Supermicro X9SRW-F Quick Reference Manual

S
UPERMICR
R
X9SRW-F
Q R G R . 1.00
UICK EFERENCE UIDE EV

Motherboard Layout and Features

7
10
6
11
JUIDB1
JI2C2/JI2C3 14
1-2:Enable UID JVGA1 VGA
2-3:Disable
JPG1: VGA
1-2:Enable
12 2-3:Disable
8
LED2
1
JLAN2
13
9 LAN2
SXB1A
14 BD1
15
SXB1A: LEFT_WIO_UP
SXB1B: LEFT_WIO_MIDDLE
SXB2: RIGHT_WIO JPG1
16
52
JWD:WATCH DOG TIMER
1-2:RST(DEFAULT)
2-3:NMI
17
JPME1:
SAS3 SAS4 ON:ME RECOVERY
OFF:NORMAL
61
18
SAS1
19
SAS2
DESIGNED IN USA
20 21
22 23
CLOSE 1st
24 25
26
DIMMD2
DIMMD1
DIMMC2
DIMMC1
CPU1
JL1
27
FAN4
20
2
FAN5 JF1
4 1
19
28
31
29
30

CPU Installation

Heatsink Installation

Screw#1
Align Socket Keys
Motherboard
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this
C I
ONTACT NFORMATION
• www.supermicro.com (Email: support@supermicro.com)
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
5
1
2
4
COM1
JCOM1
JPL1:LAN1
1-2:ENABLE
2-3:DISABLE
JPL2:LAN2
1-2:ENABLE
2-3:DISABLE
JWD:
3 1-2:RST
2-3:NIMI
JPMB
JIPMB1
49
JLAN1
LAN1
J17
JWP1:
WRITE PROTECT
J26
48
USB
50
51
J23
1 47
USB
JWD JOH1
JOH1:OVER HEAT LED
1 1 46
BT1
1
3 3
54
1 45
53
3
55 JWP1 3
44
1
3
JSTBY1
56
43
JPB1: BMC
1-2:ENABLE
2-3:DISABLE JBT1 JD1:
1-2:PWR_LED
JPB1 4-7:SPEAKER
57
1 42
JPME1
58 7
JP3
1
41
7
59 JI2C1
ON:Enable
OFF:Disable
1
SP1
60 40
JD1
8 7
2
1
39
8 7
1
38
H-HS2_2
5
CPU
37
36
DIMMB2
DIMMB1
Socket R DIMMA2
LGA 2011
DIMMA1
CPU
JPWR1 1
OPEN 1st 35
34
24
FAN2 FAN1
33
32
= mounting hole

Front Panel Control (JF1)

20 19
Ground NMI
X X
Vcc
Power LED
Screw#2
HDD LED Vcc
Vcc
NIC1 LED
Vcc
NIC2 LED
OH/Fan Fail LED UID LED
X
X
#3~4 Reset Button
Ground
Ground #1~2 Power Button
2 1
guide.
P C
ACKAGE ONTENTS
(Applies to individual-pack only)
• One (1) Supermicro Motherboard
• Eight (8) SATA Cables
• One (1) I/O Shield
• One (1) Quick Reference Guide

Jumpers, Connectors and LED Indicators

Jumpers
10 UID Unit ID Switch Off (Disabled)
11, 12 JI2C3/JI2C2 SMB to PCI Slots On (Enabled)
16 JPG1 Onboard VGA Enable Pins 1-2 (On)
45 JWP1 BIOS Write Protect Pins 1-2 (Normal)
46 JPL1 LAN1 Enable Pins 1-2 (Enabled)
50 JWD Watch Dog Timer Reset Pins 1-2 (Reset)
52 JP3 BIOS Recover Pins 2-3 (Open)
54 J30 VRM SMB Data (to BMC or PCH) Pins 1-2 (BMC, Normal)
55 J29 VRM SMB Clock (to BMC or PCH) Pins 1-2 (BMC, Normal)
56 JPB1 IPMI/BMC Enable Pins 1-2 (Enabled)
57 JPME1 Intel ME Mode Select Pins 1-2 (Normal)
58 JBT1 CMOS Clear Short contact pads to clear CMOS
Connectors
1 JCOM1 Back panel Serial Port Connector
2, 4 USB0/1, USB2/3 Back panel USB 2.0 ports
3 IPMI Back panel IPMI LAN Port
5, 6 JLAN1/JLAN2 Back panel LAN1 / LAN2 Ethernet Ports
7 JVGA1 Back panel VGA Port
14, 17 SXB1A, SXB1B Supemicro riser card slot (P/N RSC-R1UW-2E16)
15 SXB2 Supemicro riser card slot (P/N RSC-R1UW-E8R)
18, 19, 60, 61 I-SAS 0,1,3,2 (SATA 3.0) I-SATA 3.0 ports (supports up to 6Gb/s)
20, 21 I-SATA0, I-SATA1 (SATA 3.0) Internal SATA ports (up to 6Gb/s)
22, 23, 24, 25 I-SATA 2,3,4,5 (SATA 2.0) Internal SATA ports (up to 3Gb/s)
26 JSD1 SATA DOM (Disk On Module) Power Connector
27 JL1 Chassis Intrusion Header
28,29,31,32,33 FAN 5,4,3,2,1 Front Panel Control Header
30 JF1
34 JPW1 24-pin Main ATX Power Connector
35 JPW2 8-pin Secondary Power Connector
37 JD1 Pwr LED / Speaker Header (Pins 4~7:Ext Speaker)
38 JPI2C1 Power Supply SMBus I2C Header
39, 40, 41, 42 T-SGPIO1~4 Serial Link General Purpose I/O Headers
43 JTPM1 Trusted Platform Module (TPM) Header
44 JSTBY1 Legacy Wake On LAN Header
47, 48 USB4/5, 8/9 Internal USB 2.0 headers
49 JIPMB1 System Management Bus Header (IPMI Slot)
51 BT1 System Battery
53 JOH1 Overheat LED/Fan Fail
59 SP1 Internal Speaker / Buzzer
LED Indicators
8 LE2 UID LED Blue/Steady UID Switch is On
9 BD1 IPMI Heartbeat Green/Blinking IPMI is enabled
13 LED2 Standby 3.3V Power Green/Steady Standby Power
36 LE1 Power LED Green/Steady System is On/Running
Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators.

Memory Support

The X9SRW Motherboard supports up to 256GB of 1600/1333/1066/800 MHz
ECC/Non-ECC DDR3 DIMMs in eight (8) memory slots (UDIMM/RDIMM).
Note: For memory optimization, use only DIMM modules that have been validated by Supermicro.
For the latest memory updates, please refer to our website a at http://www.supermicro.com/
products/motherboard.

DIMM Memory Installation

DIMMA1 (Blue Slot)
DIMMA2
DIMMB1 (Blue Slot)
DIMMB2
CPU
DIMMD2
DIMMD1 (Blue Slot)
DIMMC2
DIMMC1 (Blue Slot)

Memory Population Guidelines

When installing memory modules, populate the DIMM slots in the following or-
der: DIMMA1, DIMMB1, DIMMC1, DIMMD1 then DIMMA2, DIMMB2, DIMMC2,
DIMMD2. Populate the blue-colored slots fi rst.
• Always use DDR3 DIMM modules of the same size, type and speed.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed
of the slowest DIMM.
• The motherboard will support odd-numbered modules installed (1 ,3 ,5 ,or 7
modules). However, for best memory performance, install DIMM modules in
pairs.

Recommended Population (Balanced)

DIMMA1 DIMMB1 DIMMC1 DIMMD1 DIMMA2 DIMMB2 DIMMC2
2GB 2GB
2GB 2GB 2GB 2GB
2GB 2GB 2GB 2GB 2GB 2GB
2GB 2GB 2GB 2GB 2GB 2GB 2GB
Note: The motherboard supports up to 256GB of total memory. Please consult the user's manual
for more populating options.

Back Panel I/O Connectors

B
A. COM 1
E
A B. IPMI Port
G H
I
C. USB 2.0 Port 1
D. USB 2.0 Port 0
E. USB 2.0 Port 3
C F F. USB 2.0 Port 2
D
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
DIMMD2 Total
4GB
8GB
12GB
2GB 16GB
G. LAN1
H. LAN2
I. VGA Port