Samsung CLX-8540ND Series User Manual page 129

Message Meaning
The toner cartridge
[xxx] toner
you have installed is
cartridge is not
not for your machine.
compatible. Check
userís guide
The toner cartridge is
[xxx] toner
not installed or the
cartridge is not
CRUM (Consumer
installed. Install it
Replaceable Unit
Monitor) in the
cartridge is not
properly connected.
DC motor does not
There is a problem in
operate: [zzz]. the control of DC
Please turn off motor unit.
then on
Did not supply
Not supplied toner to
enough [xxx] the imaging unit.
toner. Remove
seal tape &
reinstall
The machine received
Did not supply
several papers with
enough [xxx]
many images, and it
toner. Please
cannot supply the
open/close door
toner properly.
The imaging unit has
End of life,
reached its life span.
Replace with new
[xxx] imaging unit
A toner cartridge has
End of life,
reached its estimated
Replace with new
cartridge life. The
[xxx] toner
printer stops printing.
cartridge
Fax memory is There is no more
almost full. Print
available fax memory.
or remove No more fax data can
received fax Job
be received.
Fax memory is full.
Available fax memory
Print or remove is now 1MB.
received fax Job
Suggested solutions
Install a Samsung-
genuine toner
cartridge, designed
for your machine.
Try to reinstall the
toner cartridge.
Turn the machine off
and turn it on again. If
the problem persists,
please call for
service.
• Remove the
sealing tape from
the imaging unit.
• Thoroughly roll the
toner cartridge five
or six times, and
reinstall it.
• Turn the machine
off and turn it on
again.
Check the toner
cartridge and
redistribute the toner.
(Page 13.3) If the
problem still persists,
please call for
service.
Replace the imaging
unit.
Replace the toner
cartridge with a
Samsung-genuine
toner cartridge.
(Page 13.4)
Delete the received
fax data in the
memory. Call for
service to delete fax
memory.
Delete the received
fax data in the
memory to secure
memory. Call for
service.
14.11
Message Meaning
The finisher cover is
Finisher door is
not securely latched.
open. Close it
Finisher error:
There is a problem in
[zzz]. Please turn the finisher unit.
off then on
Fuser error: [zzz].
There is a problem in
Please turn off the fuser unit working.
then on
Fuser unit is not
The fuser unit is not
installed correctly. installed or correctly.
Install it
LSU error: [zzz].
There is a problem in
Please turn off the control of LSU unit.
then on
Motor does not
There is a problem in
operate: [zzz]. the control of motor
Please turn off
unit.
then on
Original paper
The lead edge of the
does not feed in document failed to
scanner actuate the scan
sensor within the
correct time after
actuating the
registration sensor.
Original paper is
Oversized document
too long for or double-feeding of
scanner. Check
originals.
size
Original paper jam The originals are
in front of scanner jammed in DADF.
<Troubleshooting>
Suggested solutions
Close the finisher
until it locks into
place.
Turn the machine off
and reinstall the
finisher again. Check
that the finisher cable
is connected
properly. If the
problem persists,
please call for
service.
Turn the machine off
and turn it on again. If
the problem persists,
please call for
service.
Install the fuser unit.
Call for service.
Turn the machine off
and turn it on again. If
the problem persists,
please call for
service.
Turn the machine off
and turn it on again. If
the problem persists,
please call for
service.
Open the DADF
cover and remove
jammed original.
(Page 14.1)
Open the DADF
cover and remove the
jammed original.
(Page 14.1)
Check the document
size whether it is
supported.
(Page 17.1)
Open the DADF
cover and remove the
jammed original.
(Page 14.1)