Advertisement
Advertisement
Related Manuals for Dynaudio Xeo 10
Summary of Contents for Dynaudio Xeo 10
- Page 1 Xeo 10/20/30 Owner’s manual...
- Page 2 Hello Welcome to Dynaudio Xeo. We’ve taken care of the tech; you take care of the music.
-
Page 3: Table Of Contents
Connection options Connections and control elements Division into audio zones Elements on the rear panel Components of the Xeo system Buttons on top of the cabinet (Xeo 10) The Xeo system Remote control Combination examples Declaration of Conformity (EU only) -
Page 4: Introduction
Dynaudio About this product The active Xeo 10/20/30 speakers are equipped with powerful integrated amplifiers and allow for the direct connection of various analog and digital audio sources. A Bluetooth interface enables the operation of Bluetooth devices and plays them back in optimal sound quality. -
Page 5: Important Safety Instructions
Dynaudio Xeo 10/20/30 Important safety instructions The quintessential Important Read these instructions. Keep these instructions. safety Heed all warnings. Follow all instructions. wireless hi-fi instructions Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. -
Page 6: Warning
Do not attempt to start up a damaged voltage is present inside the speakers. device. If the contents are incomplete or damaged, please contact your Dynaudio ► Use the supplied power cable to connect the speakers to the mains voltage. Make Xeo distributor. -
Page 7: Xeo 10/20/30 Speakers
1 stereo cable (RCA – RCA, length: 1.5 m) (Xeo 10 only) The Xeo 10/20/30 set consists of a master and a slave unit. The master unit carries the 1 optical cable (Toslink – Toslink, length: 1.5 m) (Xeo 10 only) audio input interfaces. -
Page 8: Connections And Control Elements
Connections and control elements / Connecting and setting up Buttons on top of the cabinet (Xeo 10) Speaker on/off ► Press to switch on the speakers. The Xeo 10 will scan the inputs for a signal. Connecting ► Press and hold to switch off the speakers. -
Page 9: Remote Control
► Press master speaker (see „Connection options“ on page 13). on top of one of the speakers (Xeo 10) or point the remote control at a After it is turned on, the speaker automatically searches for an audio signal and then speaker and press plays it back immediately. - Page 10 Dynaudio Xeo 10/20/30 Fixing the volume Fixing the Status LEDs on the front You can set the speaker to a higher volume using the function to fix the volume. This setting also remains in effect in standby mode. If a signal source is connected to the...
- Page 11 Xeo components. You can ask your Dynaudio Xeo distributor for assistance at any time Or go to dynaudio.com/support to read the FAQ or to contact the Customer Support Team. Further information can also be found on the Xeo website at dynaudio.com/xeo...
- Page 12 100 mm apart. direct sunlight, heat, or moisture. Desk stand – Do not place the speakers The Dynaudio desk stand for Xeo 10 is near devices with strong an elegantly designed stand for placing electromagnetic radiation or the speakers on a desk or shelf.
- Page 13 Connection options Dynaudio Xeo 10/20/30 Connection options ► Connect your signal source to the appropriate input on the Xeo 10/20/30 speaker. ► Following table gives a selection of signal sources and options for connecting to the Xeo speaker. Your signal source Signal source Xeo 10/20/30...
- Page 14 Hub or Connect and its connected signal sources. Dynaudio Connect and The Dynaudio Connect and Xeo Hub are the control centres for Xeo Hub the Xeo system. Both offer a new level of wireless connectivity Green and convenience.
- Page 15 Connection options Combination examples Below you will find several examples of Xeo component combinations. The high level of flexibility in the Xeo system enables even more variants. Ask your Dynaudio distributor to find the perfect solution for your needs. Direct wired:...
- Page 16 Dynaudio Xeo 10/20/30 Connection options Declaration of Conformity (EU only) Dynaudio A/S hereby declares, that the product Dynaudio Xeo 10 / Xeo 20 / Xeo 30 is in conformity with the following directives: • 2001/95/EF (Product Safety) • 2014/53/EU (RE directive) IC NOTICE •...
- Page 17 7.1x12.6x10.1in 6.8x10x6.1in Dimensions with feet/grille (WxHxD) 228x852x275mm 180x320x265mm 173x255x164mm An update to this manual may be necessary due to product improvements and new functions. 9.0x33.5x10.8in 7.1x12.6x10.4in 6.8x10x6.5in The latest version of this manual is available on the Internet at dynaudio.com/support/manuals...
- Page 18 Xeo 10/20/30 Designed and engineered by Dynaudio Labs in Denmark Dynaudio A/S 8660 Skanderborg Denmark dynaudio.com Owner’s manual Xeo 10/20/30, EN - Item no. 45563101A. All text and image copyrights reserved. Subject to change without notice.