Machine Switching Off; Disassembling/Assembling The Cover Panels - Saeco CAP001/A Instruction And Maintenance Manual

ON/OFF TIME
This function allows the programming of the machine's automatic
switch-on/off times for the whole of a weekly time span.
- By confirming " ON/OFF TIME", the cursor will be posi-
tioned on the day to be modified.
- Program the day with key
from upper to lower case.
- Remove the day from program, with key
from upper to lower case.
- Confirm the modification.
To modify the timetable follow the same procedure used for the
setting of the clock.
Example: The functions flow chart details a program whereby the
machine is started at 08:00 and stopped at 18:00 Monday to
Friday; from 09:00 to 12:30 on Saturday and a complete pause
on Sunday.
COUNTERS
These are two functions that represent respectively the total number
of coffee dispensing cycles and the total number of hot water
dispensing cycles.
When the automatic hot water dosing is disabled (see function
"HOT WATER PROGRAMM."), a cycle will be counted for
each command to the solenoid valve.
N.B.: Both functions are read-only and they cannot be reset.
ANTIFREEZING
The anti-freeze function protects the machine from possible dam-
age caused by exposure to low temperatures, in "STANDBY"
status, causing the formation of ice in the boilers. This function
maintains the boiler temperature at a minimum value that avoids
freezing.
- By confirming "ON", the function is enabled.
- By confirming "OFF", it is disabled.
N.B.: the function is activated only if function "AUTOMATIC
OPERATION" is also activated and at the same time the ma-
chine is in "STANDBY". When the function is activated the dis-
play shows "ANTIFREEZING".
UNBLOCKING
This function allows the temporary release of the machine, when it
has reached the number of programmed cycles for maintenance
or descaling. To obtain the releasing code, the user must contact
the firm that was responsible for installation or was appointed to
supply maintenance service. Having obtained the code, it must be
inserted in the function:
- Confirm function "UNBLOCKING", the cursor is positioned
under the first digit to be modified;
- insert the value and confirm;
- after each confirmation the cursor is positioned under the next
digit and so on, until the whole code is complete.
(down), thus shifting the letter
(up), shifting letter
6.15

Machine switching off

Automatic programmed switching off
It is possible when the function "AUTOMATIC OPERATION"
(see "6.14.2 Functions description") is active and the program-
ming of "ON/OFF TIME" (see 6.14.2 Functions description)
has also been carried out.
At the programmed time the machine is set on "STANDBY".
Manual switching off
This type of switching off is necessary when function "AUTO-
MATIC OPERATION" (see "6.14.2 Functions description") is
not activated.
It is obtained by setting both the main switch (ref. 10, fig. 1) and
the multi-pole switch to position "O" or disconnecting the plug.
6.16 Disassembling/assembling
the cover panels
"CAUTION: To Reduce the Risk of Electric shock or Mechanical
Injury, Do Not Remove This Cover. No User Serviceable Parts
Inside. Repair and Cleaning Should Be Done By Authorised Serv-
ice Personnel Only (Only for USA and CDN models)."
The side panels (ref. 1 and 5, fig. 11) and the back panel (ref. 3,
fig. 11) can be dismantled for servicing or for customization that
may suit room furniture or wall painting.
Danger
Operation falling within the competence of the Maintenance
technician.
Disconnect the machine from mains by way of main switch (ref.
10, fig. 1) and all-pole switch, or disconnecting the plug.
Danger of burns
Wait for the machine to cool off sufficiently, before servicing
it.
For parts removal, do the following:
- Pull out the drip tray (ref. 15, fig. 11).
- Manually rotate the studs (ref. A, fig. 11) by 1/4 of a turn
with a 4 mm hexagonal spanner and slide side panels (ref. 1
and 5, fig. 11) upwards.
- Slide glass out (ref. 2, fig. 11).
- Dismantle the cup heating plate (ref. 4, fig. 11) by disconnect-
ing it from the electronic board, from the earth cable and from
the drain tube (ref. B, fig. 11).
- Unscrew the back panel retaining nuts (ref. 3, fig. 11) and
dismantle it.
To re-assemble one must:
- Assemble the back panel (ref. 3, fig. 11) and secure it with the
relative nuts.
English
17