Mitsubishi GOT1000 User Manual page 2

3) The following screen is displayed.
Click [ Finish ].
® ®
If using Windows 2000 or Windows XP, proceed to step 4).
® ® ®
- If Windows 98, Windows 98SE or Windows Millennium Edition is used,
installation of the USB Serial Port software begins, and ends automatically.
The CD-ROM can be removed from the personal computer at this time.
The installation of the USB driver software is finished.
4) The following screen is displayed.
Click [ Next > ].
The installation of the USB Serial Port software will begin.
®
- If using Windows 2000, a screen to select the location of the installation files
is displayed.
Please select the CD-ROM drive.
®
5) The screen of 2) is displayed. (Only in Windows XP)
Click [ Continue Anyway ].
6) The following screen is displayed.
Click [ Finish ].
The installation of the USB Serial Port software will finish.
The CD-ROM (USB driver software) can be removed from the personal
computer at this time.
7. Installation Confirmation of Driver, Setting Software
7.1 Installation Confirmation of Driver
Procedure for confirming the installation of the driver is described below.
®
Windows XP example follows.
• In Windows ® XP, click [ Start ] → [ Settings ] → [ Control Panel ] →
[ Peformance and Maintenance ] → [ System ] → [ Hardware ] →[ Device
Manager (D) ] and the window below will be displayed.
Please confirm the COM number to which the USB driver is allocated (COM and
LPT).
• If using Windows ® ® ®
98, Windows 98SE, Windows Millennium Edition or
®
Windows 2000
A screen that is equivalent to the one below is displayed by clicking [ My
Computer ] → [ Control Panel ] → [ System ] → [ Device Manager ] in the menu of
the personal computer.
B
A
Check following:
- GT10-RS2TUSB-5S is indicated at A).
- GT10-RS2TUSB-5S (COM *) is indicated at B).
* indicates the COM number used in Conversion adapter.
- Install the driver again when is displayed.
Select the programming software COM number as the COM number currently
assigned on the screen above.
7.2 Setting Software
7.2.1 Setting GT Designer2
Click [ Communication ] → [ To/From GOT... ] → [ Communication configuration tab ]
→ [ RS232 ].
Select the same COM number as the COM number of the personal computer when the
setting communication port screen appears.
Click [ OK ] .
7.2.2 Setting GX Developer
• Connectiong to Q/QnACPU
1) Click [ Online ] → [ Transfer Setup ] .
2) Double-click [ PLC module ] of PLC side I/F.
3) Check [ via GOT [ direct coupled ] transparent mode ].
4) Double-click [ Serial ] of PC side I/F.
Check [ RS-232 ].
Select the same COM number as the COM number of the personal computer
when the setting COM number screen appears.
Click [ OK ] .
• Connectiong to FXCPU
1) Click [ Online ] → [ Transfer Setup ] .
2) Double-click [ Serial ] of PC side I/F.
3) Check [ RS-232C ].
Select the same COM number as the COM number of the personal computer
when the setting COM number screen appears.
Click [ OK ].
8. Method for Uninstalling Driver
The procedure for uninstalling the driver is explained below.
®
A Windows XP example follows.
Please uninstall the driver by the procedure below.
1) Detach the USB cable from the personal computer.
On the PC display, click [ Start ] → [ Control Panel ] → [ Add or Remove
Programs ] → [GT10-RS2TUSB-5S Drivers]. The window below appears..
® ® ®
- In case of Windows Me of Windows 98 and Windows 98SE and
Windows ® Millennium Edition , Windows ® 2000
A screen that is equivalent to the one below is displayed by clicking
[ My Computer ] → [ Control Panel ] → [ Add/Remove Programs ] in the menu
of the personal computer.
Click [ Change/Remove ].
2) The following screen is displayed.
Click [ Continue ].
3) The following screen is displayed.
Click [ Finish ].
9. Troubleshooting
If communication cannot be established between the GOT and a PC using
conversion adaptor, confirm the following status by checking display LED in
conversion adaptor.
State of POWER LED Contents
The DC5V power supply from the personal computer is
POWER LED is lit. normally supplied. In case of no communication, check
the status of SD LED and RD LED.
The DC 5V power supply from the personal computer is
not supplied. Check the items below.
POWER LED is not lit. • Confirm that the specified cable is used to connect
the personal computer.
• Check that the OS is running on the PC.
The status of SD
Contents
LED and RD LED.
Blinking Communicating correctly
• Confirm the personal computer and the GOT are
connected properly with the specified cable.
• Check that the software settings on the PC
SD
Extinguished are correct.
Refer to the Section7.2 Setting software.
For details on software setting procedures, refer to the
respective software manual. .
Blinking Data receiving
• Confirm that the power is supplied to GOT.
• Confirm the personal computer and the GOT are
connected properly with the specified cable.
RD
Extinguished • Check that the software settings on the PC are
correct. Refer to the Section7.2 Setting software.
For details on software setting procedures, refer to the
respective software manual. .
* When the driver softwares for FX-USB-AW/FX3U-USB-BD and GT10-RS2TUSB-
5S are installed, uninstalling one of these driver softwares may cause the other not
to function properly. When this happens, reinstall the driver software.
* When driver installation is required after already establishing USB communication.
→ This product requires USB Driver Installation for each USB port to be
connected. Connect the product to a driver-installed USB port, or install the
driver to the current port.
This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be
the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the
Mitsubishi products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For safe use
• This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
•
This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310,
JAPAN
HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN