Understanding Display Messages - Samsung CLX-6200FX User Manual

UNDERSTANDING DISPLAY MESSAGES

Messages appear on the control panel display to indicate the machine's
status or errors. Refer to the tables below to understand the messages'
meaning and correct the problem if necessary. Messages and their
meanings are listed in alphabetical order.
• If the message is not in the table, cycle the power and try the
printing job again. If the problem persists, call for service.
• Some messages may not appear in the display depending on
options or models.
• xxx indicates the media type.
• yyy indicates the tray.
MESSAGE MEANING
[COMM. Error] The machine has a
communication
problem.
[Incompatible] The machine has
received a fax from
which is registered as
a junk fax.
[Line Error] Your machine cannot
connect with the
receiving fax machine
or has lost contact
because of a problem
with the phone line.
[No Answer] The receiving fax
machine has not
answered after
several redial
attempts.
[Stop Pressed] Stop/Clear has been
pressed during an
operation.
[yyy] There is no paper in
the tray.
Paper Empty
[yyy] The paper size
specified in the printer
Paper Mismatch
properties does not
match the paper you
are loading.
[yyy] The tray cassette is
not properly closed.
Cassette Out
Adjusting... The machine is
adjusting the color
Registration
registration
Authentication The ID or password
you entered is
Failure
incorrect.
78 _Troubleshooting
SUGGESTED
SOLUTIONS
Ask the sender to try
again.
The received fax data
will be deleted.
Reconfirm junk fax
setup. See page 56
Try again. If the problem
persists, wait an hour or
so for the line to clear
and try again.
Or, turn the ECM mode
on. See page 56.
Try again. Make sure
that the receiving
machine is operational.
Try again.
Load paper in the tray.
Load the correct paper in
the tray.
To close the tray, lower
the rear edge, align it
with the slot, and slide it
into the printer.
Wait a few minutes.
Enter the correct ID or
password.
MESSAGE MEANING
Cancel? Your machine's
memory has become
Yes
full while trying to
store an original into
memory.
Connection Error Connection with the
SMTP server failed.
Connection Failed The protocol you have
entered is not
supported or server
port is wrong.
DADF Cover The DADF cover is
not securely latched.
Open Error
Data Read Fail Time expired while
reading data.
Check USB Mem.
Data Write Fail Storing to the USB
memory failed.
Check USB Mem.
Document Jam The loaded original
has jammed in the
DADF (or ADF).
Door Open/Check The front cover is not
securely latched.
Transfer Belt
Duplex Jam 0 Paper has jammed
during duplex printing.
Check Inside
This is applicable only
to machines with this
feature.
Duplex Jam 1 Paper has jammed
during duplex printing.
Open/Close Door
This is applicable only
to machines with this
feature.
Enter Again You entered an
unavailable item.
File Access Login to the network
server was
Denied
successful. However,
access to the file on
the network server
was denied.
File Format The selected file
format is not
Not Supported
supported.
SUGGESTED
SOLUTIONS
To cancel the fax job,
press the OK button to
accept Yes.
If you want to send those
pages that have been
successfully stored,
press the OK button to
accept No. You should
send the remaining
pages later, when
memory is available.
Check the server
settings and the network
cable.
Check the protocol or
server port.
Close the DADF cover
until it locks into place.
Try again.
Check the available USB
memory space.
Clear the jam. See page
71.
Close the cover until it
locks into place.
Clear the jam.
See page 73.
Clear the jam.
See page 73.
Enter the correct item
again.
Change the server
settings.
Use the correct file
format.