Supermicro X9SKV Quick Reference Manual

S
C
UPERMICR ontaCt
R
• Website: www.supermicro.com
• General Information: marketing@supermicro.com
X9SKV
• Tech Support: support@supermicro.com
Q r g r . 1.00
uICk eferenCe uIde ev • Phone: +1 (408) 503-8000, Fax: +1 (408) 503-8008
Motherboard Layout and Features
Back Panel I/O
Back Panel I/O Connectors
G
B D
E
C F
A
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.
I
f
nformatIon
or your system to work ProPerly
drIvers
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com/CDR_Images/CDR-X9-UP/
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
= mounting hole
A. LAN1 (Bypass Pair 1)
B. LAN2 (Bypass Pair 1)
C. LAN3 (Bypass Pair 2)
H
D. LAN4 (Bypass Pair 2)
E. COM1
F. LAN5
G. LAN6
H. USB0 (2.0)
I. USB1 (2.0)
I
,
Please download the aPProPrIate
/ / ' :
Images user s manual from the lInks below
Jumpers, Connectors and LED Indicators
Jumpers
Settings (Defaults are in Bold)
Jumper Description
JPME2 Intel ME Manufacturing Mode
Pins 1-2 (Normal), Pins 1-2 (Intel ME Manuf. Mode)
JPF1 Front Panel LED select Pins2-3 (Normal), Pins 1-2 (Bypass LAN LED)
JPF2 Front Panel RST Button select Pins2-3 (Normal), Pins 1-2 (FR/NMI)
JBT1 Clear CMOS Short contact pads to clear CMOS
JI2C1/JI2C2 SMB to PCI-Express Slots Pins 1-2 (Open: Disabled), (Closed: Enabled)
JPSLOT1 PCI-E Slot select Pins 1-2 (Slot 7), Pins 2-3 (Slot 6)
Connectors
Connector Description
Please see "Back Panel IO Connectors" below, left
Back Panel I/O
JSTBY1
Provides 5V standby power only, and legacy Wake-On-LAN function
USB 2/3
Front Panel USB 2.0 header for USB 2/3
USB 4
Internal Type A USB Port
COM2
Serial Port header (COM2)
JF1
Front Panel control header (see Front Panel Control (JF1) below, right)
JF2
Front Panel control header (see Front Panel Control (JF2) below)
FAN1~FAN6
System Fan power/control headers (FAN1: CPU Fan)
JD1
External Speaker/Buzzer header (Pins 1-3: Power LED, Pins 4-7:Ext Speaker)
JOH1 System Overheat header
JL1
Chassis Intrusion header
JWOR1 Wake-On-Ring header
I-SATA0/I-SATA1
3Gb/s I-SATA connectors for SATA0 and SATA1
JSD1 SATA DOM (Disk-On-Module) power connector
SP1
Internal Speaker/Buzzer
JPW1
Motherboard 24-pin ATX Main Power connector
JPW2
Motherboard 8-pin ATX CPU Power connector
JTPM1
Trusted Platform Module (TPM) header
LED Indicators
LED Description Color/State
LED5 Power LED
Green/Solid
Front Panel Control (JF2)
8 7
NIC1 (Activity) LED
NIC1 (Link) LED
NIC2 (Activity) LED
NIC2 (Link) LED
NIC3 (Link) LED
NIC3 (Activity) LED
NIC4 (Link) LED
NIC4 (Activity) LED
2 1
Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators.
P C
aCkage ontents
(Applies to individual-pack only)
• One (1) Supermicro Motherboard with CPU and Heatsink Installed
• Two (2) SATA Cables
• One (1) I/O Shield
• One (1) Quick Reference Guide
Memory Support
This motherboard supports up to 32 GB of DDR3 ECC SODIMMs
in 4 SODIMM slots. It supports speeds of up to 1600MHz.
Note: For memory optimization, use only SODIMM modules that have been validated by
Supermicro. For the latest memory updates, please refer to our website at http://www.
supermicro.com/products/motherboard.
DIMM Installation
Towards the CPU
JDIMM1
DIMMA1
JDIMM2
DIMMA2
JDIMM1
DIMMB1
JDIMM2
DIMMB2
Towards the edge of the motherboard
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the
following order: DIMMA2, DIMMB2 and DIMMA1, DIMMB1
Front Panel Control (JF1)
Status
System On/Running
20 19
Ground
NMI
Key
Key
B FP Power LED 3.3V SB
C
HDD LED 3.3V
D
3.3V SB
LAN5 (Link/Activity) LED
E 3.3V SB
LAN6 (Link/Activity) LED
F OH/Fan Fail LED 3.3V
G Power Fail 3.3V
Ground
Ground
2 1
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
P1-DIMMA1
P1-DIMMA1
Non-Maskable Interrupt
A
Front Panel Power On LED
B
C Hard Drive Activity LED
A
Network Activity LED for LAN5*
D
Network Activity LED for LAN6*
E
F Overheat / Fan Fail LED
- Red, Solid: System Overheat
- Red, Blinking (slow): Fan Fail
- Red, Blinking (fast): Power Fail
G PWR Fail - Red, Solid: Power Fail
Reset Button*
H
H Power Button
I
Reset Button
Power Button Note: Make sure that pins 2-3 of
I
jumpers JPF1 and JPF2 are set
appropriately according to the
configuration you have selected.