Download  Print this page

Honeywell IPCAM-WIC2 Quick Installation Manual

Hd wi-fi indoor video camera.
Hide thumbs
   

Advertisement

IPCAM-WIC2 HD Wi-Fi Indoor Video Camera

Quick Installation Guide

IPCAM-WIC2 is a 1080p, full HD Wi-Fi video camera intended for indoor use with Honeywell Total Connect® 2.0.
Low-light operation is indicated by four red LEDs located on the front of the camera, arranged around the lens.
Camera setup requires a Total Connect® 2.0 account and the new Total Connect 2.0 mobile app. Video Services must
be enabled in AlarmNet 360™. Camera operation requires minimum available bandwidth of 2.1 Mbps.
Google Play and the Google Play logo are trademarks of Google Inc.
For best results, set up only one camera at a time.
Download the Total Connect® 2.0 app from the App Store or on Google Play.
(Look for the red Total Connect logo.)
a.
Turn on your smart device's Bluetooth and
sure the Bluetooth isn't connected to another device and that
you're on the same Wi-Fi network your camera(s) will use .]
b.
Launch the app and sign in with your Total Connect® 2.0
account.
c.
Plug the power supply into an AC outlet, but:.
Don't connect the power supply to the camera yet.
Note that the screens in your app may be a bit different than the
examples seen here.
If your account has more than one Location, select the one where
you're doing camera setup.
You may have to press CAMERAS at the bottom of the screen to see
the Cameras page.
a.
Press ADD CAMERA
b.
Select the type of camera you're installing.
c.
Name the camera and press NEXT.
d.
Connect the power supply to the camera. The LED at the top flashes
a variety of colors. After about a minute, the camera sounds a tone.
Then, WAIT for the camera's LED to flash blue only.
e.
Press NEXT on the app.
a. On the Pair Your Camera screen, press Generate QR Code. After
a brief wait, the code appears.
b. Show the QR code on your device to the camera from 3 – 8 inches
away. You will be notified when the code has been successfully
scanned.
c. Select your security system's Wi-Fi network and press NEXT.
d. Enter the network password and press NEXT. Final setup begins.
When the app displays Setup Successful, the process is complete*.
Press DONE or ADD ANOTHER CAMERA.
After setup, go back to the CAMERAS page and check your
newly-registered camera.
Touch the preview image to launch a live stream from the camera.
*The app will tell you if you need to repeat the setup process. This
involves resetting the camera, which is described in the
app itself.
See the other side of this sheet for more information about the
required steps.
Wi-Fi.
[Make

Advertisement

   Related Manuals for Honeywell IPCAM-WIC2

   Summary of Contents for Honeywell IPCAM-WIC2

  • Page 1: Quick Installation Guide

    Quick Installation Guide IPCAM-WIC2 is a 1080p, full HD Wi-Fi video camera intended for indoor use with Honeywell Total Connect® 2.0. Low-light operation is indicated by four red LEDs located on the front of the camera, arranged around the lens.
  • Page 2 Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar emcaráterprimário. su operación no deseada. TRADEMARKS Honeywell is a registered trademark of Honeywell International Inc. For online support visit, https://mywebtech.honeywell.com/ For the latest warranty information, visithttp://www.security.honeywell.com/hsc/resources/wa/ ‡800-23609KŠ 2 Corporate Center Drive, Suite 100 P.O.

This manual also for:

Ipcam-wic1

Comments to this Manuals

Symbols: 0
Latest comments: