Wiring An Auxiliary Device; Optional Accessories; Warranty - CBA RA-4961Q Manual

CBA Wireless Alert System

Wiring an Auxiliary Device:

1. To connect an auxiliary notification device to channel 4, flip the left (relay) switch to "ON".
2. Flip the right (time) switch to 2 for a 2-second activation time or 5 for a 5-second activation time.
3. Wire the auxiliary device to the wiring terminal according to the diagram below.
4. When channel 4 is activated, the auxiliary device will also be triggered.
Note: Default positions are "OFF" (relay) and "2" (time).

Optional Accessories:

Wireless
Outdoor PIR Mailbox/Tilt
Sensor
RA-4961-DSQ RA-4961-MBQ
FCC COMPLIANCE STATEMENT:
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Notice:
The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change
to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the
RF exposure requirements and void user's authority to operate the device.
LIMITED WARRANTY:
used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM's obligation is limited to
the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty
is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole
obligation of SECO - LARM and the purchaser's exclusive remedy, shall be limited to the replacement or repair only, at
SECO-LARM's option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damage of any kind to the purchaser or anyone else.
NOTICE:
The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. Trademarks
are the property of SECO-LARM USA Inc. or their respective owners.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
SECO-LARM
16842 Millikan Avenue, Irvine, CA 92606
Phone: (949) 261-2999 | (800) 662-0800
8
Wireless Wireless
Magnetic
Sensor Contact
RA-4961-MCQ
This SECO-LARM product is warranted against defects in material and workmanship while
®
U.S.A., Inc.
1A@50VDC
Wireless
Indoor PIR
Sensor
RA-4961-PRQ
RA-4961-PBQ FCC ID: YAHDCX-800
Website: www.seco-larm.com
Email: sales@seco-larm.com
TERMINALS
Wireless
Pushbutton
RA-4961-PBQ
MiRA-4961-K1Q_151001.doc
SECO-LARM U.S.A., Inc.
Wireless
Vibrating
Receiver
RA-4961-VPQ
PIHVK1