Supermicro X9SRi3F Quick Reference Manual

S
UPERMICR
R
X9SRi (-F)(-3F) / X9SRE (-F)(-3F)
Q r g
uICk eferenCe uIde
r 1.0
evIsIon a
Motherboard Layout and Features
Supported on models with "F" designation only
12 11
Available on the X9SRE series only.
15
9
13
14
A
C UID_LED
UID
UID_SW
MH1
2 1
DP3
10
1
16
9
5 3
JPB: BMC
1-2 Enable
JSTBY : Wake on Lan 2-3 Disable
17
1
PCIE6
SLOT4
3
1
18
SLOT5
SLOT6
JIPMB1 JIPMB1
20 19
19
1
2
20
2
21
7
10
+
2 1
22 1
7
1
23 2
SLOT3
7
10
2 1
24
8 7
25 2
1
SLOT2
X_BT1
MH5
8 7
SLOT1
58
ON:RECOVER BIOS
JPBIOS_RCV1 OFF:NORMAL
1
3
JPME_RCV1
3 59
26 R625
ON:ME IN FORCE UPDATA MODE
OFF:NORMAL
JRK1
Pin1:RAID_KEY_PCH
Pin2:Ground
Pin3:PCH_DYN_SKU
60
27
61
62 63
28
JBT1
1
29
3
30 SAS5 SAS6 SAS7 I-SATA3 I-SATA3 I-SATA2 I-SATA2 1
2
2
7
MH7
FANA
31
I-SATA 3.0
40 41
35
33
Supported on
32 34
models with "3"
I-SATA 2.0
designation only
36 37 38 39
CPU Installation Heatsink Installation
Screw #1
Align Socket Keys
Motherboard
Mounting Hole
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.
C I
ontaCt nformatIon
• www.supermicro.com (Email: support@supermicro.com)
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
2
3
5
6
1
8 7
4
JVGA JCOM1
FAN4 COM1
55
FAN4
JPL1/2: LAN
1-2 Enable
JPL2 JPL1 2-3 Disable 54
LAN2 JLAN2 LAN1
USB0/1 JPUSB1
1 3
JVR1
57 56
CLOSE 1st
DIMMC1
Socket R
DIMMC2
LGA 2011
CPU
DIMMD1
DIMMD2
OPEN 1st
DIMMB2
DIMMB1
DIMMA2
DIMMA1
DIMM_C1
JTAG1
12
JPW2 JPW2
JVR2
52
53
JD1:
1-3: PWR LED
JWD1:Watch Dog 4-7: SPEAKER
1-2:RST
2-3:NMI
JVR6 5
JVR5
JVR4
47 JVR3
1
51
1
3
1
JF1
A
2 20
C
FAN3
1 1 3 1 7 SP1
44
46 49
42
43
50
45
48
= mounting hole
Front Panel Control (JF1)
Screw #4
20 19
Ground
Screw #2 NMI
X X
Vcc
Power LED
HDD LED Vcc/UID Switch
Screw #3 NIC1 LED Vcc
Vcc
NIC2 LED
OH/Fan Fail LED
Vcc/Blue UID LED
Power Fail LED
Vcc
#3~4 Reset Button
Ground
Power Button
Ground #1~2
2 1
P C
aCkage ontents
(Applies to individual-pack only)
• One (1) Supermicro Motherboard
• Eight (8) SATA Cables
• One (1) I/O Shield
• One (1) Quick Reference Guide
Jumpers, Connectors and LED Indicators
Jumpers
11,12 JI2C2,JI2C1 SMB to PCI-E Slots On (Enabled)
13 JPG1 Onboard VGA Enable Pins 1-2 (Enabled)
17 JPB1 BMC Enable (for "F" models only) Pins 1-2 (Enabled)
45 JWD1 Watch Dog Reset Pins 1-2 (Reset)
54 JPUSB1 USB Power Select Pins 1-2 (Dual Power)
56, 57 JPL1,JPL2 LAN1,LAN2 Enable Pins 1-2 (Enabled)
58 JPBIOS1 BIOS Recovery Pins 1-2 (Normal)
59 JPME1 Intel ME Mode Select Pins 1-2 (Normal)
61 JBT1 CMOS Clear Short contact pads to reset CMOS
Connectors
1 JKBMS1 Backpanel Keyboard and Mouse Port
2 JLAN IPMI LAN Port ("F" models only)
3, 4 USB 0/1 USB 2.0 Port 1, USB 2.0 Port 2
5, 16 JCOM1, JCOM2 COM1 Backpanel Serial Port, COM2 Serial Port Header
6 JVGA Backpanel VGA Port
7, 8 JLAN1, JLAN2 Backpanel Gbit LAN Ports 1, 2
10 UID_SW Unit ID Switch
15 JSTBY1 Legacy Wake on LAN header
18 JIPMB1 System Management Bus Header for the IPMI Slot
19 JTPM1 Trusted Platform Module (TPM) Header
20,22,23 JUSB 4/5, 6/7, 8/9 Front Accessible USB Connections (via 3 Headers)
21 JOH1 Overheat LED/Fan Fail
24, 25 3-SGPIO1,3-SGPIO2 Serial General Purpose I/O Headers for SAS
26 JUSB2 Internal Type A USB port
27~30, 32~35 SCU0~7 Internal Serial-Attached SCSI/SAS ports ("3" models only)
31,42,49,50,55 FAN A, FAN 3,2,1,4 Internal Fan headers
36,37,38,39 I-SATA 5,4,3,2 SATA 2.0 ports (3Gb/s)
41, 40 I-SATA 0/1 SATA 3.0 ports (6Gb/s)
43 JF1 Front Panel Control Header
44 JTAG1 Factory Reserved
46 JD1 Power LED / Speaker Header (Pins 4~7: External
Speaker)
48 JL1 Chassis Intrusion Header
51 JPI2C1 Power Supply SMBus I2C Header
52 JPW1 24-pin Main ATX Power Connector
53 JPW2 8-pin Secondary Power Connector
60 JSD1 Disk On Module (DOM) Power
62,63 T-SGPIO2,T-SGPIO1 Serial General Purpose I/O Headers for SATA
LED Indicators
9 UID LED UID (Unit ID) LED Blue: Solid On
14 DP3 IPMI Heartbeat Green/Blinking
47 DP2 Power On LED Green: Solid On
Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators.
Memory Support
The X9SRi/ X9SRE motherboard series suppor ts up to 256GB of
1600/1066/1333 MHz ECC/Non-ECC DDR3 DIMMs in eight (8) memory slots
(UDIMM/RDIMM).
Note: For memory optimization, use only DIMM modules that have been validated by Supermicro.
For the latest memory updates, please refer to our website at http://www.supermicro.com/
products/motherboard.
DIMM Memory Installation
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the
following order: DIMMA1, DIMMB1, DIMMC1, DIMMD1 then DIMMA2, DIMMB2,
DIMMC2, DIMMD2.
• Always use DDR3 DIMM modules of the same size, type and speed.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed
of the slowest DIMM.
• The motherboard will support odd-numbered modules installed (1 ,3 ,5 ,or 7
modules). However, for best memory performance, install DIMM modules in
pairs.
Recommended Population (Balanced)
DIMMA1 DIMMB1 DIMMC1 DIMMD1
2GB 2GB
2GB 2GB 2GB 2GB
2GB 2GB 2GB 2GB
4GB 4GB
4GB 4G 4GB 4GB
4GB 4GB 4GB 4GB
Note: Up to 256GB of memory are supported. See chapter 2 of the User Manual for
complete memory population information.
Back Panel IO Connectors
C
A
F
UID: On
BMC/IPMI Normal
System is On
D
B
E
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
Motherboard edge
CPU
DIMMA2 DIMMB2 DIMMC2 DIMMD2 Total
System
Memory
4GB
8GB
2GB 2GB 2GB 2GB 16GB
8GB
16GB
4GB 4GB 4GB 4GB 32GB
A. Mouse F. COM1
B. Keyboard G. VGA
C. IPMI (-F only) H. LAN1
D. USB Port 2 I. LAN2
G
E. USB Port 1
H I