Page 2
Other trademarks and trade names are those of their respective owners. An update to this manual may be necessary due to product improvements and new functions. The latest version of this manual is available on the Internet at www.dynaudio.com/support/manuals Dynaudio...
The speaker Xeo 4 and Xeo 6 minimize your system to the essentials: The audio source and the speakers. A high-end digital amplifier is integrated into the speakers, so speaker cables and external amplifiers become obsolete.
Control elements Xeo Hub Connections and control elements Connection Xeo speakers Connections and control elements Cloth cover Setting up Interface display Connecting the power cable and adjusting Switching on Selecting a Hub or input/autoplay function Fixing the volume Standby Dynaudio...
15. To completely disconnect this equipment from the mains, disconnect the power supply cord plug from the receptacle. 16. The mains plug of the power supply cord shall remain readily operable. Xeo 4 / Xeo 6...
Page 6
► Do not operate defective speakers or Xeo power supplies and disconnect them from the mains voltage if defect. Please contact your Dynaudio Xeo distributor if you have any problems. Dis- tributor addresses can be found in the Internet at www.dynaudio.com.
Transport damage may be expected if the packaging is already severely harmed. Do not attempt to commission a damaged device. If the contents are incomplete or damaged, please contact your Dynaudio Xeo distributor. Distributor addresses can be found in the Internet at www.dynaudio.com.
1 optical digital cable (Toslink – Toslink, length: 1.5 m) 1 USB cable (USB – mini USB, length: 1.5 m) 1 Xeo first time setup manual (quick guide for installation, not shown) Xeo 4 / Xeo 6...
The Xeo system Components Xeo 2 The active Xeo 2, Xeo 4 and Xeo 6 speakers receive the wireless signals from Xeo 4 the Hub or Connect and play them back in optimal sound quality. They have an Xeo 6 integrated amplifier and can be controlled with the Xeo remote control.
Combination examples Below you will find several examples of Xeo component combinations. The high level of flexibility in the Xeo system enables even more variants. Ask your Dynaudio distributor to find the perfect solution for your needs. Xeo 2 only:...
Page 12
(e.g. active subwoofer, active Hub or Connect speakers, or power amplifier and passive speakers) This example would also be possible with only Link a Hub, Link, and active component. NOTE: The Extender and Link may also be combined. Figures show a Hub. Dynaudio...
Connection and operation This section describes the connections and control elements for the Xeo components. Please contact your Dynaudio Xeo distributor if you have any problems with connection and start-up. Distributor addresses can be found in the Internet at www.dynaudio.com.
Connect devices here that have an optical digital output. Coax In Input for electrical digital cable (coax) Connect devices here that have an electrical digital output. USB In Input for USB cable Connect your computer’s USB output here. The Hub will then work as a sound card. Dynaudio...
3. Connect the Hub to the mains voltage using the POWER connection and the Xeo power supply unit. Do not use a different power supply unit! NOTE: If you connect Xeo Hub via a USB cable to a computer (that is switched on), you do not need an additional mains connection. Xeo 4 / Xeo 6...
• I = The speaker is on. The speaker can be activated and deactivated via the remote control. If the speaker is activated and there is no signal, it will switch to standby mode. • O = The speaker is completely off. Mains socket To connect the speaker to the mains voltage. Dynaudio...
CAUTION Spikes with pointed ends Xeo 6 floor-standing speakers are delivered with spikes for permanent installation on the floor. The pointed ends of the spikes may result in injuries and damage delicate floors. ► Pay attention that you do not injure yourself with the spikes.
The LEDs are illuminated one by one. The speaker is being switched on. Switch-off process The LEDs go out one by one. The speaker is being switched off. In the final state, only one LED is illuminated dimly in red. Dynaudio...
Page 19
The red LED is blinking; the lights in the System synchronization white LEDs move back and forth. Volume, mute A number of white LEDs are illuminated. The number of LEDs indicates the selected volume. The first LED is blinking. The speaker is muted. Xeo 4 / Xeo 6...
Hub or input if you want to play back a different signal source. To select a different Hub or input: ► Press HUB A, B, or C or INPUT 1, 2, 3, or 4 on the remote control. ▼ The selected signal source will be played back. Dynaudio...
Low-power standby mode power consumption is <0.5 W. ► To completely switch off the speaker, turn the POWER switch on the rear to OFF. ▼ However, the speaker can then no longer be switched on via the remote control. Xeo 4 / Xeo 6...
Do not operate such electrical devices near Xeo components. You can ask your Dynaudio Xeo distributor for assistance at any time. Or go to www.dynaudio.com/support to read the FAQ or to contact the Customer Support Team. Further information can also be found on the Xeo website at www.dynaudio.com/xeo...
Dimensions (W x H x L) 170 x 282 x 246 mm / 6.7 x 11.1 x 9.7" 170 x 854 x 246 mm / 6.7 x 33.6 x 9.7" Connections Wireless in 2.4/5 GHz, 16 bit/48 kHz from Hub/Connect Xeo 4 / Xeo 6...
Toslink – Toslink * up to 3 generation Hard disk, network player, CD player Line out 1: Line in RCA – RCA * If available Optical* 2: Optical In Toslink – Toslink Electrical* 3: Coax In Coax – coax – Dynaudio...
Page 25
1: Line in RCA – RCA Subwoofer Analog output 1: Line in RCA – RCA – AV receiver, AV processor Optical 2: Optical In Toslink – Toslink – Pre-out, main out 1: Line in RCA – RCA Xeo 4 / Xeo 6...
The Xeo speakers (as well as Xeo Link) can be assigned to an audio zone using the Zone selector switch. All components assigned to a zone can be operated together via the remote control. The picture below shows a possible zone configuration. Green Green Blue Zone Green Blue Zone Green Blue Blue Zone Dynaudio...
Declaration of Conformity (EU only) Dynaudio A/S hereby declares, that the products Dynaudio Xeo 4 and Xeo are in conformity with the following directives: • 2001/95/EF (Product Safety) • 2006/95/EF (Low Voltage directive) • 2004/108/EF (EMC directive) • 1999/5/EC (R&TTE directive) •...
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. Dynaudio...
5250 – 5350 MHz et (iii) 5650 – 5850 MHz. IIs peuvent provoquer des perturbations electromagnetiques sur les appareils de type LELAN (réseau de communication local sans licence) ou les endommager. Xeo 4 / Xeo 6...
Need help?
Do you have a question about the Xeo 6 and is the answer not in the manual?
Questions and answers