Mitsubishi GOT1000 Startup Manual
Gt1020/gt1030-to-fr-e 700 inverter
Hide thumbs
Also See for GOT1000:
- Connection manual (1216 pages) ,
- User manual (202 pages) ,
- Information (4 pages)
Advertisement
Quick Links
Download this manual
See also:
User Manual
GT1020/GT1030-to-FR-E 700 Inverter
Note: This document is for reference only. For detailed settings and safety information refer to the respective product manual.
START- - - - UP GUIDE
START
START
START
UP GUIDE
UP GUIDE
UP GUIDE
1
Advertisement
Related Manuals for Mitsubishi GOT1000
Summary of Contents for Mitsubishi GOT1000
- Page 1 START START START START- - - - UP GUIDE UP GUIDE UP GUIDE UP GUIDE GT1020/GT1030-to-FR-E 700 Inverter Note: This document is for reference only. For detailed settings and safety information refer to the respective product manual.
- Page 2 Hardware Introduction: The GT1020 and GT1030 are monochrome, 3-color backlight, two communication channel GOT1000 Series touch panel interfaces used for capturing user input to a system. It should be noted that not all products from the GT1020 or GT1030 range are compatible with a FREQROL inverter connection.
- Page 3 Communication For the GT1020/GT1030 to communicate with the inverter, a communication cable is required. The type of cable used is dependent on the number of inverters used within the system, examples of which are illustrated below. One inverter: Multi-drop connection: *1 Connect to the PU port of the inverter.
- Page 4 Inverter Wiring Diagrams *1 The connector figure shows the engagement face. Note: This document is for reference only. For detailed settings and safety information refer to the respective product manual.
- Page 5 GOT Terminals The GT1020/GT1030 is fitted with screw terminals, use a small flathead screwdriver to secure the wires within the PLC Communication Connector. Terminal points are illustrated below: Programming Cables: The GT1020 and GT1030 come pre-installed with an OS and FX communication driver, but without any project data.
- Page 6 GT Designer 2 (Version 2.73 or later) To make sure the GT1020/GT1030 GOT is able to use the latest functions and features, it is the responsibility of the user to check and update the firmware (Standard monitor OS) of the GOT. Launch the latest copy of GT Designer2 and start a new project for the corresponding GOT model (GT1020 or GT1030) with the “FREQROL500/700”...
- Page 7 While the “Please install the OS” screen is displayed, go to the “OS Install -> GOT” tab in the “Communicate with GOT” window of GT Designer2 and select “Standard monitor OS” and select ‘FREQROL 500/700’ from the ‘Communication Driver’ menu. Use the “Install” button to initiate the data transfer and update the firmware.
- Page 8 9999 Communication check time interval Suspension Wait time setting Pr.123 CR/LF selection Pr.124 With CR, without LF Protocol selection Pr.549 Mitsubishi inverter protocol Operation mode Pr.79 PU operation mode selection Communication startup Pr.340 Network operation mode mode selection EEPROM write Pr.342...
- Page 9 When setting the station number indirectly, the station number of the inverter can be changed using the 16-bit GOT internal data register (GD10 to GD25). When specifying the station No. from 100 to 155 on GT Designer 2, the value within GD10 to GD25 is equal to the station No.
- Page 10 Manual References: Refer to the following manuals for more detailed explanations. For any further questions, please contact your local Mitsubishi Product Provider. GOT1000 Series Connection Manual 3/3 (SH(NA)-080532ENG) Sections 32.1, 32.2, 32.3, 32.4, 32.5 & 32.6 FR-E700 Instruction Manual Inverter (IB(NA)-0600336ENG-B)