Supermicro SuperServer 5017P-TLN4TF Quick Reference Manual

SuperServer 5017P-TLN4F/TF Quick Reference Guide
Board Layout
1 2
JVGA1
JCOM1
JLAN2 JLAN1 J1 J3
MH4 MH4 1 JPUSB1
JWD1
LED2
U21 U7 U10 U22
U57
JPB1 JP1
SP1
U6
CPU1
U3
JDIMM1
I-SATA5 I-SATA4
JDIMM2
I-SATA3 I-SATA2
P1-DIMMA1
P1-DIMMB1
I-SATA1 I-SATA0 LED1
JD1 USB6/7
JTPM1:TPM/PORT80
MH6
JSD1:SATA
DOM POWER
JPI2C1
PWR I2C
JWP1:WRITE PROTECT
9 8 7 6 5
No.
Description
1 PCI-E x16 Gen 3 Slot
2 CPU
3 DIMMA1
4 DIMMB1
5 I-SATA5, I-SATA4, I-SATA3, I-SATA2 (Black connector: SATA2)
6 JSD1 = DOM (Disk on Module) Power Connector
7
I-SATA0, I-SATA1 (White connector: SATA3)
8
JF1 = Front panel control header
9 JBT1 = CMOS Clear
Two 2.5" HDDs
In a Double Bracket, Four HDD's Total,
No Expansion Card
MEMORY
The SO DIMM Socket
COM1
COM2
Position the SO DIMM
JCOM2
module's bottom key so it
aligns with the receptive
point on the slot. Take
MH2 note of the module's side
Align
notches and the locking
clips on the socket.
U26
Insert the SO DIMM module
straight down.
MH7
JPW1
4 3
Press down until the module
locks into place. The side
clips will automatically secure
the SO DIMM module, locking
it into place.
To Remove:
Use your thumbs to gently
push the side clips near both
ends away from the module.
This should release it from
the slot. Pull the SO DIMM
module upwards.
Hard Drive Configuration Options
Two 2.5" Hard Drives
and One Full-Height,
Half-Length Expansion Card
Front view & Interface
6 4 3
No. Description
Power Button
1
Reset Button
2
3 Power LED
4 Device Activity LED
5 LAN1 LED & LAN2 LED
6
Information LED
Informational LED
Status Description
An overheat condition has occured.
Continuously
(This may be caused by cable congestion.)
on and red
Blinking red (1Hz) Fan failure, check for an inoperative fan.
Blinking red Power failure, check for a non-operational
(0.25Hz) power supply.
Solid blue Local UID has been activated.
Use this function to locate
Blinking blue Remote UID is on. Use this function to identify
(300 m/s) the server from a remote location.
One 3.5" Hard Drive
Two 3.5" Hard Drives
and Low Profile
and No Expansion Card
Expansion Card
Note: Compatibility of add-on cards dependent on component height, etc.
http://www.supermicro.com
Rear View
9 8
10 7 6 5 4 3 2
No.
Description
Expansion Slot
1
2 VGA Port
3 Gb LAN 3/4 (5017P-TLN4F only)
2 1
Gb LAN 1/2
4
5 USB Port 8/9
6 USB Port 4/5
7
COM Port 1
8
PS/2 Keyboard/Mouse
9 Dedicated IPMI LAN Port
10
Power Supply
Beep Codes
BIOS Beep Codes
Error Message
Beep Code/LED Description
1 long + two short beeps Video Video configuration error
Memory No memory detected
1 repetitive long beep
1 continuouse beep Overheat System overheat detected
w/Overheat LED
1 continuouse beep Fan Fan failure detected
w/Fan Fail LED blinking
Display memory
8 short beeps Display
read/write error
Caution

!
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning
before connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm

!
WARNING:
To reduce risk of electric shock/damage to equipment,
disconnect power from server by disconnecting all power
cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap

!
CAUTION:
Always be sure all power supplies for this system have
the same power output. If mixed power supplies are
installed, the system will not operate.
For more information go to :
http://www.supermicro.com/support
MNL-1368-QRG ÌMNL-1368-QRG4Î
1