leaking Water TANK First check the level of water is not filled above the maximum level.
Page 15
To help a customer service representative expedite your call, please have your serial number available; the serial number of your rower can be found on a silver sticker attached to the back of your monitor WaterRower Made in USA US +1 (401) 247 7742 • UK +44 (0)20 8749 9090 DE +49 (0)5921 1798400 •...
Page 16
560 Metacom Avenue 72 South Street The Vale, London W3 7QE Warren, RI 02885 Rydalmere NSW 2116 Australia Tel: +44 (0)20 8749 9090 Tel: +1 (401) 247 7742 Tel: +61 (0)2 9681 4221 info@waterrower.co.uk info@waterrower.com info@waterrower.com.au www.waterrower.co.uk www.waterrower.com www.waterrower.com.au WRM7074...